DLA MIL-DTL-24211 2 E-2013 GASKETS WAVEGUIDE FLANGE (FLAT FACE).pdf

《DLA MIL-DTL-24211 2 E-2013 GASKETS WAVEGUIDE FLANGE (FLAT FACE).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-24211 2 E-2013 GASKETS WAVEGUIDE FLANGE (FLAT FACE).pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5985 INCH-POUND MIL-DTL-24211/2E 6 November 2013 SUPERSEDING MIL-DTL-24211/2D 20 March 2009 DETAIL SPECIFICATION SHEET GASKETS, WAVEGUIDE FLANGE (FLAT FACE) This specification is approved for use by all Departments and Agencies of the Department of Defense. The complete requirements fo

2、r procuring the gaskets described herein shall consist of this specification sheet and MIL-DTL-24211. REQUIREMENTS: Dimensions and configuration: See figure 1. Reference data: See table I. Part number: M24211/2-(number taken from figure 1). TABLE I. Reference data. Part number M24211/2- Used with fl

3、anges M3922/ Part number M24211/2- Used with flanges M3922/ 001 52-001, 52-002 010 52-019, 52-020 002 52-003, 52-004 011 52-021, 52-022 003 52-005, 52-006 012 XX-001 004 52-007, 52-008 013 XX-002 005 52-009, 52-010 014 XX-003 006 52-011, 52-012 015 XX-004 007 52-013, 52-014 016 XX-005 008 52-015, 52

4、-016 017 XX-006 009 52-017, 52-018 018 XX-007 019 75-15, 75-16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 2 Configuration 1. Gasket configuration for part numbers 001-011. FIGURE 1. Gasket. Provided by IHSNot for ResaleNo reprod

5、uction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 3 Configuration 2. Gasket configuration for part number 012. FIGURE 1. Gasket - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 4 Configuration 3

6、. Gasket configuration for part number 013. FIGURE 1. Gasket - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 5 Configuration 4. Gasket configuration for part number 014. FIGURE 1. Gasket - Continued. Provided by IHSNot f

7、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 6 Configuration 5. Gasket configuration for part number 015. FIGURE 1. Gasket - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E

8、 7 Configuration 6. Gasket configuration for part number 016. FIGURE 1. Gasket - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 8 Configuration 7. Gasket configuration for part number 017. FIGURE 1. Gasket - Continued. Pr

9、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 9 Configuration 8. Gasket configuration for part number 018. FIGURE 1. Gasket - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

10、,-MIL-DTL-24211/2E 10 Configuration 9. Gasket configuration for part number 019. FIGURE 1. Gasket - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 11 FIGURE 1. Gasket - Continued. Provided by IHSNot for ResaleNo reproduct

11、ion or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 12 Part number M24211/2- A B C D BSC. E BSC. F G BSC. 001 6.500 .005 (165.10 .13) 3.250 .005 (82.55 .13) 8.690 .020 (220.73 .51) 1.249 (31.72) 2.311 (58.70) .330 .005 (8.38 .13) 2.374 (60.30) 002 5.100 .005 (129.54 .13) 2.550

12、.005 (64.77 .13) 7.160 .020 (181.86 .51) 1.031 (26.19) 1.925 (48.90) .266 .005 (6.76 .13) 1.987 (50.47) 003 4.300 .005 (109.22 .13) 2.150 .005 (54.61 .13) 6.340 .020 (161.04 .51) .938 (23.83) 1.720 (43.69) .266 .005 (6.76 .13) 1.787 (45.39) 004 3.400 .005 ( 86.36 .13) 1.700 .005 (43.18 . 13) 5.440 .

13、020 (138.18 .51) .671 (17.04) 1.500 (38.10) .266 .005 (6.76 .13) 1.344 (34.14) 005 2.840 .005 (72.14 .13) 1.340 .005 (34.04 .13) 4.500 .020 (114.30 .51) .578 (14.68) 1.164 (29.57) .257 + .005 (6.53 + .13) - .000 1.281 (32.54) 006 2.290 .005 (58.17 .13) 1.145 .005 (29.08 .13) 3.880 .020 (98.55 .51) .

14、500 (12.70) 1.050 (26.67) .257 + .005 (6.53 + .13) - .000 1.070 (27.18) 007 1.872 .005 (47.55 .13) .872 .005 (22.15 .13) 3.500 .020 (88.90 .51) .438 (11.13) .914 (23.22) .257 + .005 (6.53 + .13) - .000 .562 (14.27) 008 1.590 .004 (40.39 .10) .795 .004 (20.19 .10) 3.190 .020 (81.03 .51) .375 (9.53) .

15、875 (22.23) .257 + .005 (6.53 + .13) - .000 .500 (12.70) 009 1.372 .004 (34.85 .10) .622 .004 (15.80 .10) 2.690 .020 (68.33 .51) .313 (7.95) .719 (18.26) .196 + .004 (4.98 + .10) - .000 .438 (11.13) 010 1.122 .004 (28.50 .10) .497 .004 (12.62 .10) 2.500 .020 (63.50 .51) .312 (7.92) .640 (16.26) .169

16、 + .002 (4.29 + .05) - .000 .375 (9.53) 011 .900 .003 (22.86 .08) .400 .003 (10.16 .08) 2.090 .020 (53.09 .51) .312 (7.92) .578 (14.68) .169 + .002 (4.29 + .05) - .000 .312 (7.92) 012 7.700 .006 (195.58 .15) 3.850 .006 (97.79 .15) 11.219 .015 (284.96 .38) 1.000 (25.40) 2.925 (74.30) .406 + .010 (10.

17、31 + .25) - .000 2.000 (50.80) 013 9.750 .006 (247.65 .15) 4.875 .006 (123.82 .15) 13.250 .015 (336.55 .38) 1.000 (25.40) 3.437 (87.30) .406 + .010 (10.31 + .25) - .000 2.000 (50.80) 014 11.500 .007 (292.10 .18) 5.750 .007 (146.05 .18) 15.000 .030 (381.00 .76) 0.969 (24.6) 3.875 (98.42) .406 + .010

18、(10.31 + .25) - .000 3.000 (76.20) 015 15.000 .007 (381.00 .18) 7.500 .007 (190.50 .18) 18.500 .030 (469.90 .76) 1.000 (25.40) 4.750 (120.6) .406 + .010 (10.31 + .25) - .000 3.000 (76.20) 016 18.000 .008 (457.20 .20) 9.000 .008 (228.60 .20) 21.500 .030 (546.10 .76) 0.907 (23.0) 5.500 (139.7) .406 +

19、.010 (10.31 + .25) - .000 2.000 (50.80) 017 21.000 .010 (533.40 .25) 10.500 .010 (266.70 .25) 24.625 .030 (625.48 .76) 1.300 (33.02) 6.500 (165.1) .531 + .010 (13.49 + .25) - .000 3.917 (99.49) 018 23.000 .010 (584.20 .25) 11.500 .010 (292.10 .25) 26.625 .030 (676.28 .76) 0.930 (23.6) 7.000 (177.8)

20、.531 + .010 (13.49 + .25) - .000 3.345 (84.96) 019 9.750 .005 (247.65 .13) 2.436 .005 (61.87 .13) 13.250 .015 (336.55 .38) - 1.500 (38.10) .406 + .010 (10.31 + .25) - .000 2.000 (50.80) FIGURE 1. Gasket - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

21、 from IHS-,-,-MIL-DTL-24211/2E 13 Part number M24211/2- H J K L .010 (.25) M .010 (.25) N P R .010 (.25) 001 3.937 (100.00) .012 (.30) 5.440 .020 (138.18 .51) 7.188 (182.58) .188 (4.78) .012 (.30) .005 (.13) 3.938 (100.03) 002 3.200 (81.28) .011 (.28) 4.620 .020 (117.35 .51) 5.844 (148.44) .188 (4.7

22、8) .011 (.28) .005 (.13) 3.281 (83.34) 003 2.795 (70.99) .011 (.28) 4.190 .020 (106.43 .51) 4.884 (124.05) .172 (4.37) .011 (.28) .005 (.13) 2.728 (69.29) 004 2.344 (59.54) .011 (.28) 3.750 .020 (95.25 .51) 3.984 (101.19) .172 (4.37) .011 (.28) .005 (.13) 2.284 (58.01) 005 1.914 (48.62) .007 (.18) 3

23、.000 .020 (76.20 .51) 3.338 (84.79) .156 (3.96) .004 (.10) .005 (.13) 1.838 (46.69) 006 1.620 (41.15) .007 (.18) 2.750 .020 (69.85 .51) 2.750 (69.85) .156 (3.96) .005 (.13) .005 (.13) 1.605 (40.77) 007 1.414 (35.92) .007 (.18) 2.500 .020 (63.50 .51) 2.330 (59.18) .156 (3.96) - .005 (.13) 1.330 (33.7

24、8) 008 1.273 (32.33) .007 (.18) 2.440 .020 (61.98 .51) 2.050 (52.07) .156 (3.96) - .004 (.10) 1.255 (31.88) 009 1.094 (27.79) .006 (.15) 1.940 .020 (49.28 .51) 1.782 (45.26) .110 (2.79) - .004 (.10) 1.032 (26.21) 010 .953 (24.21) .005 (.13) 1.750 .020 (44.45 .51) 1.532 (38.91) .110 (2.79) - .004 (.1

25、0) .907 (23.04) 011 .828 (21.03) .005 (.13) 1.590 .020 (40.39 .51) 1.300 (33.02) .110 (2.79) - .003 (.08) .800 (20.32) 012 4.850 (123.2) .030 (.76) 7.375 .015 (187.32 .38) 8.530 (216.66) .188 (4.78) - .006 (.15) 4.680 (118.87) 013 5.875 (149.2) .030 (.76) 8.375 .015 (212.72 .38) 10.532 (267.51) .203

26、 (5.16) - .006 (.15) 5.657 (143.69) 014 6.750 (171.4) .030 (.76) 9.250 .015 (234.95 .38) 12.600 (320.04) .234 (5.94) - .007 (.18) 6.850 (173.99) 015 8.500 (215.9) .030 (.76) 11.000 .015 (279.40 .38) 16.064 (408.03) .234 (5.94) - .007 (.18) 8.564 (217.53) 016 10.000 (250.0) .030 (.76) 12.500 .030 (31

27、7.50 .76) 19.064 (484.23) .234 (5.94) - .008 (.20) 10.064 (255.63) 017 11.750 (298.45) .030 (.76) 14.125 .030 (358.78 .76) 21.970 (558.04) .212 (5.38) - .010 (.25) 11.470 (291.34) 018 12.750 (323.85) .030 (.76) 15.125 .030 (384.18 .76) 23.850 (605.79) .234 (5.94) - .010 (.25) 12.350 (313.69) 019 5.8

28、75 (149.2) .030 (.76) 4.500 .015 (114.30 .38) 10.450 (265.43) .140 (3.56) - .005 (.13) 3.237 null .005 (82.22 null 0.13) FIGURE 1. Gasket - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 14 Part number M24211/2- S .010 (.

29、25) T U V .005 (.13) W X .02 (.51) Y 001 .375 (9.52) .330 .005 (8.38 .13) .25 (6.35) .020 (.51) .050 (1.27) .19 (4.83) .005 (.13) 002 .250 (6.35) .266 .005 (6.76 .13) .25 (6.35) .020 (.51) .050 (1.27) .16 (4.06) .005 (.13) 003 .250 (6.35) .266 .005 (6.76 .13) .25 (6.35) .020 (.51) .050 (1.27) .16 (4

30、.06) .005 (.13) 004 .367 (9.32) .266 .005 (6.76 .13) .25 (6.35) .020 (.51) .050 (1.27) .16 (4.06) .005 (.13) 005 .280 (7.11) .257 .003 (6.53 .08) .31 (7.87) .020 (.51) .050 (1.27) .09 (4.83) .005 (.13) 006 .140 (3.56) .257 .002 (6.53 .05) .31 (7.87) .020 (.51) .050 (1.27) .09 (4.83) .005 (.13) 007 .

31、260 (6.60) - .31 (7.87) .020 (.51) .030 (.76) .09 (4.83) .005 (.13) 008 .140 (3.56) - .31 (7.87) .020 (.51) .030 (.76) .09 (4.83) .004 (.10) 009 .236 (5.99) - .25 (6.35) .026 (.66) .030 (.76) .09 (4.83) .004 (.10) 010 .236 (5.99) - .25 (6.35) .026 (.66) .030 (.76) .09 (4.83) .004 (.10) 011 .231 (5.8

32、7) - .25 (6.35) .026 (.66) .030 (.76) .09 (4.83) .003 (.08) 012 .540 (13.72) - .25 (6.35) .020 (.51) .050 (1.27) .22 (5.59) .005 (.13) 013 .516 (13.11) - .25 (6.35) .020 (.51) .050 (1.27) .22 (5.59) .005 (.13) 014 .500 (12.70) - .25 (6.35) .020 (.51) .050 (1.27) .22 (5.59) .005 (.13) 015 .657 (16.69

33、) - .25 (6.35) .020 (.51) .050 (1.27) .22 (5.59) .005 (.13) 016 .657 (16.69) - .25 (6.35) .020 (.51) .050 (1.27) .22 (5.59) .005 (.13) 017 .563 (14.30) - .25 (6.35) .020 (.51) .050 (1.27) .22 (5.59) .005 (.13) 018 .551 (14.00) - .25 (6.35) .020 (.51) .050 (1.27) .22 (5.59) .005 (.13) 019 .200 (5.08)

34、 - .25 (6.35) .026 (.66) .031 (.79) .16 (4.06) .005 (.13) FIGURE 1. Gasket - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/2E 15 Part number M24211/2- AA AB AC AD AE AF AG AH 012 - - - 4.000 (101.6) - - - - 013 - - - 4.000

35、(101.6) 3.000 (76.20) - - - 014 - - - 5.000 (127.0) 2.907 (73.84) - - 1.000 (25.40) 015 - - - 5.000 (127.0) 3.000 (76.20) 7.000 (177.8) - 1.000 (25.40) 016 4.532 (115.1) - 8.000 (203.2) 4.000 (101.6) 2.719 (69.06) 6.000 (152.4) - - 017 6.061 (153.9) - 11.311 (287.30) 6.528 (165.8) 3.900 (99.06) 9.13

36、9 (232.1) - 1.306 (33.17) 018 4.651 (118.1) 6.511 (165.4) 10.032 (254.8) 5.574 (141.6) 2.790 (70.87) 7.803 (198.2) 12.261 (311.4) 1.116 (28.35) 019 - - - 4.000 (101.6) - - - - INCHES MM INCHES MM INCHES MM INCHES MM INCHES MM 0.010 .25 1.306 33.17 3.900 99.06 5.875 149.22 8.000 203.20 0.015 .38 2.00

37、0 50.80 3.917 99.49 6.000 152.40 8.500 215.90 0.020 .51 2.719 69.06 4.000 101.60 6.061 153.95 9.139 232.13 0.030 .76 2.790 70.87 4.532 115.11 6.500 165.10 10.000 254.00 0.907 23.04 2.907 73.84 4.651 118.14 6.511 165.38 10.032 254.81 0.930 23.62 2.925 74.30 4.750 120.65 6.528 165.81 11.311 287.30 0.9

38、69 24.61 3.000 76.20 4.850 123.19 6.750 171.45 11.750 298.45 1.000 25.40 3.345 84.96 5.000 127.00 7.000 177.80 12.261 311.43 1.116 28.35 3.437 87.30 5.500 139.70 7.803 198.20 12.750 323.85 1.300 33.02 3.875 98.43 5.574 141.58 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parenthes

39、es. 3. Metric equivalents are given for general information only and are based upon 1.00 inch = 25.4 mm. 4. Electrical contact area to be .004 (.10 mm) .001 (.03 mm) higher than adjacent metal surface. 5. Roughness of mating surfaces other than the raised electrical contact area shall not exceed 63

40、microinches in accordance with ASME-B46.1 except that flaws shall be included in the roughness height measurement. 6. Any raised embossed pattern for electrical contact is acceptable provided R.F. leakage requirement is met. Provided by IHSNot for ResaleNo reproduction or networking permitted withou

41、t license from IHS-,-,-MIL-DTL-24211/2E 16 Referenced documents. In addition to MIL-DTL-24211, this document references the following: ASME-B46.1 Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Prep

42、aring activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5985-2013-048) Review activities: Army - AR Navy - AS, CG, MC, OS, SH Air Force - 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-