DLA MIL-D-3954 C (3)-2002 DUMMY LOADS ELECTRICAL WAVEGUIDE GENERAL SPECIFICATION FOR《电子波导仿真载荷的一般规范》.pdf

《DLA MIL-D-3954 C (3)-2002 DUMMY LOADS ELECTRICAL WAVEGUIDE GENERAL SPECIFICATION FOR《电子波导仿真载荷的一般规范》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-D-3954 C (3)-2002 DUMMY LOADS ELECTRICAL WAVEGUIDE GENERAL SPECIFICATION FOR《电子波导仿真载荷的一般规范》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-D-3954C AMENDMENT 3 28 March 2002 SUPERSEDING AMENDMENT 2 29 March 1979 MILITARY SPECIFICATION DUMMY LOADS, ELECTRICAL, WAVEGUIDE, GENERAL SPECIFICATION FOR This amendment forms a part of MIL-D-3954C, dated 19 November 1973, and is approved for use by all Departments and Agencies of the Departm

2、ent of Defense. PAGE 1 Federal specifications: Delete ”QQ-A-250/1 - Aluminum Alloy 11, Plate and Sheet” and substitute ”SAE AMS-QQ-A-250/1 - Aluminum 1100, Plate and Sheet.” PAGE 2 Military specifications: Delete ”MIL-B-20148 - Brazing Sheet, Aluminum Alloy” and substitute ”SAE AMS-B-20148 - Brazing

3、 Sheet, Aluminum Alloy.” PAGE 3 3.2: Delete and substitute: “3.2 First article. Dummy loads furnished under this specification shall be products which have been tested and have passed the first article inspection specified in 4.5 (see 6.3).” 3.3, first sentence: Delete and substitute: “The material

4、for each part shall be as specified herein.” 3.3(a): Delete and substitute: “Aluminum alloy plates and sheets shall conform to SAE AMS-QQ-A-250/11 or SAE AMS-QQ-A-250/1; extruded aluminum alloy shall conform to SAE AMS-QQ-A-200/9 or SAE AMS-QQ-A-250/11.” 3.3(f): Delete and substitute: “Aluminum allo

5、y brazing sheets shall conform to Alcoa #11, or equivalent, in accordance with class 1 of SAE AMS-B-20148. AMSC N/A 1 of 6 FSC 5985 Distribution Statement A. Approved for public release; distribution is unlimited. INCH-POUND * * * * * Provided by IHSNot for ResaleNo reproduction or networking permit

6、ted without license from IHS-,-,-MIL-D-3954C AMENDMENT 3 2 PAGE 5 4: Delete and substitute: “4. VERIFICATION” 4.1: Delete and substitute: “4.1 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.5). b. Conformance

7、inspection (see 4.6). 4.1.1: Delete. 4.2: Delete and substitute: “4.2 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The abse

8、nce of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acce

9、ptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material.” Add the following new paragraphs: “4.4.1 Test method variation. Variation fr

10、om the specified test method used to verify the electrical parameters are allowed provided that it is demonstrated to the preparing activity or to their agent that such variations in no way relax the requirements of this specification and that they are approved before testing is performed. For propo

11、sed test variations, a test method comparative error analysis shall be made available for checking by the preparing activity or their agent. 4.4.2 Test equipment and inspection facilities. Test and measuring equipment and inspection facilities of sufficient accuracy, quality, and quantity to permit

12、performance of the required inspection shall be established and maintained by the supplier. The establishment and maintenance of a calibration system to control the accuracy of the measuring and test equipment shall be in accordance with ANSI-Z540.1. 4.4.3 Accuracy of test equipment. The frequency-m

13、easuring device used shall have an accuracy of 0.1 percent or better. The overall accuracy in the determination of VSWR shall be better than 2 percent.” * * * * * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-3954C AMENDMENT 3 3 PAGE 5 4.5: D

14、elete and substitute: “4.5 First article inspection. Unless otherwise specified (see 6.2), 3 dummy loads of each class shall be required for first article inspection. First article inspection shall consist of the tests specified in table II and performed by the supplier, after award of contract and

15、prior to production, at a location acceptable to the Government. First article inspection shall be performed on sample units, which have been produced with equipment and procedures normally, used in production. First article approval is valid only on the contract or purchase order under which it is

16、granted, unless extended by the Government to other contracts or purchase orders.” PAGE 6 4.5.1 and 4.5.2: Delete. 4.5.3, 4.5.4: Delete and substitute: “4.5.3 Failures. One or more failures shall be cause for refusal to grant first article approval. 4.5.4 Disposition of sample units. Sample units, w

17、hich have been subjected to first article testing, shall not be delivered on the contract. 4.6.1 through 4.6.1.1.1.1: Delete and substitute: “4.6.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A inspection. 4.6.1.1 Inspection lot. An inspection lot sh

18、all consist of all dummy loads of the same PIN produced under essentially the same conditions, and offered for inspection at one time. 4.6.1.1.1 Group A inspection. Group A inspection shall consist of the inspection specified in table III in the order shown. 4.6.1.1.1.1 Sampling plan (group A). Tabl

19、e III tests shall be performed on a production lot basis. Samples shall be selected in accordance with table IIIa. If one or more defects are found, the lot shall be screened for that particular defect and defects removed. A new sample of parts shall be selected in accordance with table IIIa and all

20、 group A tests again performed. If one or more defects are found in the second sample, the lot shall be rejected and shall not be supplied to this specification.” * * * * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-3954C AMENDMENT 3 4 PAGE

21、6 Table II, title: Delete and substitute. “TABLE II. Examinations and tests.” Add the following table and notes: TABLE IIIa. Inspection level. Visual and mechanical inspection Lot size Major Minor 1/1 to 8 9 to 15 16 to 25 26 to 50 51 to 90 91 to 150 151 to 280 281 to 500 501 to 1,200 1,201 to 3,200

22、 3,201 to 10,000 10,000 to 35,000 35,001 to 150,000 150,0001 to 500,000 500,001 and over All All 20 20 20 20 20 47 47 53 68 77 96 119 143 5 5 5 5 7 11 13 16 19 23 29 35 40 40 40 1/ Samples may be pulled from either the production lot itself or from samples pulled from the lot for major defect testin

23、g. In no case will the sample size exceed the lot size. NOTES: 1. Major defect: A major defect is a defect, other than critical, that is likely to result in failure, nor to reduce materially the usability of the unit of product for its intended purpose. 2. Minor defect: A minor defect is a defect th

24、at is not likely to reduce materially the usability of the unit of product for its intended purpose, or is a departure from established standards having little bearing on the effective use or operation of the unit. PAGE 7 4.6.2 through 4.6.2.1.3: Delete and substitute: “4.6 2 Conformance inspection.

25、 Conformance inspection shall consist of group B. Except where the results of these inspections show noncompliance with the applicable requirements (see 4.6.2.1.4), delivery of products, which have passed group A shall not be, delayed pending the results of these conformance inspections. 4.6.2.1 Gro

26、up B inspection. Group B inspection shall consist of the inspections specified in table IV in the order shown, and shall be made on sample units which have been subjected to and passed the group A inspection. Dummy loads having identical piece parts may be combined for lot purposes and shall be in p

27、roportion to the quantity of each PIN numbered adapter produced. * * * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-3954C AMENDMENT 3 5 PAGE 7 4.6.2.1.1 Group B sampling plan. The group B sampling plan shall consist of 2 samples, which have

28、been previously subjected to group A testing. 4.6.2.1.2 Nonconforming production control sample units. If a sample unit fails the inspection specified in group B, the contractor shall immediately investigate the cause of failure and shall report to the procuring activity the results thereof and deta

29、ils of the corrective action taken to correct units of product, which were manufactured under the same conditions, with the same materials, processes, and so forth. No sample shall be delivered as a production item under the contract.” 4.6.2.1.3 Disposition of sample units. Sample units, which have

30、passed all the group B inspection, may be delivered on the contract or purchase order, if the lot is accepted. Any dummy load deformed or otherwise damaged during testing shall not be delivered on the contract or order. PAGE 10 4.7.9: Delete and substitute: “4.7.9 Power dissipation (see 3.12). Unles

31、s otherwise specified, the contractor shall certify that the dummy load is capable of dissipating the power as indicated in 4.7.9.1. The certificates shall be in the contractors certified test report to the procuring activity when first article testing is invoked in a contract. When specified (see 3

32、.1 and 6.2(e), the test shall be in accordance with 4.7.9.1.” Add the following new paragraph: “4.7.9.1 Power dissipation test (see 3.12). The specified peak and average power shall be applied simultaneously at any one frequency within the specified range (see 3.1). When no peak power is specified,

33、apply 1.5 times rated average power. Power shall be maintained for a period of 15 minutes after the load has reached thermal equilibrium. It is considered that thermal equilibrium has been reached when the temperature of the load has not changed by more that 5C over a period of 5 minutes. Unless oth

34、erwise specified, (see 3.1), the internal pressure of the load shall be 20 pounds per square inch gage (psig). For liquid cooled loads, the minimum flow rates and coolant pressure specified (see 3.1) shall be used with the input temperature as specified.” 4.7.10: Delete and substitute: “4.7.10 Endur

35、ance (see 3.13). Unless otherwise specified, the contractor shall certify that the dummy load is capable of passing the endurance test as indicated in 4.7.10.1. The certification shall be in the contractors certified test report to the procuring activity when first article testing is invoked in a co

36、ntract. When specified (see 3.1 and 6.2(f), the test shall be in accordance with 4.7.10.1.” * * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-3954C AMENDMENT 3 6 PAGE 10 Add the following new paragraph: 4.7.10.1 Endurance test (see 3.13). Dum

37、my loads shall be subjected to the specified peak power (when applicable) and average power for test purposes, for 10 cycles of 1 hour power on and a minimum of 1 hour off, at any frequency within the specified frequency range (see 3.1). The VSWR shall be measured as specified in 4.7.2 (and 4.7.2.1

38、if applicable) preceding the test, and at interval of 1 hour thereafter during the off period. Unless otherwise specified, (see 3.1), the internal pressure of the load shall be 30 psig. For liquid cooled loads, the minimum flow rate and coolant pressure specified (see 3.1) shall be used with the inp

39、ut temperature as specified. PAGE 12 6.2: Add: “(e) If power dissipation test is required see 4.7.9 and 4.7.9.1. (f) If endurance test is required see 4.7.10 and 4.7.10.1.” 6.3: Delete and substitute: “6.3 First article. Invitations for bid should provide that the Government reserves the right to wa

40、ive the requirement for first article samples as to those biddders offering a product which has been previously acquired or tested by the Government and that bidders offering a product which has been previously acquired or tested by the Government and that bidders offering such products who wish to

41、rely on such production or test must furnish evidence with the bid that prior Government approval is presently appropriate for the pending acquisition.” PAGE 15 Appendix: Delete in its entirety. NOTE: The margin of this amendment is marked with an asterisk to indicate where changes from the previous

42、 amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the material notations

43、 and relationship to the last previous amendment. CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 11 (Project 5985-1251) DLA - CC Review activities: Army - AR, MI Navy - AS, CG, MC, OS, SH Air Force - 19 * * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-