DLA DSCC-DWG-99011 REV B-2010 RESISTORS FIXED FILM (INSULATED) WATT.pdf

《DLA DSCC-DWG-99011 REV B-2010 RESISTORS FIXED FILM (INSULATED) WATT.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-99011 REV B-2010 RESISTORS FIXED FILM (INSULATED) WATT.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LT DESCRIPTION DATE APPROVED A 5 year review cycle. Editorial and procedural changes throughout. 2 Feb 2005 K. Cottongim B Add pure tin, manufacturer eligibility, and high power pulse paragraphs. Editorial changes throughout. 3 Dec 2010 M. Radecki Prepared in accordance with ASME Y14.100

2、Source control drawing REV STATUS REV B B B B B B OF PAGES PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Dennis L. Cross DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 19 July 1999 CHECKED BY Andrew R. Ernst TITLE RESISTORS, FIXED, FILM (INSULATED), WATT APPROVED BY Kendall A. Cotton

3、gim SIZE A CODE IDENT. NO. 037Z3 DWG NO. 99011 REV B PAGE 1 OF 6 AMSC N/A 5905-E721 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE

4、SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 99011 REV B PAGE 2 1. SCOPE * 1.1 Scope. This drawing describes the requirements for insulated, fixed, film, 1/4 watt resistors available in 2 percent, 5 percent, and 10 percent resistance tolerances. These resistors are capa

5、ble of full-load operation at an ambient temperature of 70C. Designers are CAUTIONED on using these resistors in high power pulse applications (see 6.4). 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 99011 - G 226 | | | | | | Drawing number Tolerance (see 3.3.1) Resista

6、nce value (see 3.3.2) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are th

7、ose cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-39017 - Resistors, Fixed, Film (Insulated), Nonestablished Reliability, Established Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-790 - Standard Practice for Established Reliabil

8、ity and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications. MIL-STD-1285 - Marking of Electrical and Electronic Parts. * (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standar

9、dization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) * 2.2 Order of precedence. Unless otherwise noted herein or in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of

10、 this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-39017, and as specified herein. 3.

11、2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-39017 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE ID

12、ENT NO. 037Z3 DWG NO. 99011 REV B PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Maximum length is “clean lead” to “clean lead”. 4. The end of the body shall be that point at which the body diameter equals the nearest drill size larger tha

13、n 250 percent of the nominal lead diameter. 5. Lead length for tape and reel packaging shall be 1 inch (25.4 mm) minimum (see 6.2). 6. The pictorial view of the style above does not depict the actual size and is given as representative of the envelope of the item. Slight deviations from the outline

14、shown, which are contained within the envelope, and do not alter the functional aspects of the device are acceptable. FIGURE 1. Fixed, film, resistor. 3.3 Electrical characteristics. 3.3.1 Resistance tolerance. The resistance tolerance available shall be (G) 2 percent, (J) 5 percent, and (K) 10 perc

15、ent. 3.3.2 Resistance. The nominal resistance expressed in ohms is identified by three digits; the first two digits represent significant figures and the last digit specifies the number of zeros to follow. Minimum and maximum resistance values shall be as specified in 3.3.3. Resistance values not li

16、sted in the “10 to 100“ decade of table I for the appropriate resistance tolerance shall be considered nonconforming to the specification. TABLE I. Standard resistance values for 10 to 100 decade. (G) (J) (K) (G) (J) (K) (G) (J) (K) 10.0 11.0 12.0 13.0 15.0 16.0 18.0 20.0 10.0 - 12.0 - 15.0 - 18.0 -

17、 22.0 24.0 27.0 30.0 33.0 36.0 39.0 43.0 22.0 - 27.0 - 33.0 - 39.0 - 47.0 51.0 56.0 62.0 68.0 75.0 82.0 91.0 47.0 - 56.0 - 68.0 - 82.0 - 3.3.3 Resistance range. Minimum and maximum resistance values for temperature characteristic of 350 parts per million (ppm) shall be 11 megohm and 22 megohms, resp

18、ectively. Inches mm Inches mm .002 0.05 .090 2.29 .008 0.20 .125 3.18 .016 0.41 .250 6.35 .025 0.64 .300 7.62 .031 0.79 1.500 38.10 .046 1.17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE I

19、DENT NO. 037Z3 DWG NO. 99011 REV B PAGE 4 3.3.4 Power rating. The power rating shall be 1/4 watt at +70C. For operation at temperatures higher than +70C, derate in accordance with figure 2. FIGURE 2. Derating curve 3.3.5 Voltage rating. The maximum continuous working voltage shall not exceed 250 vol

20、ts. 3.3.6 Termination. Termination material shall be in accordance with MIL-PRF-39017. * 3.3.6.1 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall

21、 be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.3.7 Solderability. The requirement for solderability shall be as specified in MIL-PRF-39017. 3.4 Marking. Full marking shall be in accordance with MIL-STD-1285, except the resistors shall be marked with the PIN as specified herein (s

22、ee 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes is required on the unit package. Due to size limitations, this style resistor shall be marked with the following minimum information in the order shown: 9XXX - Last four digits of this DSCC drawing nu

23、mber. 826D - Year and week manufactured and the manufacturers code (see qualified products list MIL-PRF-39017 for manufacturers code symbol). G220 - Resistance tolerance and resistance value. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally pr

24、eferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. * 3.6 Manufacturer eligibility. To be eligible for listing as an approved source of supp

25、ly, a manufacturer shall be listed on the MIL-PRF-39017 Qualified Products List for at least one part, or perform the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DLA Land and Maritime-VA. * 3.6.1 Certificate of compliance. A certificate of complia

26、nce shall be required from manufacturers requesting to be an approved source of supply. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 99011 REV B PAGE 5 3.7 Workmans

27、hip. Resistors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-39017 and maintained in accordance with MIL-STD-790 is not applicable to this d

28、ocument. 4.2 Qualification inspection. Qualification inspection is not applicable to this document. 4.3 Product level qualification. The product level qualification specified in MIL-PRF-39017 is not applicable to this document. 4.4 Conformance inspections. 4.4.1 Inspection of product for delivery. I

29、nspection of product for delivery shall consist of group A and group B inspections of MIL-PRF-39017. 4.4.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2e). 4.5 Visual and mechani

30、cal examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-39017. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall b

31、e as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Con

32、trol Points packaging activity within the Military Department or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsib

33、le packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Resistors conforming to this drawing are intended for use when military specifications do not exist. This drawing is intended exclusive

34、ly to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. Provided by I

35、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 99011 REV B PAGE 6 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Req

36、uirements for delivery: One copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Terminal finish. d. Requirements for packaging and packing. e. Whether the manufacturer performs the grou

37、p B tests or provides certification of compliance with group B requirements (see 4.4.2). * 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after

38、manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For

39、 additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). * 6.4 Pulse applications. Designers are CAUTIONED on using the above resistors in high power pulse applications. Since they have not been qualified nor tested for such applicatio

40、ns, damage and premature failure are possible. These resistors only see a one time pulse (Short-time overload) as part of the group B inspection of MIL-PRF-39017. * 6.5 User of record. Coordination of this document for future revisions is coordinated only with the approved source of supply and the u

41、sers of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. * 6.6 Approved source of suppl

42、y. Approved source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552

43、 or DSN 850-0552. DLA Land and Maritime drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 99011-* ERL-07-100 91637 Vishay Dale, Inc. PO Box 609 Columbus, NE 68602-0609 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-