DLA DSCC-DWG-83006 REV E-2010 FILTERS RADIO FREQUENCY INTERFERENCE.pdf

《DLA DSCC-DWG-83006 REV E-2010 FILTERS RADIO FREQUENCY INTERFERENCE.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-83006 REV E-2010 FILTERS RADIO FREQUENCY INTERFERENCE.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A The “C” dimension for dash numbers 02 and 03 was changed from 2.625 to 2.062 inches. 17 Oct 83 Randy Larson B Added listing on QPL for MIL-F-15733/75 as an alternative for manufacturer eligibility. Added another source to suggested sources of supply. Editor

2、ial changes throughout. 3 Mar 86 Patrick Kyne C Editorial changes throughout. Removed a source of supply. 19 Sep 00 K.A. Cottongim D Page 2 - Added pure tin prohibition and reference to MIL-PRF-15733. Page 6 - Added note (paragraph 6.4) regarding pure tin prohibition. Editorial changes throughout. 1

3、3 Feb. 06 M. Radecki E Editorial changes throughout. 2 Dec 2010 M. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV E E E E E E E PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Randy Larson DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH Origina

4、l date of drawing CHECKED BY Randy Larson TITLE FILTERS, RADIO FREQUENCY INTERFERENCE 27 June 1983 APPROVED BY Ivan R. Jones SIZE A CODE IDENT. NO. 14933 DWG NO. 83006 REV E PAGE 1 OF 7 AMSC N/A 5915-2011-E01 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBU

5、S, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 83006 REV E PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-15733 describe the requirements for

6、 400 Hertz power line filters designed to attenuate frequencies from 14 kHz to 10 GHz. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 83006 - XX Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in

7、sections 3 and 4 of this drawing. This section does not include documents cited in other sections of this drawing or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all s

8、pecified requirements of documents in sections 3 and 4 of this drawing, whether or not they are listed here. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. U

9、nless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-15733 - Filters and Capacitors, Radio Frequency Interference, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test

10、Methods for Electronic and Electrical Component Parts. MIL-STD-220 - Method of Insertion Loss Measurement. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 191

11、11-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing shall take precedence. Nothing in this document, however, supersedes applicable laws and regulati

12、ons unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-15733 and herein. 3.1.1 Terminals. See figure 1. 3.1.2 Case dimensions. Case dimensions shall be in accordance with figure

13、1. 3.2 Pure tin prohibition. Pure tin shall be prohibited as specified in MIL-PRF-15733 (see 6.4). 3.3 Operating temperature range. The operating temperature range shall be -55C to +85C. 3.4 Temperature rise. Temperature rise shall be in accordance with MIL-PRF-15733; 25C for parts rated up to and i

14、ncluding 10 amperes, 35C for parts rated above 10 amperes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 83006 REV E PAGE 3 Dash No. A .06 (1.52) B .06 (1.52) C .03

15、1 (.79) D .015 (.38) E .015 (.38) F .031 (.79) G .031 (.79) H Thread J Thread 01 8.00 (203.2) 2.00 (50.8) 2.000 (50.80) 1.250 (31.75) 1.250 (31.75) .375 (9.53) 8.375 (212.73) .164-32 UNC-2B .164-32 UNC-2B 02 8.00 (203.2) 3.25 (82.6) 2.062 (52.37) 1.250 (31.75) 2.500 (63.50) .375 (9.53) 8.375 (212.73

16、) .164-32 UNC-2B .190-32 UNC-2B 03 12.00 (304.8) 3.25 (82.6) 2.062 (52.37) 1.250 (31.75) 2.500 (63.50) .375 (9.53) 12.375 (314.33) .164-32 UNC-2B .190-32 UNC-2B 04 12.00 (304.8) 3.25 (82.6) 2.500 (63.50) 1.750 (44.45) 2.500 (63.50) .375 (9.53) 12.375 (314.33) .190-32 UNC-2B .190-32 UNC-2B 05 12.00 (

17、304.8) 3.00 (76.2) 3.000 (76.20) 2.250 (57.15) 2.250 (57.15) .375 (9.53) 12.375 (314.33) .250-20 UNC-2B .190-32 UNC-2B Dash No. K Dia. Max L .015 (.38) M .062 (1.57) N .0075 (0.19) P Max R Min S T Weight (lbs) Max 01 .562 (14.27) 1.250 (31.75) .562 (14.27) 0.625 (15.88) .690 (17.53) .290 (7.37) .281

18、 (7.14) .750 (19.05) 2.6 02 .562 (14.27) 2.250 (57.15) .562 (14.27) 0.625 (15.88) .690 (17.53) .290 (7.37) .281 (7.14) .750 (19.05) 3.8 03 .562 (14.27) 2.250 (57.15) .562 (14.27) 0.625 (15.88) .690 (17.53) .290 (7.37) .281 (7.14) .750 (19.05) 6.0 04 .687 (14.45) 2.250 (57.15) .562 (14.27) 0.875 (22.

19、23) .690 (17.53) .290 (7.37) .281 (7.14) .750 (19.05) 6.7 05 .875 (22.23) 2.250 (57.15) .687 (17.45) 1.125 (28.58) 1.25 (31.6) .600 (15.24) .281 (7.14) .750 (19.05) 7.7 FIGURE 1. Case dimensions and circuit diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

20、 from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 83006 REV E PAGE 4 Hardware A .005 (.13) B .005 (.13) C .010 (.25) D .005 (.13) Thread size .330 (8.38) .020 (.51) .344 (8.74) .125 (3.18) .164-32 UNC-2B .375 (9.53) .022 (.56) .375 (9.53) .125 (3.18) .

21、190-32 UNC-2B .472 (11.99) .025 (.64) .437 (11.10) .156 (3.96) .250-32 UNC-2B NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Circuit diagram is for information only. 4. Mounting hardware shall be supplied with filter. 5. Terminal hardware shall b

22、e supplied with filter. 6. Recommended mounting torque 192 oz-in maximum. 7. Recommended terminal torque as follows: FIGURE 1. Case dimensions and circuit diagram - Continued. Thread Torque .164-32 UNC-2A 64 oz-in max. .190-32 UNF-2A 96 oz-in max. .250-20 UNC-2A 192 oz-in max. Provided by IHSNot for

23、 ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 83006 REV E PAGE 5 3.5 Electrical characteristics. 3.5.1 Rated voltage. The rated voltage shall be 115 volts ac from dc to 400 Hertz. 3.5.2

24、Rated current. See table I. 3.5.3 Insertion loss. Insertion loss shall be in accordance with MIL-STD-220, at 25C (see table I). 3.5.4 Dielectric withstanding voltage. Dielectric withstanding voltage shall be in accordance with MIL-PRF-15733. 3.5.5 Insulation resistance. The insulation resistance of

25、the filter shall be 1,000 megohms minimum. 3.5.6 Voltage drop. The voltage drop shall be 1.15 volts ac (rms) maximum. 3.5.7 Capacitance to ground. Not applicable. 3.6 Environmental and mechanical requirements. The environmental and mechanical requirements shall be in accordance with MIL-PRF-15733. T

26、he following details and exceptions shall apply. 3.6.1 Terminal strength. Terminal strength shall be in accordance with MIL-PRF-15733 and method 211 of MIL-STD-202, test condition E. TABLE I. Electrical characteristics. Dash no. 83006- Rated current (amps) ac (rms) or dc Minimum insertion loss (dB)

27、in accordance with MIL-STD-220 1/ At +25C 14 kHz 20 kHz 50 kHz 150 kHz 300 kHz 600 kHz 1 MHz 10 MHz 100 MHz 1 GHz 10 GHz 01 5 40 48 64 80 80 80 80 80 80 80 80 02 10 40 48 64 80 80 80 80 80 80 80 80 03 20 40 48 64 80 80 80 80 80 80 80 80 04 30 40 48 64 80 80 80 80 80 80 80 80 05 50 40 48 64 80 80 80

28、80 80 80 80 80 1/ Full-load insertion loss measurements shall be performed at frequencies between 100 kHz and 20 MHz inclusive; all other measurements shall be performed at no-load. 3.6.2 Salt spray (corrosion). Salt spray (corrosion) shall be in accordance with MIL-PRF-15733 and method 101 of MIL-S

29、TD-202, test condition B. 3.6.3 Shock (specified pulse). Shock shall be in accordance with MIL-PRF-15733 and method 213 of MIL-STD-202, test condition I. 3.6.4 Vibration, low frequency. Vibration shall be in accordance with MIL-PRF-15733 and method 201 of MIL-STD-202; low frequency vibration test on

30、ly. 3.7 Marking. The marking shall include the PIN as specified in 1.2, the manufacturers name or code, date code, voltage rating, current rating, and circuit diagram. 3.8 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the Qual

31、ified Products List for MIL-PRF-15733/2, /41, /55, /65, or /75 for at least one part or, perform first article inspection in accordance with the MIL-PRF-15733 qualification inspection requirements. 3.9 Certificate of compliance. A certificate of compliance shall be required from manufacturers reques

32、ting to be an approved source of supply. 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requireme

33、nts, and promotes economically advantageous life cycle costs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 83006 REV E PAGE 6 3.11 Workmanship. Filters shall be pr

34、ocessed in such a manner as to be uniform in quality and shall be free from cold soldering, corrosion, pits, dents, cracks, rough or sharp edges, misalignments, and other defects that will affect life, serviceability, or appearance. Cracks in glass seals are not allowed; however, minor meniscus craz

35、ing is acceptable. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of groups A and C inspections of MIL-PRF-15733. 4.2.2 Certification. The a

36、cquiring activity, at its discretion, may accept a certificate of compliance with group C requirements in lieu of performing the group C tests (see 6.2c). 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When a

37、ctual packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within th

38、e Military Department or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This se

39、ction contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Filters conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not

40、 available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing on QPL-15733, t

41、his drawing becomes obsolete and will not be used for new design. The QPL-15733 product shall be the preferred item for all applications. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery, and one copy of the confo

42、rmance inspection data or certificate of compliance with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the group C tests or provides certification of compliance with group C requirements. d. Requirements for notification of change of product to acquiring activity i

43、f applicable. e. Requirements for packaging and packing. 6.3 Replaceability. Filters covered by this drawing will replace the same commercial device covered by contractor-prepared specification or drawing. 6.4 Pure tin prohibition. Pure tin is prohibited since it may result in tin whisker growth. Th

44、e use of alloys with tin content greater than 97 percent may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions on products that use such materials. Conformal coatings applied

45、over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coating of Tin). Provide

46、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 83006 REV E PAGE 7 6.5 Users of record. Military and industrial users of this drawing should inform DLA Land and Maritime whe

47、n a system application requires configuration control. DLA Land and Maritime-VAT will maintain a record of users and this list will be used for coordination and distribution of changes to this drawing. Coordination of this document for future revisions is coordinated only with the sources of supply

48、and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990, by facsimile at (614) 693-1644, or by e-mail to capacitorfilterdla.mil. 6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990, by telephone (614-692-4709), or