DLA DSCC-DWG-13014 REV A-2013 ATTENUATORS FIXED COAXIAL LINE (SMA CONNECTORS) FREQUENCY RANGE DC TO 12 4 GHz CLASS IV LOW POWER.pdf

《DLA DSCC-DWG-13014 REV A-2013 ATTENUATORS FIXED COAXIAL LINE (SMA CONNECTORS) FREQUENCY RANGE DC TO 12 4 GHz CLASS IV LOW POWER.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-13014 REV A-2013 ATTENUATORS FIXED COAXIAL LINE (SMA CONNECTORS) FREQUENCY RANGE DC TO 12 4 GHz CLASS IV LOW POWER.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Update paragraph 3.7 26 September 2013 Michael A. Radecki Prepared in accordance with ASME Y14.100 REV STATUS REV A A A A A A OF PAGES PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Yeasvina Afroz DESIGN ACTIVITY DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Origin

2、al date of drawing 15 March 2013 CHECKED BY Yeasvina Afroz TITLE ATTENUATORS, FIXED, COAXIAL LINE (SMA CONNECTORS), FREQUENCY RANGE: DC TO 12.4 GHz, CLASS IV, LOW POWER APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 13014 SCALE N/A REV A PAGE 1 OF 6 AMSC N/A 5985-2013-E07Provide

3、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13014 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for fixed coaxial line (series S and N) attenuators scree

4、ned to MIL-DTL-3933. The attenuators described herein are direct replacements for screened (S) and non-screened (N) MIL-DTL-3933/14 attenuators that lost their qualified MIL-DTL-3933 source (see 6.4 and table II). 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 13014 -13N

5、 Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information

6、 or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifi

7、cations, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-D

8、TL-3933 - Attenuators, Fixed, Space Level, Non-Space Level, General Specification for. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence.

9、 Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and reg

10、ulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-DTL-3933 and herein (see figure 1). 3.1.1 Pure tin. The use of pure tin, as an underplate or final finish is prohibited bo

11、th internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.2 Rated temperature. -55C to +125C. 3.3 Maximum weight. 0.8 ounces. Provided by IHSNot for ResaleNo reproduct

12、ion or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13014 REV A PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Metric equivalents are in parentheses. FIGURE 1. D

13、imensions and configuration. 3.4 Electrical characteristics. 3.4.1 Nominal impedance. 50 ohms. 3.4.2 Attenuation: See table I. Stability and sensitivity: Frequency sensitivity, maximum: 0.4 dB/dB/GHz. Temperature sensitivity of attenuation, maximum: 0.0006 dB/dB/C. 3.4.3 Power. See table I. Power se

14、nsitivity for full input power, maximum: 0.005 dB/dB/Watt. 3.4.4 VSWR. See table I. 3.4.5 Connector repeatability. Maximum variation in attenuation: 0.04 dB. 3.5 Engineering data. 3.5.1 Operating frequency range. DC to 12.4 GHz. 3.5.2 Test frequency range. 3.5.2.1 For VSWR and attenuation measuremen

15、ts, measured or recorded, when using an Automatic Network Analyzer (ANA) or equivalent test equipment: 100 MHz (or lower) to 12.4 GHz. 3.5.2.2 Basic test frequency for sensitive measurements like connector repeatability, temperature sensitivity, power sensitivity and any other measurements where a d

16、elta specification is imposed: 6.0 GHz Maximum attenuation change after: Up to 10 dB, inclusive (dB) Over 10 dB (dB/dB) Temperature change / thermal shock 0.5 0.05 Vibration or shock 0.5 0.05 Moisture resistance or salt spray 0.5 0.05 Peak power 0.5 0.05 Provided by IHSNot for ResaleNo reproduction

17、or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13014 REV A PAGE 4 TABLE I. Electrical characteristics. Dash number Attenuation (dB) Maximum power Input at 25C VSWR maximum 1/ Weight (oz) Maximum Dimension A (inches) Maxim

18、um Nominal Deviation DC to 4.0 GHz 4.0 to 8.0 GHz 8.0 to 12.4 GHz DC to 12.4 GHz AV (W) 3/ (continuously) Peak 2/ (kW) 13 N S 30 0.9 2 0.2 1.15:1 1.20:1 1.25:1 0.8 1.850 (46.99) 14 N S 40 0.9 2 0.2 1.15:1 1.20:1 1.25:1 0.8 1.850 (46.99) 1/ VSWR value is for both ends. 2/ Peak power for a duty cycle

19、of 5 x 10-4 ;maximum pulse duration 5 microseconds. 3/ Power input is derated linearly to 0.5 watts at +125C. 3.6 Marking. In accordance with MIL-DTL-3933, except the attenuator shall be marked with the PIN as specified herein (see 1.2). 13014-13N - Drawing PIN 12345 - Manufacturers source code or l

20、ogo 1305 - Date code XXXX - Serialization 3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-DTL-3933 Qualified Products Database for at least one part or was previously listed, or provide evidence that their parts have

21、 passed the group A inspections, Screening (when applicable) and material specified in MIL-DTL-3933. 3.8 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.9 Recycled, recovered, or environmentally preferable m

22、aterials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.10 Workmanship. The attenuator sha

23、ll be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. For N level product, inspection of pr

24、oduct for delivery shall consist of the group A inspection of MIL-DTL-3933. For S level product, inspection of product for delivery shall consist of screening and the group A inspection of MIL-DTL-3933. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as spec

25、ified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Poin

26、ts packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packagi

27、ng activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13014 REV A PAGE 5 6. NOTES (This section contains information of a general or explanatory nature which may be helpf

28、ul, but is not mandatory.) 6.1 Intended use. Attenuators conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to pre

29、vent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The

30、 contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements

31、 for notification of change of product to the acquiring activity, if applicable. d. Requirements for packaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur a

32、nytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibi

33、t the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 MIL-DTL-3933/14 replacements. The attenuators described herein are direct replacements for some of the MIL-DTL-3933/14 attenuators. TABLE II.

34、 Replacement data. MIL-DTL-3933/14 PIN DLA Land and Maritime drawing PIN 13014- M3933/14-13N 13N M3933/14-13S 13S M3933/14-14N 14N M3933/14-14S 14S 1/ M3933 non-screened (N) PINs may also be known without the ending N character. 6.5 Replaceability. Attenuators covered by this drawing will replace th

35、e same commercial device covered by contractor prepared specification or drawing. 6.6 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where modifications from this revision were made. This was done as a convenience only and the Government ass

36、umes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations 6.7 Users of record. Coordination of this document for future revisions is coor

37、dinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to tubesampsdla.mil, or by telephone (

38、614) 692-0551 or DSN 850-0551. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13014 REV A PAGE 6 6.8 Approved sources of supply. Approved sources of supply are listed herein. A

39、dditional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to tubesampsdla.mil, or by telephone (614) 692-0551 or DSN 850-0551. DLA Land and Maritime drawing PI

40、N Vendor Vendor CAGE Vendor name and address Similar designation 1/ 13N 13S 14N 14S A 34078 Emerson Network Power Connectivity Solutions 299 Johnson Avenue Waseca, MN 56093 ATT-205 Series 13N 13S 14N 14S B 95077 SV Microwave 2400 Centrepark West Drive Suite 100 West Palm Beach, FL 33409-6469 SF0929-6810-XXX 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-