DLA DSCC-DWG-13013 REV A-2013 ATTENUATORS FIXED COAXIAL LINE (SERIES N) FREQUENCY RANGE DC TO 18 GHz CLASS III MEDIUM POWER.pdf

《DLA DSCC-DWG-13013 REV A-2013 ATTENUATORS FIXED COAXIAL LINE (SERIES N) FREQUENCY RANGE DC TO 18 GHz CLASS III MEDIUM POWER.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-13013 REV A-2013 ATTENUATORS FIXED COAXIAL LINE (SERIES N) FREQUENCY RANGE DC TO 18 GHz CLASS III MEDIUM POWER.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new approved sources and correct scope from “possible replacements” to “direct replacements”. 2 April 2013 Michael A. Radecki Prepared in accordance with ASME Y14.100 REV STATUS REV A A A A A A OF PAGES PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Michael A.

2、Radecki DESIGN ACTIVITY DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Original date of drawing 19 February 2013 CHECKED BY John Bonitatibus TITLE ATTENUATORS, FIXED, COAXIAL LINE (SERIES N), FREQUENCY RANGE: DC TO 18 GHz, CLASS III, MEDIUM POWER APPROVED BY Robert M. Heber SIZE A CODE IDENT. NO. 037

3、Z3 DWG NO. 13013 SCALE N/A REV A PAGE 1 OF 6 AMSC N/A 5985-2013-E05Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13013 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing describes

4、the requirements for fixed coaxial line (series N) attenuators screened to MIL-DTL-3933. The attenuators described herein are direct replacements for non-screened (N) MIL-DTL-3933/10 attenuators (see 6.4 and table II). 1.2 Part or Identifying Number (PIN). The complete PIN will be in the following f

5、orm: 13013 -02 Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, and 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for addi

6、tional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, and 5 of this specification, whether or not they are listed. 2.2 Government do

7、cuments. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENS

8、E SPECIFICATIONS MIL-DTL-3933 - Attenuators, Fixed, Space Level, Non-Space Level, General Specification for. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or from the DLA Document Service Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.

9、) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersed

10、es applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-DTL-3933 and herein (see figure 1). 3.1.1 Pure tin. The use of pure tin, as an underplate or fin

11、al finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.2 Rated temperature. -55C to +125C. 3.3 Maximum weight. 6 ounces. Provided by IHSNo

12、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13013 REV A PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Metric equivalents are in

13、parentheses. FIGURE 1. Dimensions and configuration. 3.4 Electrical characteristics. 3.4.1 Nominal impedance. 50 ohms. 3.4.2 Attenuation. Frequency sensitivity, maximum: 0.1 dB/dB/GHz. Temperature sensitivity of attenuation, maximum: 0.0004 dB/dB/C. 3.4.3 Power. See table I. Power sensitivity for fu

14、ll input power, maximum: 0.005 dB/dB/Watt. 3.4.4 VSWR. See table I. 3.4.5 Connector repeatability. Maximum variation in attenuation: 0.02 dB. 3.5 Engineering data. 3.5.1. Operating frequency range. DC to 11 gigahertz (GHz) (see table I). Maximum attenuation change after: Up to 10 dB, inclusive (dB)

15、Over 10 dB (dB/dB) Temperature change/ thermal shock 0.05 0.005 Vibration or shock 0.1 0.01 Moisture resistance or salt spray 0.2 0.02 Peak power 0.05 0.005 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A C

16、ODE IDENT NO. 037Z3 DWG NO. 13013 REV A PAGE 4 3.5.2 Test frequency range. 3.5.2.1 For VSWR and attenuation measurements, measured or recorded, when using an Automatic Network Analyzer (ANA) or equivalent test equipment: 100 MHz (or lower) to Dash numbers 4 GHz 02 through 05 8 GHz 09 through 10 11 G

17、Hz 13 through 14 TABLE I. Electrical characteristics. Dash number Attenuation (dB) Maximum power Input VSWR maximum 1/ Nominal Deviation DC to 4.0 GHz 4.0 to 6 GHz 4.0 to 8.0 GHz 6.0 to 11 GHz DC to 4.0 GHz DC to 6 GHz DC to 8 GHz DC to 11GHz DC to 12 GHz DC to 18.0 GHz AV (W) at 25C (continuously)

18、Peak (kW) 02 3 0.5 - - - - - 20 4/ 1 3/ 1.15:1 - - - 04 20 0.5 - - - - - 20 4/ 1 3/ 1.15:1 - - - 05 30 0.75 - - - - - 20 4/ 1 3/ 1.15:1 - - - 09 20 0.3 - 0.6 - - - 25 5/ 5 2/ 1.20:1 - 1.30:1 - 10 30 0.6 - 1.0 - - - 25 5/ 5 2/ 1.20:1 - 1.30:1 - 13 10 0.35 0.65 - 0.75 - - 20 4/ 1 2/ 1.15:1 1.20:1 - 1.

19、30:1 14 20 0.35 0.65 - 0.75 - - 20 4/ 1 2/ 1.15:1 1.20:1 - 1.30:1 1/ VSWR value is for both ends. 2/ Peak power for a duty cycle of 5 x 10-4maximum duration 5 microseconds. 3/ Peak power for a duty cycle of 1 x 10-3 maximum duration 5 microseconds. 4/ Derate linearly from 20 watts at 25C to 10 perce

20、nt at 125C. 5/ Derate linearly from the stated watts at 25C to 0 watts at 125. 3.6 Marking. In accordance with MIL-DTL-3933, except the attenuator shall be marked with the PIN as specified herein (see 1.2). 13013-02 - Drawing PIN 12345 - Manufacturers source code or logo 1133 - Date code XXXX - Seri

21、alization 3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-DTL-3933 Qualified Products Database for at least one part, or provide evidence that their parts have passed the qualification requirements of MIL-DTL-3933. 3

22、.8 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.9 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum e

23、xtent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZ

24、E A CODE IDENT NO. 037Z3 DWG NO. 13013 REV A PAGE 5 3.10 Workmanship. The attenuator shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance ins

25、pection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A inspection of MIL-DTL-3933. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of

26、materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defen

27、se Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of

28、a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Attenuators conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM applic

29、ation. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will

30、not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each ship

31、ment of parts by the manufacturer. c. Requirements for notification of change of product to the acquiring activity, if applicable. d. Requirements for packaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth pr

32、oblems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloy

33、s of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

34、-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13013 REV A PAGE 6 6.4 MIL-DTL-3933/10 replacements. The attenuators described herein are direct replacements for MIL-DTL-3933/10 non-screened attenuators. TABLE II. Replacement data. MIL-DTL-3933/10 PIN DLA Land and Maritim

35、e drawing PIN 13013- M3933/10-02N 02 M3933/10-04N 04 M3933/10-05N 05 M3933/10-09N 09 M3933/10-10N 10 M3933/10-13N 13 M3933/10-14N 14 1/ M3933 PINs may also be known without the ending N character. 6.5 Replaceability. Attenuators covered by this drawing will replace the same commercial device covered

36、 by contractor prepared specification or drawing. 6.6 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for

37、any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. 6.7 Users of record. Coordination of this document for future revis

38、ions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to tubesampsdla.mil, or by

39、 telephone (614) 692-0551 or DSN 850-0551. 6.8 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH

40、43218-3990, by email to tubesampsdla.mil, or by telephone (614) 692-0551 or DSN 850-0551. Vendor Vendor CAGE Vendor name and address Similar designation 1/ A 93459 Aeroflex/Weinschel Corporation 276N Series 5305 Spectrum Drive Fredrick, MD 21703-7339 B 95077 SV Microwave 2400 Centrepark West Drive Suite 100 West Palm Beach, FL 33409-6469 SF0965-0209-XX 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-