DLA AN103501 THRU AN103600 REV 3-1986 BOLT - DRILLED HEX HEAD 1 HOLE 625-18.pdf

《DLA AN103501 THRU AN103600 REV 3-1986 BOLT - DRILLED HEX HEAD 1 HOLE 625-18.pdf》由会员分享，可在线阅读，更多相关《DLA AN103501 THRU AN103600 REV 3-1986 BOLT - DRILLED HEX HEAD 1 HOLE 625-18.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、,637 I FE. SUP. CLASS L 1.250 1.312 1.375 1 .U38 1.500 1.562 1.625 1.688 1.750 1.812 1.875 5306 LLL K TO FULL THD .O16 OR CHAMFE _- SPEC MIL-S-774 K t .o00 - .o60 iii lil . ,SB .250 .312 .375 (e) THREAD 1 SECTION THRU THRI 1.938 2.000 2.062 AN103510 1 2.375 AN103511 1 2.438 AN103512 1 2.500- AN10351

2、 2.625 AN103512 I 2.750 AN103515 2.875 AN103516 I 3.000 HEAD. HAXIHUH Ti K +.o00 - .o60 .438 .500 .562 .625 .688 .750 .a12 .a75 .938 1.000 1.125 1.250 1.375 1.500 _ _- . -THIS SURFACE MUST BE SQUARE WITH SHANK WITHIN ,003 FIR. H HAM FER 30 TO .938 DIA (OPPOSITE SIDE OPTIONAL) E AN103525 4.125 AN1035

3、26 4;250 AN103527 4.375 AN103528 4.500 AN103524 4.625 - ._ - . _ 1 _ 4.750 AN103530 IMPERFECT THREADS K +.OW - .o60 1.625 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 II PART NO.11 L AN103531 4.875 AN103532 I I 5.000 AN103533 5.125 AN103534 i 5.250 AN103535 5.375 AN1

4、03536 I I 5.500 AN103543 AN103544 I/ K ?-+.O00 PART NO. - .o60 3.375 AN103545 3.625 3.500 AN103546 AN103547 i :g?g AN103548 AN103549 ,000. AN103550 4.125 AN103551 4.250 AN103552 4 I 375 AN103553 4.500 AN103554 NOTE: (1) SHANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCEN

5、TRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK LN RELATION TO THE WASHER FACE DIAMETER AND HEXAGON SHALL BE WITHIN .O28 FIR. HATERIAL: STEEL AHS632 HARDNESS: ROCKUELL C76 - 32 FINISH: CADHIUH PLATE AUS2400 SURFACE ROUGHNESS: AS107 MANUFACTU

6、RING SPECIFICATION: AUS7452 ) INSPECTION: ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCORDANCE WITH At(S2640. BREAK SHARP EDGES .O03 - .O15 UNLESS OTHERWISE SPECIFIED. DIHENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERENCES; LINEAR DIHENSIONS 2.010, ANGULAR DIHENSIONS 22. DO NOT USE UNASSI

7、GNED PART NUHBERS. INACTIVE FOR NEW DESIGN AFTER 3 MARCH 1969 NO SUPERSEDING STANDARD. THIS STANDARD WAS DEVELOPED COOPERATIVELY 8Y THE ENGINE AND PROPELLER UTILITY PARTS COMHITTEE OF THE SAE. AIR FORCE-NAVY AERONAUTICAL STANDARD AN i03501 ,A. Ar-II THRU BOLT - DRILLED HEX KEAD, 1 HOLE, .625-18 A Ni03600 :UST. NAVY-AS ARMY-AV Project No. 5306-1020 f THIS DOCUMENT CONTAINS PAGES. - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-