DLA A-A-59617-2002 UNIONS BRASS OR BRONZE THREADED PIPE CONNECTIONS AND SOLDER-JOINT TUBE CONNECTIONS《带螺纹的铜管接头和钎焊缝软管接头》.pdf

《DLA A-A-59617-2002 UNIONS BRASS OR BRONZE THREADED PIPE CONNECTIONS AND SOLDER-JOINT TUBE CONNECTIONS《带螺纹的铜管接头和钎焊缝软管接头》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59617-2002 UNIONS BRASS OR BRONZE THREADED PIPE CONNECTIONS AND SOLDER-JOINT TUBE CONNECTIONS《带螺纹的铜管接头和钎焊缝软管接头》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUND A-A-59617 22 April 2002 SUPERSEDING WW-U-516B 29 August 1974 COMMERCIAL ITEM DESCRIPTION UNIONS, BRASS OR BRONZE, THREADED PIPE CONNECTIONS AND SOLDER-JOINT TUBE CONNECTIONS The General Services Administration has authorized the use of this commercial item description (CID) for all feder

2、al agencies. 1. SCOPE. This CID covers the general requirements for brass or bronze unions with threaded pipe or solder-joint tube connections for joining nonferrous pipe and tubing. The unions covered by this CID, which are intended for commercial/industrial applications, are compatible with standa

3、rd weight copper or brass pipe, copper water tube, cast bronze threaded fittings, cast bronze solder-joint pressure fittings, and wrought copper and bronze solder-joint pressure fittings. 2. CLASSIFICATION. This CID uses a classification system that is included in the Part Identification Number (PIN

4、) as shown in the following example (see 7.1). AA59616 XX CID Type/Style/Size Code Number Number (see 2.1) 2.1 Type, style, and size. The type, style, and size of unions is identified by a two-digit code number that indicates application characteristics (see Table I). Type I - Cast Brass or Bronze,

5、Threaded Pipe Ends, Class 125 Style A - Female pipe thread to female pipe thread Style B - Female pipe thread to male pipe thread Type II - Cast Brass or Bronze, Threaded Pipe Ends, Class 250 Style A - Female pipe thread to female pipe thread Style B - Female pipe thread to male pipe thread AMSC N/A

6、 FSC 4730 DISTRIBUTION STATEMENT A. Approved for public release: distribution is unlimited. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other data that may improve this document should be sent to: Defense Supply Center, Columbus, ATTN: DSCC-VAI, P.O. Box

7、3990, Columbus, OH 43216-5000, or telephone (614) 692-0538, or facsimile (614) 692-6939. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59617 2 Type III - Cast Bronze, Wrought Copper or Wrought Bronze, Solder-Joint Tube Ends Style A - Female tub

8、e to female tube Style B - Female tube to male tube Type IV - Cast Bronze, Wrought Copper or Wrought Bronze, Solder-Joint Tube End to Threaded Pipe End Style A - Female tube to female threaded pipe Style B - Female tube to male threaded pipe Table I. Union characteristic designators. Type I Type II

9、Type III Type IV Style Style Style Style Style Style Style Style Union size (inch) A B A B A B A B 0.125 01 02 03 04 05 06 07 08 0.250 09 10 11 12 13 14 15 16 0.375 17 18 19 20 21 22 23 24 0.500 25 26 27 28 29 30 31 32 0.750 33 34 35 36 37 38 39 40 1.000 41 42 43 44 45 46 47 48 1.250 49 50 51 52 53

10、54 55 56 1.500 57 58 59 60 61 62 63 64 2.000 65 66 67 68 69 70 71 72 2.500 73 74 75 76 77 78 79 80 3.000 81 82 83 84 85 86 87 88 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Unions supplied to this CID shall be as specified herein. 3.2 Materials. 3.2.1 Type I and II unions. Mat

11、erials shall be Copper Alloy UNS C83600, UNS C83800 or UNS C84400 (see 7.8). 3.2.2 Type III and IV cast bronze unions. Materials shall be Copper Alloy UNS C83600, UNS C83800 or C84400 (see 7.8). 3.2.3 Type III and IV wrought copper or wrought bronze unions. Materials shall be not less than 83 percen

12、t copper content or shall be Copper Alloy UNS C83600 (see 7.8). 3.3 Metal thickness. The metal thickness of the unions shall be as specified in table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59617 3 Table II. Metal Thickness. 1/, 2/ Ca

13、st Wrought Union Bodies Solder cups size Type I, III, and IV Type II Type III and IV Type III and IV 0.125 0.08 0.10 0.05 0.022 0.250 0.08 0.11 0.05 0.026 0.375 0.09 0.12 0.05 0.031 0.500 0.09 0.13 0.05 0.036 0.750 0.10 0.16 0.06 0.041 1.000 0.11 0.17 0.07 0.046 1.250 0.12 0.19 0.07 0.050 1.500 0.13

14、 0.20 0.08 0.055 2.000 0.15 0.22 0.09 0.064 2.500 0.17 0.24 0.10 0.074 3.000 0.19 0.26 0.11 0.083 1/ Dimensions are in inches. 2/ Thicknesses are nominal; at no point shall the thickness be less than 90% of the thickness given. 3.4 End connections. Threaded end connections of Type I, II, and IV unio

15、ns shall have right hand threads in accordance with the style of union. Minimum useful thread lengths shall be as specified in Table III; otherwise, threads shall meet the National Pipe Thread (NPT) requirements of ANSI/ASME B1.20.1. Solder-joint tube ends of Type III and IV unions shall meet the di

16、mensional characteristics specified in Table III. 3.5 Flow diameter. At no point within the unions shall the flow diameter be less than the dimensions specified in Table III. 3.6 Size. The size of the unions are identified by the nominal size as listed in Table III. Threaded pipe connections corresp

17、ond to “nominal pipe size“ and solder-joint tube connections correspond to “standard water tube size“. 3.7 Union connections. The threads for the union connection shall be in accordance with the manufacturers standard practice. 3.8 Seating. Seating joints shall be ball type or ball-to-cone type. 3.9

18、 Pressure surfaces. All surfaces subject to pressure in the tightening of the unions shall be finished smooth and true to insure proper seating of component parts. 3.10 Finish. When cast unions are furnished, finish shall be as cast. 3.11 Wrench surfaces. Wrench surfaces shall be provided on all com

19、ponents having a thread. The wrench surfaces may be a polygon, two opposing flatted surfaces, or a round surface with no less than two ribs raised above the surface controlling the minimum wall thickness. Nuts shall have a polygon wrench surface. Provided by IHSNot for ResaleNo reproduction or netwo

20、rking permitted without license from IHS-,-,-A-A-59617 4 Table III. Union characteristics. 1/ Thread Tensile length Male solder-joint Female solder-joint strength Union on Outside Inside Cup Flow testing size ends diameter Length diameter depth diameter force Pounds, Min Min Max Min Min Max Min Min

21、Min 0.125 0.250 0.249 0.251 0.375 0.253 0.255 0.312 0.180 1,000 0.250 0.320 0.374 0.376 0.385 0.378 0.380 0.312 0.300 1,400 0.375 0.360 0.499 0.501 0.437 0.503 0.505 0.375 0.390 2,000 0.500 0.430 0.624 0.626 0.562 0.628 0.630 0.500 0.520 3,600 0.750 0.500 0.874 0.876 0.812 0.878 0.880 0.750 0.740 5,

22、500 1.000 0.580 1.124 1.127 0.968 1.128 1.131 0.906 0.980 6,800 1.250 0.670 1.374 1.377 1.031 1.378 1.381 0.968 1.230 8,900 1.500 0.700 1.623 1.627 1.156 1.629 1.632 1.093 1.470 11,000 2.000 0.750 2.123 2.127 1.406 2.129 2.132 1.343 1.940 14,000 2.500 0.920 2.623 2.627 1.531 2.629 2.632 1.468 2.380

23、20,000 3.000 0.980 3.123 3.127 1.718 3.129 3.132 1.656 2.890 23,000 1/ Dimensions are in inches. 3.12 Performance. The unions covered by this CID shall be compatible with standard weight copper or brass pipe and copper water tube conforming to ASTM B 88, cast bronze threaded fittings conforming to A

24、NSI/ASME B16.15, cast bronze solder-joint pressure fittings conforming to ASME B16.18, and wrought copper and bronze solder-joint pressure fittings conforming to ASME B16.22. 3.12.1 Leakage. All unions shall be capable of withstanding an air pressure of at least 60 pounds per square inch gage (PSIG)

25、 or hydrostatic pressure of not less than 250 PSIG without leakage while under water. 3.12.2 Tensile strength. The unions shall exhibit tensile properties in Table III. 3.13 Workmanship. All parts shall be clean, free of fins, and be sound, smoothly cored, true to form, and uniform in texture and st

26、rength. There shall be no cold shuts, porosity, or any other defects that may affect serviceability. Repair processes, such as plugging or filling with cold solder, shall not be permitted. 3.14 Marking. Unions supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN

27、. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

28、IHS-,-,-A-A-59617 5 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the

29、 commercial market. The Government reserves the right to require proof of such conformance. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See s

30、ection 2 for PIN format example. 7.2 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these unions to DSCC under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.3 Source of documents. Fed

31、eral Regulations FEDERAL ACQUISITION REGULATION (FAR) FAR PARA. 23.403 - Federal Acquisition Regulations (Application for copies should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-0001.) Other Publications AMERICAN SOCIETY OF MECHANICAL ENGI

32、NEERS (ASME) ANSI/ASME B1.20.1 - Pipe Threads, General Purpose (Inch) ANSI/ASME B 16.15 - Cast Bronze Threaded Fittings Classes 125 and 250 ASME B16.18 - Cast Copper Alloy Solder Joint Pressure Fittings ASME B16.22 - Wrought Copper and Copper Alloy Solder Joint Pressure Fittings (Application for cop

33、ies should be addressed to the American Society of Mechanical Engineers, 345 East 47th Street, New York, NY 10017.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM B 88 - Standard Specification for Seamless Copper Water Tube (Application for copies should be addressed to the American Society

34、for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) (Industry association specifications and standards are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.)Provided by IHSNot for ResaleNo r

35、eproduction or networking permitted without license from IHS-,-,-A-A-59617 6 7.4 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN b. Product conformance provisions c. Packaging requirements 7.5 Commercial products. As part of the market

36、 analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE: This information should no

37、t be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) MFRs CAGE MFRs Name and Address MFRs CAGE MFRs Name and Address 03670 Ansul Inc. 79500 Westinghouse Electric Group 1 Stanton Street 11 Stanwix Street Marinettte, WI 54143 Pittsbur

38、gh, PA 15222 Phone number: 1-715-735-7411 Phone number: 1-412-256-1000 05869 Raytheon Co. 97942 Northrup Grumman Corporation 3310 1901 W. Malvern Avenue 1580 W. Nursery Road A Fullerton, CA 92834 Lithicum Heights, MD 21090-7632 Phone number: 1-714-732-3597 Phone number: 1-410-765-7632 12168 Northern

39、 Indiana Business Svc (NIBCO) 26512 Northrup Grumman Corporation 1167 52777 Winding Waters Lane S. Oyster Bay Road Elkhart, IN 46516 Bethpage, NY 11714 Phone number: 1-219-295-3000 Phone number: 1-516-346-7086 050R4 Patriot Valve and Fitting Corp. 0RVB7 Westwater Supply-Springfield Inc. 298B Montros

40、e Road 30 Walnut Street Westbury, NY 11590 Springfield, OH 45501 Phone number: 1-516-333-8430 Phone number: 1-513-325-2434 Fax number: 1-516-333-8774 1BS72 C.W. Supply Inc. 03958 Mindeco Corp. 661 W. Vine Street 3345 Royal Avenue Salt Lake City, UT 84123 Oceanside, NY 11572 Phone number: 1-801-261-4

41、922 Phone number: 1-516-678-4301 Fax number: 1-801-261-5441 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59617 7 MFRs MFRs Name and Address MFRs MFRs Name and Address CAGE CAGE 41947 Mueller Brass 4M357 Lin-Fasteners Inc. 2199 Laper Avenue 770

42、 S. Rt. 73 Port Huron, MI 48061 West Berlin, NJ 08091 Phone number: 1-800-553-3336 Phone number: 1-856-768-2320 Fax number: 1-856-767-0949 5A784 Southeastern Sales Co. Springfield, OH 45501 61096 Alchrome Products Co. 98 Elizabeth Street 65430 Standard Nipple Works Inc. Newcomerstown, OH 43832 15 No

43、rth Avenue Phone number: 1-614-498-7202 Garwood, NJ 07027 Phone number: 1-908-789-4747 66200 Pioneer Industries Inc. 93 Seigel Street 6Z024 Sunbury Supply Co. Brooklyn, NY 11206 Sunbury, OH 43074 Phone number: 1-718-387-4724 Phone number: 1-614-965-3133 Fax number: 1-718-387-2345 91050 Woodward-Wang

44、er Co. 84849 Levine Samuel Plumbing and 5301 Tacony Street Heating Supplies Inc. Philadelphia, PA 19137 283 W. Broadway Phone number: 1-215-535-4600 New York, NY 10013 Fax number: 1-215-535-3309 Phone number: 1-212-431-6760 Fax number: 1-212-925-8249 04BQ9 VJ Supply Inc. 838 Sussex Blvd., 2nd Floor

45、9M105 A Better Way Inc. Broomall, PA 19008 401-A N. Poplar Avenue Phone number: 1-610-604-4447 Waynesboro, VA 22980 Fax number: 1-610-604-4448 Phone number: 1-540-949-7640 Fax number: 1-540-949-7643 8A440 New England Union Co. Inc. 70 Hay Street 0BGU9 A Z E Supply Co. Inc. West Warwick, RI 02893 18

46、Rockhill Road Phone number: 1-401-821-0800 Bala Cynwyd, PA 19004 Phone number: 1-610-667-3406 0APY9 Wisconsin Supply Corp. Fax number: 1-610-667-3415 6800 Gisholt Drive Madison, WI 53708 1C6Z1 Cohn and Gregory Inc. Phone number: 1-608-222-7799 1805 East Avenue Fax number: 1-608-223-6621 Fort Worth,

47、TX 76111 Phone number: 1-972-641-0835 1F524 Worly Plumbing Supply Inc. 400 Greenlawn Avenue Columbus, OH 43223 Phone number: 1-614-445-1000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59617 8 7.6 Part number (P/N) supersession data. These CID

48、 part numbers supersede the following MFRs P/Ns as shown. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE IV. - P/N Data. CID PIN Superseded NSN MFRs CAGE MFRs P/N 1/ (See Section 2) part number 050R4 AA59617-03 WWU516-03 4730-00-287-0

49、421 65430 84849 8A440 AA59617-11 WWU516-11 4730-00-189-2588 1F524 AA59617-17 WWU516-17 4730-00-248-9348 84849 84849 03958 8A440 AA59617-19 WWU516-19 4730-00-287-0422 5A784 3Z031 61-657-1/2 716517 AA59617-25 WWU516-25 4730-01-073-8113 05869 716516-4 84849 050R4 91050 1BS72 AA59617-27 WWU516-27 4730-00-289-5091 8A440 66200 04BQ9 84849 9M105 0APY9 0RVB7 03958 AA59617-29 WWU516-29 4730-00-266-3899 5A784 03670 19835 9M105 8484