DLA A-A-55313-1997 CAP UTILITY CAMOUFLAGE《鸭舌帽》.pdf

《DLA A-A-55313-1997 CAP UTILITY CAMOUFLAGE《鸭舌帽》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55313-1997 CAP UTILITY CAMOUFLAGE《鸭舌帽》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55313 993997.1 Ti175708 25T 4 distribution is unlimited. ? + Licensed by Information Handling ServicesA-A-55313 ?9999?Y 0375909 196 A-A-553 13 3. SKIENT cHARAcTElusTIcs 3.1 Description. The cap shall be a visor style (see Figures 1 through 4), having a lined, two- piece crown shaped with eight e

2、venly shaped, folded, and stitched darts; Marine Corps insignia (Type I cap); two metal eyelets at each side of the crown for ventilation; a lined outside band and a sweatband made from one ply of basic material; and a flexible, quilted hinge-type visor. The upper edge of the crown shall be folded a

3、nd stitched 1/16 inch fiom folded edge at upper dart ends for extra circumference of crown. The crown darts shall finish without gathers, puckers, and pleats. The height of the center fiont panel shall fnish evenly with the height of the top finished points of the fiont darts. The interiining shall

4、be singie stitched to the inside ply of the crown. The Marine Corps insignia deca (Type I cap) shall be placed in the center fiont of the crown. The eyelets shd be securely atache through each side of the crown. The outside band shall have an interiining with top edges even and stitched across fiil1

5、 width of stitching perpendicular to each other forming and X at the center together 118 inch fiom the edge of the entire length of the band. The ends of the band shall be joined with a 114 inch seam and backstitched to form a sweatband. The visor shall be smooth and free of wrinkles, gathers, pucke

6、rs, and other distortions. The visor quiiting shall be uniform with 4 rows of stitching spaced 3/8 to 114 inch apart and parallel to the outer edge of visor. 3.2 Material. 3.2.1 Basic material. The cap material, including the sweatband, shall be a nylodcotton blend, wind resistant poplin, woodland c

7、amouflage printed cloth. The warp and filling yarns shall be 50 - + 5 percent nylon, 1 percent static dissipative fiber, and the remaining percentage cotton. The warp yarn shall be 2-ply or singles. The weave shall be a plain weave with reinforcement ribs in both directions forming a uniform pattern

8、. The ribs shali be formed by having every twenty- fourth warp end contain two ends weaving as one and every thirteenth filling pick contain two picks weaving as one. The inside crown and sweatband shall be the basic material or it may be dyed the ground shade of the basic material, or it may be pri

9、nted seconds of the basic material. The color shall be a Woodland Camouflage Pattern (Light Green 354, Dark Green 355, Brown 356, and Black 357). Au colors of the fnished cloth shall match the standard sample when viewed under itered tungsten lamps that approximate artificial daylight and that have

10、a correlated color temperature! of 7500 082 inch and stfiess of 35% to 60 dried after each cycle), light, perspiration, and weathering when tested according to AATCC 61-3A; AATCC 16-ption A; AATCC 15; and AATCC 1 1 1 A, respectively. The color of the dyed thread shall match the standard sample when

11、viewe under filtered tungsten lamps which approximate artificial daylight having a correlateci color temperature of 7500 200K with illumination of 100 2 20 foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2300 5 200K. I/ 6 Licensed by Information Handlin

12、g Servicesi A-A-553 13 As an alternate, the thread shall be cotton-covered, polyester core thread, 36-45 Tex, 2 ply, with a breaking strength of 3.2 pounds minimum and 26 percent maximum elongation when tested according to ASTM-D-2256. (Speed shall be 12 lr 0.5 inch/minute and a 10 inch gauge length

13、 shall be used). The direction of twist for the single ply shall be “S“ and for the plied thread “2“. The thread shall be dyed Olive Drab shade S-1, C.A. 66022. The dyed and finished thread shd show fastness to laundering (3 cycles; dried after each cycle), dry heat, light (exposure time shall be 40

14、 standard fading hours), perspiration, and weathering (exposure time shall be 80 hours) equal to or better than the standard sample when tested according to AATCC 61-34 AATCC 1 17; AATCC 16, Option A, AATCC 15; and AATCC 1 1 14 respectively. The dyed thread shali be compared to the standard sample u

15、nder artificial daylight at 7000 2 500K and iridescent lamplight at 2850 5 1OOK. The thread shall contain only the minimum amount of lubricant to facilitate sewing. The yarn finish shall be non-staining and non-flame propagating. l/ - l! Certificates of compliance shall be submitted for all requirem

16、ents and the Government reserves the right to inspect such items to determine the validity of the certification. 3.2.6 Labels. Each cap shall have an identification label, a size label, and a care label. The size and identification labels or the identification and care labels may be combined. The id

17、entification label shall contain the item description, contract number, fiber content information, and the contractors name. The label color shall be Medium Green, Cable No. 70034,70130, or 7013 1 and shall show colorfastness to laundering in accordance with AATCC 61-3A. The inscription shall have a

18、 minimum font size of 10 points. The inscription legibility, label, and label attachment shall last the expected life of the cap. The care or the combination label, as applicable, shall include the following information. 1. 2. 3. 4. 5. If worn under helmet, helmet band may require readjustment for p

19、roper fit and comfort. Machine washing. Use Permanent Press Cycle. Wash in warm water with mild detergent. Hand washing. Wash in warm water using mild detergent. DO NOT WRING OR TWIST. Rinse in clean warm water. DO NOT USE CHLORINE BLEACH OR STARCH. Dry at low heat (Do not exceed 1300F). After dryin

20、g, tumble at room temperature for approximately 10 minutes. Remove immediately fiom dryer. DO NOT REMOVE THIS LABEL The size label shall show the sine designation and the stock number as shown by the following example: Small Stock Number 7 Licensed by Information Handling ServicesA-A-553 13 3.2.6. I

21、 LabeVtaq. Each item sha be individually bar-coded with a paper tag for personal clothing items. The paper tag shall be standard bleached sulfate having a basis weight of 100 pounds. The paper used for the tags shall have a smooth finish to accept thermal transfer and direct printing. The tags shall

22、 have a hole and shall be attached to each item by a fastener, clearly legible and readable by a scanner. The bar coding element shall be a 13 digit national stock number (NSN). The bar code type shall be a medium to high code density and shall be located so that it is completely visible on the item

23、 when it is folded and/or packaged as specified and so that it causes no damage to the item. 3.3 Sizes and measurements. The finished caps shall conform to the measurements specified in Table V. TABLE V. Cap sizes (inches) Size Inside hat circumference 1/4 inch tolerance) Extra-Extra Small 20-1/2 Ex

24、tra Small 21-114 Small 22 Medium 22-3/4 23-1/2 24-1/4 . Large Extrame 3.4 Patterns. A set of standard patterns to be used to cut working patterns will be frnished by the Government. The working patterns shall be identical to the Government patterns. Neither the Govemment patterns nor the working pat

25、terns shall be altered in any way, except that additional notches for use during construction are allowed on the working patterns. Also, minor mdications are permitted where neceswy when using automatic equipment. These modifications shall not alter the dmensional, serviceability, or appearance requ

26、irements. The standard patterns provide a seam allowance of 3/8 inch for the joining seams, and 114 inch for all other seams. 4. REGULATORY REOUREMENTS . The o color not as specified; any part shaded; any spot or stain (outside); raw edges, open seams, thread ends not removed, or loose tension resul

27、ting in loose seams; any material defects, distorted parts or poor workmanship; added, missing, or defective eyelets; visor not centered, secured properly, or constructed as specified; any band twisted, pleated, excessively full or irregular; any crown improperly stitched; any darts omitted; any ins

28、ignia not type, size, or color specified; any twisted or tight sweatband; any component part omitted; label missing, incorrect, or illegible; measurement of item not as specified; bar code omitted or not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code not visi

29、ble on folded, packaged item; bar code causes damage to the item; any items not packaged in accordance with the contract or purchase order. 5.4 Acceptance criteria. Acceptance criteria shall be as specified in the contract or purchase order. 6. PACKAGING 6.1 Preservation. packinn. and marking. The p

30、reservation, packing, and marking shall be as specified in the contract or purchase order. 7. NOTES 7.1 Source of Government documents. Copies of military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19 1 1 1-5094 7.2 Sou

31、rce of non-Government documents ASTM Test Methods (Applications for copies should be addressed to American Society For Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) AATCC Test Methods (Applications for copies should be addressed to American Association of Te

32、xtile Chemists and Colorists (AATCC), P.O. Box 12215, Triangle Park, NC 27709-2215.) TAPPI Test Methods (Applications for copies should be addressed to Technical Association of the Pulp and Paper Industry (TAPPI), Technology ParWAtlanta, P. O. Box 1051 13, Atlanta, GA 30348.) 9 Licensed by Informati

33、on Handling ServicesA-A-553 13 MILITARY INTERESTS: Custodian: Navy - MC Review Activities Navy - NU, YD CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS , PREPARING ACTIVITY: DLA - CT Project 8405-0328 10 Licensed by Information Handling Services. A-A-553 13 JYPE I y - .-_- ,- TYPE Il FIGURE 1. Cap, Ut

34、ility, Camoufage 11 Licensed by Information Handling ServicesA-A-55333 7Ls 0375939 035 - A-A-55313 MARINE CORPS INSIGNIA 114“+1 il 6 4- 2-318“ . FIGURE 2. Cap, Utility, Camoufage l2 Licensed by Information Handling Services A-A-55313 E qq?4 ?L?5920 857 - A-A-55313 FIGURE 3. Cap, Utility, Camouflage 13 Licensed by Information Handling Services A-A-55313 E 99997 0$70921 793 . A-A-55313 f i FIGURE 4. Cap, Utility, Cimionnage 14 Y Y Licensed by Information Handling Services