DIN ISO 8820-6-2011 Road vehicles - Fuse-links - Part 6 Single-bolt fuse-links (ISO 8820-6 2007)《道路车辆 熔断器 第6部分 单螺栓连接熔断器(ISO 8820-6-2007)》.pdf

《DIN ISO 8820-6-2011 Road vehicles - Fuse-links - Part 6 Single-bolt fuse-links (ISO 8820-6 2007)《道路车辆 熔断器 第6部分 单螺栓连接熔断器(ISO 8820-6-2007)》.pdf》由会员分享，可在线阅读，更多相关《DIN ISO 8820-6-2011 Road vehicles - Fuse-links - Part 6 Single-bolt fuse-links (ISO 8820-6 2007)《道路车辆 熔断器 第6部分 单螺栓连接熔断器(ISO 8820-6-2007)》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、May 2011 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 43.

2、040.10!$o$U“1760150www.din.deDDIN ISO 8820-6Road vehicles Fuse-links Part 6: Single-bolt fuse-links (ISO 8820-6:2007)English translation of DIN ISO 8820-6:2011-05Straenfahrzeuge Sicherungseinstze Teil 6: Kompaktsicherungseinstze (ISO 8820-6:2007)Englische bersetzung von DIN ISO 8820-6:2011-05Vhicule

3、s routiers Liaisons fusibles Partie 6: Liaisons fusibles poste singulier (ISO 8820-6:2007)Traduction anglaise de DIN ISO 8820-6:2011-05www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1304.11 A comma is used as the decimal marker. C

4、ontents 2 DIN ISO 8820-6:2011-05 Page National foreword .3 National Annex NA (informative) Bibliography.3 1 Scope 4 2 Normative references 4 3 Terms and definitions4 4 Marking and labelling 5 5 Tests and requirements 5 5.1 General5 5.1.1 General test conditions.5 5.1.2 Test sequence6 5.1.3 Test cabl

5、e sizes6 5.2 Voltage drop .7 5.2.1 Tests7 5.2.2 Requirements .7 5.3 Transient current cycling7 5.3.1 Test7 5.3.2 Requirement .8 5.4 Environmental conditions.8 5.5 Operating time rating.8 5.5.1 Test8 5.5.2 Requirement .8 5.6 Current steps9 5.6.1 Test9 5.6.2 Requirement .9 5.7 Breaking capacity 9 5.7.

6、1 Test9 5.7.2 Requirement .9 5.8 Strength of terminals.9 5.9 Strength of insulating body of the fuse-link and insulating nut .9 5.9.1 Purpose.9 5.9.2 Test9 5.9.3 Requirement .10 6 Dimensions.10 6.1 Single-bolt fuse-link.10 6.2 Mounting example .11 7 Test fixture11 National foreword This standard has

7、 been prepared by Technical Committee ISO/TC 22 “Road vehicles”, (Secretariat: AFNOR, France), Subcommittee SC 3 “Electrical and electronic equipment” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Automobiltechnik (Road Vehicle Engineeri

8、ng Standards Committee), Working Group NA 052-01-03-05 AK Sicherungen. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. DIN ISO 8820 consists of the f

9、ollowing parts, under the general title Road vehicles Fuse-links: Part 1: Definitions and general test requirements Part 2: Users guide Part 3: Fuse-links with tabs (blade type) Part 4: Fuse-links with female contacts (type A) and bolt-in contacts (type B) and their test fixtures Part 5: Fuse-links

10、with axial terminals (Strip fuse-links) Types SF 30 and SF 51 and test fixtures Part 6: Single-bolt fuse-links Part 7: Fuse-links with tabs (Type G) with rated voltage of 450 V The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 4017 DIN EN IS

11、O 4017 National Annex NA (informative) Bibliography DIN EN ISO 4017, Hexagon head screws Product grades A and B 3 DIN ISO 8820-6:2011-05 1 Scope This part of ISO 8820 specifies single-bolt fuse-links in road vehicles. It establishes, for this fuse-link type, the rated current, test procedures, perfo

12、rmance requirements and dimensions. This part of ISO 8820 is applicable to fuse-links with a rated voltage of 58 V, a current rating of u 300 A and a breaking capacity of 2 000 A intended for use in road vehicles at a nominal voltage of 12 V, 24 V and/or 42 V. This part of ISO 8820 is intended to be

13、 used in conjunction with ISO 8820-1 and with ISO 8820-2. The numbering of its clauses corresponds to that of ISO 8820-1, whose requirements are applicable, except where modified by requirements particular to this part of ISO 8820. 2 Normative references The following referenced documents are indisp

14、ensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4017, Hexagon head screws Product grades A and B ISO 8820-1, Road vehicles Fuse-links Part

15、 1: Definitions and general test requirements ISO 8820-2, Road vehicles Fuse-links Part 2: Users guide ISO 6722, Road vehicles 60 V and 600 V single-core cables Dimensions, test methods and requirements 3 Terms and definitions For the purposes of this Part of ISO 8820, the terms and definitions give

16、n in ISO 8820-1 and the following apply. 3.1 insulating nut electrically insulated device used to assemble a single-bolt fuse Road vehicles Fuse-links Part 6: Single-bolt fuse-links 4 DIN ISO 8820-6:2011-05 4 Marking and labelling The requirements given in ISO 8820-1 and Table 1 of this part of ISO

17、8820 apply. Table 1 Fuse-link colour coding Fuse-link rating A Colour 50 red 75 brown 100 yellow 125 green 150 orange 175 white 200 blue 250 pink 300 grey 5 Tests and requirements 5.1 General 5.1.1 General test conditions In addition to carrying out the test procedures in accordance with ISO 8820-1,

18、 the following criteria shall apply: Tests shall be performed following the test sequences in Table 2. The test fixtures for electrical tests shall be designed in accordance with Figure 4. The connection resistance shall be 0,35 m max. to ensure the proper function of the test fixture. Terminals sha

19、ll have a suitable finish which will assure corrosion protection, and shall have satisfactory mechanical and electrical properties. The mounting torque shall be (12 1) Nm. The insulation resistance of the insulating nut measured with 100 V d.c. shall be 10 M. 5 DIN ISO 8820-6:2011-05 5.1.2 Test sequ

20、ence Table 2 Test sequences Sample groups aNo. Requirement/Test Clause 1 2 3 4 5 6 7 1 Dimensions 6 X X X 2 Marking and labelling 4 X X X X X X X 3 Strength of insulating body 5.9 X X X X X X X 4 Voltage drop 5.2 X X X 5 Accelerated ageing 5.4 X 6 Fluid compatibility 5.4 X 7 Mechanical load 5.4 X 8

21、Transient current cycling 5.3 X 9 Voltage drop 5.2 X X X X 10 Current steps 5.6 X 11 Breaking capacity 5.7 X 1,00 IRX X X X X 1,35 IRYbY Y Y Y 1,50 IRY Y Y Y Y 2,00 IRY Y Y Y Y 3,50 IRY Y Y Y Y 12 Operating time rating 6,00 IR5.5 Y Y Y Y Y 13 Strength of insulating body 5.9 X X X X X X X aEach sampl

22、e group shall contain a minimum of 10 fuse links. bFor these operating time tests noted with a Y, the sample groups 2, 4, 5, 6 and 7 for each current rating shall be divided equally. These fuses are intended to be subjected to a single operating time test only. 5.1.3 Test cable sizes Test cable size

23、s shall be as given in Table 3. All tests for a particular fuse-link rating shall be performed using the same cable size. Test cable sizes are specified to allow comparative fuse-link tests to be carried out. The cable size specified does not necessarily indicate the size of cable to be used in the

24、vehicle application. 6 DIN ISO 8820-6:2011-05 Table 3 Test cable sizes Fuse-link rating A Conductor cross-sectional areaamm250 75 10 100 125 16 150 175 25 200 35 250 50 300 70 a Conductor material according to ISO 6722.5.2 Voltage drop 5.2.1 Tests The test given in ISO 8820-1 and Figure 3 of this pa

25、rt of ISO 8820 shall apply. 5.2.2 Requirements The requirements given in Table 4 shall apply. Table 4 Voltage drop Fuse-link rating A Max. fuse-link voltage drop mV 50 110 75 105 100 100 125 95 150 90 175 85 200 80 250 75 300 70 5.3 Transient current cycling 5.3.1 Test Figure 1 and the test given in

26、 ISO 8820-1 shall apply. This test shall be performed at an environmental temperature of (90 5) C. At an elapsed time of 0,25 s on-time, the current shall fall to a value between 1,25 IRand 1,35 IR. At no time shall the steady state current fall below 0,50 IR. 7 DIN ISO 8820-6:2011-05 Key I current

27、in A t time in s aone cycle b4 IRFigure 1 Transient current cycling 5.3.2 Requirement The requirements given in ISO 8820-1 shall apply. 5.4 Environmental conditions The tests and requirements given in ISO 8820-1 shall apply. 5.5 Operating time rating 5.5.1 Test The test given in ISO 8820-1 shall app

28、ly. 5.5.2 Requirement The requirements given in Table 5 shall apply. After activation, the current through the fuse-link shall not exceed 0,5 mA at the rated voltage of the fuse-link. 8 DIN ISO 8820-6:2011-05 Table 5 Operating times Operating time s Test current A min. max.1,0 IR360 000 1,35 IR5 1 8

29、00 1,5 IR1 600 2,0 IR0,2 60 3,5 IR0,03 1,0 6,0 IR0,01 0,2 5.6 Current steps 5.6.1 Test The test given in ISO 8820-1 shall apply. 5.6.2 Requirement The requirement given in ISO 8820-1 shall apply. After activation, the current through the fuse-link shall not exceed 0,5 mA at the rated voltage of the

30、fuse-link. 5.7 Breaking capacity 5.7.1 Test The test given in ISO 8820-1 shall apply. Test at 2 000 A with cable sizes as shown in Table 3. 5.7.2 Requirement The requirement given in ISO 8820-1 shall apply After activation, the current through the rated voltage of the fuse-link shall not exceed 0,5

31、mA at UR= 58 V. 5.8 Strength of terminals Not applicable. 5.9 Strength of insulating body of the fuse-link and insulating nut 5.9.1 Purpose The purpose for this test given in ISO 8820-1 shall apply. 5.9.2 Test Install the fuse-links in the test fixture with the mounting torque of (12 1) Nm. NOTE Tes

32、t number 13 in Table 2 “test sequence” is just a removal from the test fixture. 9 DIN ISO 8820-6:2011-05 5.9.3 Requirement Fuse-links and insulating nuts shall remain physically intact. 6 Dimensions 6.1 Single-bolt fuse-link Dimensions in millimetres Figure 2 Single-bolt fuse-link 10 DIN ISO 8820-6:

33、2011-05 6.2 Mounting example Dimensions in millimetres Key 1, 2 measuring points for voltage drop 3 insulating nut 4 bolt Figure 3 Mounting example 7 Test fixture Table 6 Parts list and material specifications Reference No. in Figure 4 Description Dimensions see figure Material specifications, finis

34、h and coating Quantity 1 Test fixture insulating body 2 Thermoset plastic 1 2 Bolt: ISO 4017-M850-8.8 Steel, gal. Zn 1 3 Washer: DIN 125-A8,4 Steel, gal. Zn 1 4 Nut: ISO 40323-M8-8 Steel, gal. Zn 2 11 DIN ISO 8820-6:2011-05 Dimensions in millimetres Tolerances: ISO 2768 Key 1, 2, 3, 4 see Table 6 Figure 4 Test fixture 12 DIN ISO 8820-6:2011-05 Dimensions in millimetres Tolerances: ISO 2768 Key SW width across flats aOptionally dove-tailing. All corners and edges shall be rounded R1. Figure 5 Test fixture insulating body 13 DIN ISO 8820-6:2011-05