DIN EN ISO 8676-2011 Hexagon head screws with metric fine pitch thread - Product grades A and B (ISO 8676 2011) German version EN ISO 8676 2011《公制细牙螺纹六角头螺钉 产品等级A和B(ISO 8676-2011) 德.pdf
《DIN EN ISO 8676-2011 Hexagon head screws with metric fine pitch thread - Product grades A and B (ISO 8676 2011) German version EN ISO 8676 2011《公制细牙螺纹六角头螺钉 产品等级A和B(ISO 8676-2011) 德.pdf》由会员分享,可在线阅读,更多相关《DIN EN ISO 8676-2011 Hexagon head screws with metric fine pitch thread - Product grades A and B (ISO 8676 2011) German version EN ISO 8676 2011《公制细牙螺纹六角头螺钉 产品等级A和B(ISO 8676-2011) 德.pdf(19页珍藏版)》请在麦多课文档分享上搜索。
1、July 2011 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2
2、1.060.10!$sP“1804559www.din.deDDIN EN ISO 8676Hexagon head screws with metric fine pitch thread Product grades A and B (ISO 8676:2011)English translation of DIN EN ISO 8676:2011-07Sechskantschrauben mit Gewinde bis Kopf und metrischem Feingewinde Produktklassen A und B (ISO 8676:2011)Englische berse
3、tzung von DIN EN ISO 8676:2011-07Vis tte hexagonale filetage mtrique pas fin entirement filetes Grades A et B (ISO 8676:2011)Traduction anglaise de DIN EN ISO 8676:2011-07SupersedesDIN EN ISO 8676:2001-03www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be cons
4、idered authoritative.1906.11 DIN EN ISO 8676:2011-07 National foreword This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (both secretariats are held by DIN, Germany). The responsible German body involved in it
5、s preparation was the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee), Working Committee NA 067-00-02 AA Verbindungs-elemente mit metrischem Auengewinde. The DIN 4000-160-1 tabular layout of article characteristics shall apply to screws covered in this standard. The D
6、IN Standards corresponding to the International Standards referred to in Clause 2 of this document are as follows: ISO 225 DIN EN ISO 225 ISO 724 DIN ISO 724 ISO 898-1 DIN EN ISO 898-1 ISO 965-1 DIN ISO 965-1 ISO 3269 DIN EN ISO 3269 ISO 3506-1 DIN EN ISO 3506-1 ISO 4042 DIN EN ISO 4042 ISO 4753 DIN
7、 EN ISO 4753 ISO 4759-1 DIN EN ISO 4759-1 ISO 6157-1 DIN EN 26157-1 ISO 8839 DIN EN 28839 ISO 8992 DIN ISO 8992 ISO 10683 DIN EN ISO 10683 Amendments This standard differs from DIN EN ISO 8676:2001-03 as follows: a) normative references are now undated; b) the standard has been editorially revised a
8、nd normative references have been updated; c) Annex ZA has been deleted. Previous editions DIN 961: 1952-12, 1963-03, 1967-11, 1970-11, 1983-12, 1990-01 DIN ISO 8676: 1990-01 DIN EN 28676: 1992-02 DIN EN ISO 8676: 2001-03 2 A comma is used as the decimal marker. DIN EN ISO 8676:2011-07 National Anne
9、x NA (informative) Bibliography DIN 4000-160, Tabular layout of product properties Part 160: Fasteners with external thread DIN EN 26157-1, Fasteners Surface discontinuities Bolts, screws and studs subject to general requirements DIN EN 28839, Mechanical properties of fasteners Nonferrous metal bolt
10、s, screws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pi
11、tch thread DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4753, Fasteners Ends of parts with external ISO metric th
12、read DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN ISO 724, ISO general purpose metric screw threads Basic dimensions DIN ISO 965-1, ISO general purpose metr
13、ic screw threads Tolerances Part 1: Principles and basic data DIN ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts 3 DIN EN ISO 8676:2011-07 This page is intentionally blank 4 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8676 April 2011 ICS 21.060.10 Supersedes
14、EN ISO 8676:2000English Version Hexagon head screws with metric fine pitch thread Product grades A and B (ISO 8676:2011) Vis tte hexagonale filetage mtrique pas fin entirement filetes Grades A et B (ISO 8676:2011) Sechskantschrauben mit Gewinde bis Kopf und metrischem Feingewinde Produktklassen A un
15、d B (ISO 8676:2011) This European Standard was approved by CEN on 31 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and
16、bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the re
17、sponsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,
18、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Mana
19、gement Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 8676:2011: EContents Page Foreword .3 Introduction.4 1 Scope.5 2 Normative references 5 3 Dimensions .6 4 Specifications and
20、reference International Standards.13 5 Designation.13 Bibliography14 EN ISO 8676:2011 (E) DIN EN ISO 8676:2011-07 2Foreword This document (EN ISO 8676:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat
21、of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at the latest by October 2011. Attention is drawn to th
22、e possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 8676:2000. According to the CEN/CENELEC Internal Regulations, the national sta
23、ndards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DINENISO86762011HEXAGONHEADSCREWSWITHMETRICFINEPITCHTHREADPRODUCTGRADESAANDBISO86762011GERMANVERSIONENISO86762011

链接地址:http://www.mydoc123.com/p-681977.html