DIN EN 16287-2-2014 Glass packaging - Screw finishes for pressure capsules - Part 2 One way glass MCA 1 finish German version EN 16287-2 2014《玻璃包装 压力传感器用螺旋抛光 第2部分 单向玻璃MCA 1抛光 德文版本E.pdf

《DIN EN 16287-2-2014 Glass packaging - Screw finishes for pressure capsules - Part 2 One way glass MCA 1 finish German version EN 16287-2 2014《玻璃包装 压力传感器用螺旋抛光 第2部分 单向玻璃MCA 1抛光 德文版本E.pdf》由会员分享，可在线阅读，更多相关《DIN EN 16287-2-2014 Glass packaging - Screw finishes for pressure capsules - Part 2 One way glass MCA 1 finish German version EN 16287-2 2014《玻璃包装 压力传感器用螺旋抛光 第2部分 单向玻璃MCA 1抛光 德文版本E.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、July 2014 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 55

2、.100!%5zY“2188754www.din.deDDIN EN 16287-2Glass packaging Screw finishes for pressure capsules Part 2: One way glass MCA 1 finish;English version EN 16287-2:2014,English translation of DIN EN 16287-2:2014-07Verpackungen aus Glas Schraubmundstcke fr Flaschen mit Innendruck Teil 2: Einweg-MCA 1-(Glas-

3、)Mundstck;Englische Fassung EN 16287-2:2014,Englische bersetzung von DIN EN 16287-2:2014-07Emballage en verre Bagues vis pour capsules pression Partie 2: Bague MCA 1 pour verre perdu;Version anglaise EN 16287-2:2014,Traduction anglaise de DIN EN 16287-2:2014-07Together withDIN EN 16287-1:2014-07,sup

4、ersedesDIN 6094-14:1995-02www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 12 pages06.14 DIN EN 16287-2:2014-072 A comma is used as the decimal marker. National foreword This document (EN 16287-2:2014) has been prepared by Technical Comm

5、ittee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Verpackungswesen (Packaging Standards Committee), Working Committee NA 115-02-04 AA Behltnisse aus Glas. In addition to the legal units of measurement, this stan

6、dard also uses the unit “in” (inch). It should be noted that the Gesetz ber Einheiten im Messwesen (German Law on units in metrology) prohibits the use of this unit for official and commercial purposes in Germany. Conversion: Non-SI unit SI unit Conversion in (inch) mm 1 in = 25,4 mm Amendments This

7、 standard differs from DIN 6094-14:1995-02 as follows: a) the content of DIN 6094-14 has been incorporated into DIN EN 16287-1 and DIN EN 16287-2; b) the standard has been editorially revised. Previous editions DIN 6094-14: 1984-03, 1985-06, 1995-02 EN 16287-2March 2014 ICS 55.100 English Version Gl

8、ass packaging - Screw finishes for pressure capsules - Part 2: One way glass MCA 1 finish Emballage en verre - Bagues vis pour capsules pression - Partie 2: Bague MCA 1 pour verre perdu Verpackungen aus Glas - Schraubmundstcke fr Flaschen mit Innendruck - Teil 2: Einweg-MCA 1-(Glas-)Mundstck This Eu

9、ropean Standard was approved by CEN on 12 January 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

10、 concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN memb

11、er into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Fra

12、nce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All right

13、s of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16287-2:2014 EEUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 16287-2:2014 (E) 2 Contents PageFo

14、reword 3 Introduction .4 1 Scope 5 2 Terms and definitions .5 3 Dimensions .5 Bibliography . 10 DIN EN 16287-2:2014-07EN 16287-2:2014 (E) 3 Foreword This document (EN 16287-2:2014) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This Europe

15、an Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2014 and conflicting national standards shall be withdrawn at the latest by September 2014. Attention is drawn to the possibility that some of the el

16、ements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 16287, Glass packaging Screw finishes for pressure capsules, consists of the following parts: Part 1: Returnable glass MCA 1 finish Part 2:

17、One way glass MCA 1 finish According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republi

18、c of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 16287-2:2014-07EN 16287-2:2014 (E) 4 Introduction Thi

19、s European Standard is based on CE.T.I.E. (International Technical Centre for Bottling and related Packaging) data sheet GME 32.05.1 Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of t

20、he contents of the pack. DIN EN 16287-2:2014-07EN 16287-2:2014 (E) 5 1 Scope This European Standard specifies the dimensions of the 28 mm screw finish for glass containers designated MCA 1 for one way glass. 2 Terms and definitions For the purposes of this document, the following term and definition

21、 applies. 2.1 MCA (glass) finish designed for the closure of pressurized or vacuum liquids with a tamper-evident closure (metal or plastic) 3 Dimensions The design and dimensions of the finish shall be as shown in Table 1 and Figure 1, Figure 2, Figure 3, Figure 4 and Figure 5. Table 1 Design and di

22、mensions of the finish Pitch TPI cutter 3,175 mm 2 12 8 12,5 mm = Helix angle or angle or fixture to cutter. NOTE TPI = Threads per Inch. One inch is equal to 25,4 mm. The Tan of helix angle for cutter is calculated via the following formula: ( )2nominalnominalpitchTanET += where T is the thread dia

23、meter; E is the wall diameter of threaded finish. The average of the maximum and minimum of L diameter is as close as possible to L nominal. The mean diameter 2mindiametermaxdiameter +L is in the tolerance of 0,2 mm. Optional: Depressed thread at mould parting line (see EN 16292). DIN EN 16287-2:201

24、4-07EN 16287-2:2014 (E) 6 Dimensions in millimetres Key N neck (under bead) diameter H thread height S start of thread position from sealing surface to intersection of thread flank F height of the finish L locking bead diameter T thread diameter E wall diameter of threaded finish NOTE Bore diameter

25、19 mm max. for a depth of 3 mm Figure 1 MCA 1 finish DIN EN 16287-2:2014-07EN 16287-2:2014 (E) 7 Dimensions in millimetres Type 1 Type 2 Key a Mould parting line b Sealing surface Figure 2 Possible alternative constructions of the bore entrance to suit glass manufacturer The sealing surface is smoot

26、h and free of any defects and flash. DIN EN 16287-2:2014-07EN 16287-2:2014 (E) 8 Dimensions in millimetres Minimum through bore 16,0 Figure 3 Detail of the profile NOTE Z-Z is the last full depth and width of thread. Beyond this point and Y-Y, the thread root is gradually increased to full thread di

27、ameter T in 90. Figure 4 Run out of thread DIN EN 16287-2:2014-07EN 16287-2:2014 (E) 9 Dimensions in millimetres Figure 5 Limit of construction DIN EN 16287-2:2014-07EN 16287-2:2014 (E) 10 Bibliography 1 CE. T.I.E. data sheet GME 32.05 - MCA 1 finish 1)2 EN 16292, Glass packaging - Screw finishes - Depressed threads 1) Obtainable through Centre Technique International de lEmbouteillage et du conditionnement (CE.T.I.E), 112- 114, rue La Botie, 75008 Paris, France www.cetie.org, TP: 0033-1-42 65 26 45, TF: 0033-1-40 07 03 21. DIN EN 16287-2:2014-07