DIN EN 771-5-2015 Specification for masonry units - Part 5 Manufactured stone masonry units German version EN 771-5 2011+A1 2015《砌块产品规范 第5部分 人造石料砌块 德文版本EN 771-5-2011+A1-2015》.pdf

《DIN EN 771-5-2015 Specification for masonry units - Part 5 Manufactured stone masonry units German version EN 771-5 2011+A1 2015《砌块产品规范 第5部分 人造石料砌块 德文版本EN 771-5-2011+A1-2015》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 771-5-2015 Specification for masonry units - Part 5 Manufactured stone masonry units German version EN 771-5 2011+A1 2015《砌块产品规范 第5部分 人造石料砌块 德文版本EN 771-5-2011+A1-2015》.pdf（37页珍藏版）》请在麦多课文档分享上搜索。

1、November 2015 English price group 16No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.100.30!%GA“2365730www.din.de

2、DIN EN 771-5Specification for masonry units Part 5: Manufactured stone masonry units;English version EN 771-5:2011+A1:2015,English translation of DIN EN 771-5:2015-11Festlegungen fr Mauersteine Teil 5: Betonwerksteine;Englische Fassung EN 771-5:2011+A1:2015,Englische bersetzung von DIN EN 771-5:2015

3、-11Spcifications pour lments de maonnerie Partie 5: Elments de maonnerie en pierre reconstitue;Version anglaise EN 771-5:2011+A1:2015,Traduction anglaise de DIN EN 771-5:2015-11SupersedesDIN EN 771-5:2011-07See start of applicationwww.beuth.deDTranslation by DIN-Sprachendienst.In case of doubt, the

4、German-language original shall be considered authoritative.Document comprises 37 pages 10.15 DIN EN 771-5:2015-11 2 A comma is used as the decimal marker. Start of application It should be noted that, in Germany, CE conformity marking of construction products will be permitted once this standard has

5、 been listed in the Official Journal of the European Union and/or the Bundesanzeiger (German Federal Gazette) and from the date given therein. For further information, users of this standard should refer to the websites of the European Commission or of the relevant building authority. The standard w

6、hich this document replaces, DIN EN 771-5:2011-07, may be used in parallel with this standard during a specified transition period where such has been laid down in the Official Journal of the European Union and/or the Bundesanzeiger (German Federal Gazette). National foreword This document (EN 771-5

7、:2011+A1:2015) has been prepared by Technical Committee CEN/TC 125 “Masonry” (Secretariat: BSI, United Kingdom). The responsible German body involved in its preparation was DIN-Normenausschuss Bauwesen (DIN Standards Committee Building and Civil Engineering), Working Committee NA 005-06-02 AA Koordi

8、nie-rungsausschuss Mauersteine (SpA zu CEN/TC 125/WG 1). Amendments This standard differs from DIN EN 771-5:2011-07 as follows: a) the entire document has been editorially revised; b) Annex ZA has been completely revised. Previous editions DIN EN 771-5: 2004-05, 2005-05, 2011-07 EUROPEAN STANDARD NO

9、RME EUROPENNE EUROPISCHE NORM EN 771-5:2011+A1 August 2015 ICS 91.100.30 Supersedes EN 771-5:2011English Version Specification for masonry units - Part 5: Manufactured stone masonry units Spcifications pour lments de maonnerie - Partie 5: Elments de maonnerie en pierre reconstitue Festlegungen fr Ma

10、uersteine - Teil 5: Betonwerksteine This European Standard was approved by CEN on 17 March 2011 and includes Amendment 1 approved by CEN on 11 January 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the

11、status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French

12、, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, C

13、roatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey an

14、d United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. N

15、o. EN 771-5:2011+A1:2015 EEN 771-5:2011+A1:2015 (E) 2 Contents Page European foreword .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Materials .8 5 Requirements for manufactured stone masonry units 8 5.1 General 8 5.2 Dimensions and tolerances 8 5.2.1 Dimensions .8 5.2.2 Dimensio

16、nal tolerances 9 5.3 Configuration and appearance 10 5.3.1 General . 10 5.3.2 Configuration 10 5.3.3 Surface appearance 10 5.3.4 Flatness of surfaces . 10 5.4 Density . 11 5.5 Compressive strength 11 5.5.1 Declared value . 11 5.5.2 Minimum value 12 5.6 Thermal properties . 12 5.7 Durability . 12 5.8

17、 Water absorption by capillarity . 12 5.8.1 Declared value . 12 5.8.2 Maximum value . 13 5.9 Moisture movement 13 5.10 Water vapour permeability . 13 5.11 Reaction to fire 13 5.12 Shear bond strength . 13 5.12.1 General . 13 5.12.2 Declaration based on fixed values 13 5.12.3 Declaration based on tes

18、ts 13 5.13 Flexural bond strength . 14 5.14 Dangerous substances 14 6 Description, designation and classification of manufactured stone masonry units . 14 6.1 Description and designation . 14 6.2 Classification . 15 7 Marking 15 8 !Assessment and verification of constancy of performance (AVCP)“ 15 8

19、.1 General . 15 8.2 !Product type determination“ 15 8.3 Factory production control 17 8.3.1 General . 17 8.3.2 Testing and measuring equipment . 17 8.3.3 Production equipment 17 8.3.4 Raw materials 17 8.3.5 Production process 17 DIN EN 771-5:2015-11 EN 771-5:2011+A1:2015(E)3 8.3.6 Finished product t

20、esting . 17 8.3.7 Statistical techniques 18 8.3.8 Marking and stock control of products . 18 8.3.9 Traceability . 18 8.4 Nonconforming products . 18 Annex A (normative) !Sampling for determination of product type and for independent testing of consignments“ 19 A.1 General . 19 A.2 Sampling procedure

21、 19 A.2.1 General . 19 A.2.2 Random sampling . 19 A.2.3 Representative sampling 19 A.2.4 Dividing the sample . 20 A.2.5 Number of units required for testing . 20 Annex B (normative) Normalised compressive strength . 21 Annex C (informative) Guidance for test frequencies for designing a FPC system to

22、 demonstrate conformity of finished products with the requirements of the standard and the declaration of the manufacturer 22 Annex ZA (informative) !Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation“ 24 ZA.1 Scope and relevant characteristics . 2

23、4 ZA.2 Procedure(s) for AVCP of manufactured stone masonry units 25 ZA.2.1 System(s) of AVCP 25 ZA.2.2 Declaration of performance (DoP) . 27 ZA.3 CE marking and labelling 32 Bibliography 35 DIN EN 771-5:2015-11 EN 771-5:2011+A1:2015(E)4 European foreword This document (EN 771-5:2011+A1:2015) has bee

24、n prepared by Technical Committee CEN/TC 125 “Masonry”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2016, and conflicting national standards s

25、hall be withdrawn at the latest by May 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes !EN 771-5:2011“.

26、 This document includes Amendment 1 approved by CEN on 2015-01-11. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. !This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and

27、 supports basic requirements for construction works of the EU Construction Products Regulation (Regulation (EU) No 305/2011). For relationship with EU Regulation/Directive(s), see informative Annex ZA, which is an integral part of this document.“ This European Standard also takes into account the ge

28、neral rules for unreinforced and reinforced masonry in Eurocode 6. EN 771, Specification for masonry units consists of: Part 1: Clay masonry units Part 2: Calcium silicate masonry units Part 3: Aggregate concrete masonry units (Dense and light weight aggregates) Part 4: Autoclaved aerated concrete m

29、asonry units Part 5: Manufactured stone masonry units Part 6: Natural stone masonry units According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Cze

30、ch Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdo

31、m. DINEN 771-5:2015-11EN 771-5:2011+A1:2015 (E) 5 1 Scope This European Standard specifies the characteristics and performance requirements of manufactured stone masonry units for which the main intended uses are facing or exposed masonry in load bearing or non-load bearing building and civil engine

32、ering applications. The units are suitable for all forms of coursed or random masonry walling, including single leaf, cavity, partition, retaining and the external masonry to chimneys. They can provide fire protection, thermal insulation, sound insulation and sound absorption. This standard covers c

33、oncrete masonry units manufactured to resemble natural stone using casting or pressing techniques with or without textured surfaces produced, by casting, splitting, washing, blasting or tooling and with or without variable outline effects. It covers homogeneous masonry units and those consisting of

34、different facing and backing concrete mixes, but excludes those manufactured with an adhesive bonded decorative face. This standard does not cover masonry units intended to conform to EN 771-3. It defines the performance related to e.g. strength, density, dimensional accuracy, surface appearance and

35、 provides for the !assessment and verification of constancy of performance (AVCP)“ of the product to this European Standard. The marking requirements for products covered by this European Standard are also included. This European Standard does not apply to storey height panels, masonry units used fo

36、r chimney flues or units manufactured with an adhesive bonded decorative face. It does not include products intended to be used as a damp proof course nor does it specify standard sizes for manufactured stone masonry units or work dimensions and angles of specially shaped units. It does not cover un

37、its with an incorporated thermal insulation material bonded to the faces of the unit susceptible to be exposed to fire. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated

38、references, the latest edition of the referenced document (including any amendments) applies. EN 772-1, Methods of test for masonry units Part 1: Determination of compressive strength EN 772-11, Methods of test for masonry units Part 11: Determination of water absorption of aggregate concrete, autoc

39、laved aerated concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of water absorption of clay masonry units EN 772-13, Methods of test for masonry units Part 13: Determination of net and gross dry density of masonry units (except for natural ston

40、e) EN 772-14, Methods of test for masonry units Part 14: Determination of moisture movement of aggregate concrete and manufactured stone masonry units EN 772-16:2011, Methods of test for masonry units Part 16: Determination of dimensions EN 772-20, Methods of test for masonry units Part 20: Determin

41、ation of flatness of faces of aggregate concrete, manufactured stone and natural stone masonry units EN 1052-2, Methods of test for masonry Part 2: Determination of flexural strength EN 1052-3, Methods of test for masonry Part 3: Determination of initial shear strength EN 1745, Masonry and masonry p

42、roducts Methods for determining thermal properties DIN EN 771-5:2015-11 EN 771-5:2011+A1:2015 (E) 6 EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests EN ISO 12572, Hygrothermal performance of building material

43、s and products Determination of water vapour transmission properties (ISO 12572:2001) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 masonry unit preformed component intended for use in masonry construction 3.2 facing masonry unit masonry un

44、it intended for use with one or more faces visible in use which may or may not be exposed 3.3 exposed face face intended to be exposed to external climatic conditions 3.4 manufactured stone masonry unit facing masonry unit having at least one exposed face with a close structure formed from either on

45、e or two homogeneous mixtures of aggregate, cementitious binder and other materials moulded under pressure and/or vibration and with or without further processing, intended to resemble and be used as an alternative to natural stone 3.5 two-part masonry unit masonry unit manufactured with different f

46、acing and backing concretes 3.6 co-ordinating size size of the co-ordinating space allocated to a masonry unit including an allowance for joints 3.7 work size size of a masonry unit specified for its manufacture to which the actual size conforms within permissible deviations 3.8 actual size size of

47、a masonry unit as measured 3.9 regular shaped masonry unit masonry unit with an overall rectangular parallelepiped shape 3.10 specially shaped masonry unit masonry unit which is not a rectangular parallelepiped DIN EN 771-5:2015-11 EN 771-5:2011+A1:2015 (E) 7 3.11 accessory unit masonry unit which i

48、s shaped to provide a particular function, e.g. to complete the geometry of the masonry 3.12 interlocking features shaped, matched projections and indentations on masonry units EXAMPLE Tongue and groove systems. 3.13 recess depression or indentation in one or more surfaces of a masonry unit EXAMPLE

49、Mortar pocket, rendering keyway. 3.14 normalised compressive strength of masonry units compressive strength of masonry units converted to the air dry compressive strength of an equivalent 100 mm wide 100 mm high masonry unit NOTE See procedure given in Annex B of this standard. 3.15 declared value value that a manufacturer is confident of achieving bearing in mind the precision of the test and the variability of the manufacturing process 3.16 pro