DIN EN 572-6-2012 Glass in building - Basic soda lime silicate glass products - Part 6 Wired patterned glass German version EN 572-6 2012《建筑用玻璃 基本钠钙硅酸盐玻璃制品 第6部分 嵌丝压花玻璃 德文版本EN 572-6.pdf

《DIN EN 572-6-2012 Glass in building - Basic soda lime silicate glass products - Part 6 Wired patterned glass German version EN 572-6 2012《建筑用玻璃 基本钠钙硅酸盐玻璃制品 第6部分 嵌丝压花玻璃 德文版本EN 572-6.pdf》由会员分享，可在线阅读，更多相关《DIN EN 572-6-2012 Glass in building - Basic soda lime silicate glass products - Part 6 Wired patterned glass German version EN 572-6 2012《建筑用玻璃 基本钠钙硅酸盐玻璃制品 第6部分 嵌丝压花玻璃 德文版本EN 572-6.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、November 2012 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 81.040.20!$HA“1923730www.din.deDDIN EN 572-6Glass in building Basic soda lime silicate glass products Part 6: Wired patterned glass;English version EN 572-6:2012,English translation of DIN EN 572-6:2012-11Glas im Bauwesen Basiserzeugnisse aus Kalk-Natronsilicatglas Teil 6: Drahtornamentglas;Englis

3、che Fassung EN 572-6:2012,Englische bersetzung von DIN EN 572-6:2012-11Verre dans la construction Produits de base: verre de silicate sodo-calcique Partie 6: Verre imprim arm;Version anglaise EN 572-6:2012,Traduction anglaise de DIN EN 572-6:2012-11SupersedesDIN EN 572-6:2004-09www.beuth.deIn case o

4、f doubt, the German-language original shall be considered authoritative.Document comprises 12 pages 10.12 DIN EN 572-6:2012-11 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 129 “Glass in building” (Secretariat: NBN, Belgium).

5、 The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-09-29 AA Glas im Bauwesen. Amendments This standard differs from DIN EN 572-6:2004-09 as follows: a) the standard has been editoria

6、lly revised; b) in Subclause 4.2 “Length, width and squareness” a new method for the determination of squareness has been specified. Previous editions DIN 1249-4: 1981-08 DIN EN 572-6: 1995-01, 2004-09 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 572-6 July 2012 ICS 81.040.20 Supersedes EN 5

7、72-6:2004English Version Glass in building - Basic soda lime silicate glass products - Part 6: Wired patterned glass Verre dans la construction - Produits de base: verre de silicate sodo-calcique - Partie 6: Verre imprim arm Glas im Bauwesen - Basiserzeugnisse aus Kalk-Natronsilicatglas - Teil 6: Dr

8、ahtornamentglas This European Standard was approved by CEN on 11 May 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliog

9、raphical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsib

10、ility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republi

11、c of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALIS

12、ATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 572-6:2012: EEN 572-6:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references

13、 43 Terms and definitions .44 Dimensional requirements 54.1 Thickness .54.1.1 General 54.1.2 Tolerances 64.2 Length, width and squareness .64.3 Wire mesh .65 Quality requirements .65.1 General 65.2 Methods of observation and measurement 75.2.1 Spot and linear/extended faults .75.2.2 Pattern faults 7

14、5.2.3 Wire faults .75.3 Acceptance levels 85.3.1 Spot faults 85.3.2 Linear/extended faults .85.3.3 Pattern faults 95.3.4 Wire faults .96 Designation 9Bibliography . 10DIN EN 572-6:2012-11 EN 572-6:2012 (E) 3 Foreword This document (EN 572-6:2012) has been prepared by Technical Committee CEN/TC 129 “

15、Glass in building”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2013, and conflicting national standards shall be withdrawn at the latest by Ja

16、nuary 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 572-6:2004. This document has been prepared un

17、der a mandate given to CEN by the European Commission and the European Free Trade Association. This edition is a revision of EN 572-6:2004. The main change in this edition is a new method of determination of squareness. This European Standard “Glass in building Basic soda lime silicate glass product

18、s” consists of the following parts: Part 1: Definitions and general physical and mechanical properties; Part 2: Float glass; Part 3: Polished wired glass; Part 4: Drawn sheet glass; Part 5: Patterned glass; Part 6: Wired patterned glass; Part 7: Wired or unwired channel shaped glass; Part 8: Supplie

19、d and final cut sizes; Part 9: Evaluation of conformity/Product standard. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Den

20、mark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 572-6:

21、2012-11 EN 572-6:2012 (E) 4 1 Scope This European Standard specifies dimensional and minimum quality requirements (in respect of optical and visual faults) for wired patterned glass, as defined in EN 572-1:2012, for use in building. This European Standard applies only to wired patterned glass suppli

22、ed in rectangular panes and in stock sizes. EN 572-8 gives information on patterned wired glass in sizes other than those covered by this European Standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its

23、application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 572-1:2012, Glass in building Basic soda lime silicate glass products Part 1: Definitions and general physical and mechanica

24、l properties 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 572-1:2012 and the following apply. 3.1 length, H, and width, B defined with reference to the direction of draw of the glass ribbon as shown in Figure 1 Key 1 direction of draw Figure 1 Rela

25、tionship between length, width and direction of draw 3.2 stock sizes glass delivered in the following sizes: nominal length H: 1 380 mm to 4 500 mm; nominal width B: 1 500 mm to 2 520 mm DIN EN 572-6:2012-11 EN 572-6:2012 (E) 5 3.3 visual fault fault which alters the visual quality of the glass Note

26、 1 to entry: Visual faults include spot faults, linear/extended faults, pattern faults and wire faults. 3.4 spherical or quasi-spherical spot fault spot fault whose larger dimension is less than or equal to twice the smaller dimension 3.5 elongation spot fault fault whose larger dimension is more th

27、an twice the smaller dimension 3.6 linear/extended fault fault which can be on or in the glass, in the form of deposits, marks or scratches which occupy an extended length or area 3.7 pattern fault deviation of the pattern relative to a reference, e.g. line or straight edge 3.8 deviation of the patt

28、ern deviation, x, of the pattern 3.9 wire fault deviations of the wire, penetration of the glass surface by the wire or break in the wire in the body of the glass 3.10 deviation of the wire deviation, y, of the wire relative to a reference, e.g. line or straight edge 4 Dimensional requirements 4.1 T

29、hickness 4.1.1 General The actual thickness shall be the average of four measurements, taken to the nearest 0,01 mm, each one taken at the thickest and closest point to the centre of each side. Measurement shall be by means of an instrument of the plate gauge type with a diameter of (50 5) mm. NOTE

30、The mechanical resistance of wired patterned glass is a function of the pattern as well as the thickness. DIN EN 572-6:2012-11 EN 572-6:2012 (E) 6 4.1.2 Tolerances The actual thickness rounded to the nearest 0,1 mm shall not vary from the nominal thickness by more than the tolerances shown in Table

31、1. Table 1 Tolerances on nominal thickness Dimensions in millimetres Nominal thickness Tolerances 6 0,67 0,78 0,89 +1,5 / -1,0 4.2 Length, width and squareness The tolerances, t, on nominal dimensions length, H, and width, B, are 5 mm. The limits of squareness are described by deviation between diag

32、onals. Such limits are given in Table 2. Table 2 Limit on the difference between diagonals Dimensions in millimetres Nominal glass thickness, d Limit on the difference between diagonals Stock sizes Splits (H, B) 1 500 1 500 3 000 6, 7, 8, 9 3 4 5 4.3 Wire mesh This is a square steel mesh welded at a

33、ll intersections of approximate dimensions 12,5 mm or 25,0 mm, manufactured from wire of diameter 0,42 mm. 5 Quality requirements 5.1 General One quality level is considered in this European Standard. This is determined by evaluation of the visual faults. There are three different types of pattern f

34、aults considered which may occur simultaneously. They are shown in Figure 2 and are a) out of square; b) waviness; c) bow. DIN EN 572-6:2012-11 EN 572-6:2012 (E) 7 There are three different types of deviation of the wire considered which may occur simultaneously. They are shown in Figure 3 and are d

35、) out of square, e) waviness, f) bow. 5.2 Methods of observation and measurement 5.2.1 Spot and linear/extended faults The glass pane to be examined is illuminated in conditions approximating to diffuse daylight and is observed in front of a matt grey screen. Place the pane of glass to be examined v

36、ertically 3 m in front of the parallel to the screen. Arrange the point of observation 1,5 m from the glass, keeping the direction of observation normal to the glass surface. View the pane of glass, and note the presence of visually disturbing faults. a) Spot faults Measure the dimensions of these f

37、aults with a micrometer with graduations in tenths of a millimetre. Note the number, dimensions and concentration of the spot faults. b) Linear/extended faults Note the number of these faults. 5.2.2 Pattern faults A reference, e.g. line or straight edge, is placed on the glass as shown in Figure 2.

38、The deviation, x, of the pattern in relation to this reference is measured. a) Out of square b) Waviness c) Bow NOTE The scale of these drawings has been exaggerated in order to be explicit about the types of deviation. Figure 2 Representations of the type of pattern faults 5.2.3 Wire faults A refer

39、ence, e.g. line or straight edge, is placed parallel to the direction of the wires. The deviation, y, of the wire in relation to this reference is measured (see Figure 3). DIN EN 572-6:2012-11 EN 572-6:2012 (E) 8 Any penetration of the glass surface by the wire is noted. Any breaks in the wire are n

40、oted. a) Out of square b) Waviness c) BowNOTE The scale of these drawings has been exaggerated in order to be explicit about the types of deviation. Figure 3 Representations of the types of wire faults 5.3 Acceptance levels 5.3.1 Spot faults Spot faults are categorized and found to be acceptable or

41、not acceptable as follows: a) Spherical and quasi-spherical spot faults: 1) If the larger dimension is 2,0 mm, they are acceptable without restriction; 2) If the larger dimension is 2,0 mm and 5,0 mm, they are acceptable up to 2 in any 1 m 1 m area;. 3) They are not acceptable if the larger dimensio

42、n is 5,0 mm. b) Elongated spot faults of width 2,0 mm: 1) If their length is 4,0 mm, they are acceptable without restriction; 2) If their length is 4,0 mm and 25,0 mm, they are acceptable if the sum of the lengths is 100 mm in any 1 m 1 m area; 3) They are not acceptable if the length is 25,0 mm. c)

43、 Elongated spot faults of width 2,0 mm: 1) If the larger dimension is 8,0 mm, they are acceptable up to 2 in any 1 m 1 m area; 2) They are not acceptable if the larger dimension is 8,0 mm. 5.3.2 Linear/extended faults The allowable number of faults is an average of 0,05 faults in 20 m of glass relat

44、ed to at least 20 tonnes. DIN EN 572-6:2012-11 EN 572-6:2012 (E) 9 5.3.3 Pattern faults The deviation of the pattern, x, (see Figure 2) shall not exceed 12 mm per metre. 5.3.4 Wire faults The deviation, y, (see Figure 3) shall not exceed 15 mm per metre. NOTE The deformation of the wires of each squ

45、are of the mesh is not considered. No penetration of the surface is acceptable. A break in the wire is acceptable only if it does not affect vision in a disturbing manner under the conditions of observation described in 5.2.1. 6 Designation Wired patterned glass in compliance with this European Stan

46、dard shall be designated respectively by type (mesh size), reference to this European Standard, tint (manufacturers reference) or clear, pattern (manufacturers reference), nominal thickness in mm, nominal length, H, and width, B, in mm EXAMPLE Wired patterned glass (12,5 mm), pattern reference PATTE

47、RN, clear, thickness 7 mm, length 3,30 m, width 1,80 m, intended for use in building, is designated as follows: Wired patterned glass (12,5 mm) - EN 572-6 - clear PATTERN, 7 mm, 3 300 mm 1 800 mm DIN EN 572-6:2012-11 EN 572-6:2012 (E) 10 Bibliography 1 EN 572-8, Glass in building Basic soda lime silicate glass products Part 8: Supplied and final cut sizes DIN EN 572-6:2012-11