CSA B342-2015 Selection and use of UN pressure receptacles and multiple-element gas containers for the transport of dangerous goods Class 2 (Second Edition).pdf

《CSA B342-2015 Selection and use of UN pressure receptacles and multiple-element gas containers for the transport of dangerous goods Class 2 (Second Edition).pdf》由会员分享，可在线阅读，更多相关《CSA B342-2015 Selection and use of UN pressure receptacles and multiple-element gas containers for the transport of dangerous goods Class 2 (Second Edition).pdf（56页珍藏版）》请在麦多课文档分享上搜索。

1、B342-15Selection and use of UN pressure receptacles, multiple-element gas containers, and other pressure receptacles for the transport of dangerous goods, Class 2Legal Notice for StandardsCanadian Standards Association (operating as “CSA Group”) develops standards through a consensus standards devel

2、opment process approved by the Standards Council of Canada. This process brings together volunteers representing varied viewpoints and interests to achieve consensus and develop a standard. Although CSA Group administers the process and establishes rules to promote fairness in achieving consensus, i

3、t does not independently test, evaluate, or verify the content of standards.Disclaimer and exclusion of liabilityThis document is provided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concernin

4、g this documents fitness for a particular purpose or use, its merchantability, or its non-infringement of any third partys intellectual property rights. CSA Group does not warrant the accuracy, completeness, or currency of any of the information published in this document. CSA Group makes no represe

5、ntations or warranties regarding this documents compliance with any applicable statute, rule, or regulation. IN NO EVENT SHALL CSA GROUP, ITS VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMA

6、GES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF

7、LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF CSA GROUP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, CSA Group is not undertaking to render professional o

8、r other services for or on behalf of any person or entity or to perform any duty owed by any person or entity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and CSA Group accepts no respo

9、nsibility whatsoever arising in any way from any and all use of or reliance on the information contained in this document. CSA Group is a private not-for-profit company that publishes voluntary standards and related documents. CSA Group has no power, nor does it undertake, to enforce compliance with

10、 the contents of the standards or other documents it publishes. Intellectual property rights and ownershipAs between CSA Group and the users of this document (whether it be in printed or electronic form), CSA Group is the owner, or the authorized licensee, of all works contained herein that are prot

11、ected by copyright, all trade-marks (except as otherwise noted to the contrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. Without limitation, the unauthorized u

12、se, modification, copying, or disclosure of this document may violate laws that protect CSA Groups and/or others intellectual property and may give rise to a right in CSA Group and/or others to seek legal redress for such use, modification, copying, or disclosure. To the extent permitted by licence

13、or by law, CSA Group reserves all intellectual property rights in this document.Patent rightsAttention is drawn to the possibility that some of the elements of this standard may be the subject of patent rights. CSA Group shall not be held responsible for identifying any or all such patent rights. Us

14、ers of this standard are expressly advised that determination of the validity of any such patent rights is entirely their own responsibility.Authorized use of this documentThis document is being provided by CSA Group for informational and non-commercial use only. The user of this document is authori

15、zed to do only the following:If this document is in electronic form:sLOADTHISDOCUMENTONTOACOMPUTERFORTHESOLEPURPOSEOFREVIEWINGITsSEARCHANDBROWSETHISDOCUMENTANDsPRINTTHISDOCUMENTIFITISIN0$(b) when UN pressure receptacles are required to be equipped with one or more pressure-relief devices, the pressu

16、re-relief device system(s) needs to be capable of preventing rupture of normally filled UN pressure receptacles that are subjected to a fire test;(c) UN pressure receptacles filled with a refrigerated liquefied gas or a liquefied flammable gas need to be transported in an upright position unless the

17、y are designed for horizontal service; and(d) the use of UN composite cylinders constructed in accordance with ISO 11119-3:2002, Gas cylinders of composite construction Specification and test methods Part 3: Fully wrapped fibre reinforced composite gas cylinders with non-load-sharing metallic or non

18、-metallic liners, is not authorized for toxic gases with an LC50less than 200 mL/m3.This Standard was prepared by the Subcommittee on UN Pressure Receptacles and Multiple-Element Gas Containers for the Transportation of Dangerous Goods, under the jurisdiction of the Technical Committee on Cylinders,

19、 Spheres, and Tubes for the Transport of Dangerous Goods and the Strategic Steering Committee on Mechanical and Industrial Equipment Safety, and has been formally approved by the Technical Committee.Notes: (1) Use of the singular does not exclude the plural (and vice versa) when the sense allows.(2)

20、 Although the intended primary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose.(3) This Standard was developed by consensus, which is defined by CSA Poli

21、cy governing standardization Code of good practice for standardization as “substantial agreement. Consensus implies much more than a simple majority, but not necessarily unanimity”. It is consistent with this definition that a member may be included in the Technical Committee list and yet not be in

22、full agreement with all clauses of this Standard.(4) To submit a request for interpretation of this Standard, please send the following information to inquiriescsagroup.org and include “Request for interpretation” in the subject line:(a) define the problem, making reference to the specific clause, a

23、nd, where appropriate, include an illustrative sketch;(b) provide an explanation of circumstances surrounding the actual field condition; and(c) where possible, phrase the request in such a way that a specific “yes” or “no” answer will address the issue.Committee interpretations are processed in acc

24、ordance with the CSA Directives and guidelines governing standardization and are available on the Current Standards Activities page at standardsactivities.csa.ca.(5) This Standard is subject to review five years from the date of publication. Suggestions for its improvement will be referred to the ap

25、propriate committee. To submit a proposal for change, please send the following information to inquiriescsagroup.org and include “Proposal for change” in the subject line:(a) Standard designation (number);(b) relevant clause, table, and/or figure number;(c) wording of the proposed change; and(d) rat

26、ionale for the change. 2015 CSA GroupSelection and use of UN pressure receptacles,multiple-element gas containers, and other pressurereceptacles for the transport of dangerous goods, Class 2September 2015 1B342-15Selection and use of UN pressure receptacles, multiple-element gas containers, and othe

27、r pressure receptacles for the transport of dangerous goods, Class 21Scope1.1This Standard specifies requirements for the selection, use, handling, and filling of UN pressure receptacles, multiple-element gas containers, and other pressure receptacles for the transport of dangerous goods included in

28、 Class 2, gases.1.2In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or

29、 that which is permissible within the limits of the Standard.Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.Notes to tables and figures are considered par

30、t of the table or figure and may be written as requirements.Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.2 Reference publicationsThis Standard refers to the following publications, and where such reference is made, it shall be to the edition

31、 listed below, including all amendments published thereto. Where there is an inconsistency between this Standard and a referenced publication other than the Transportation of Dangerous Goods Act and its regulations, the requirements of this Standard shall prevail. Users of this Standard should avoid

32、 directly applying a referenced publication without carefully considering this Standards reference to that publication.Note: See Annex A for information on the reference organizations.CSA GroupB341-15UN pressure receptacles and multiple-element gas containers for the transportation of dangerous good

33、sASME International (American Society of Mechanical Engineers)Boiler and Pressure Vessel Code, 2013B342-15 2015 CSA Group2 September 2015CCMTA (Canadian Council of Motor Transport Administrators)NSC-E-STND10-2010Cargo SecurementCGA (Compressed Gas Association)C-6-2013Standard for Visual Inspection o

34、f Steel Compressed Gas CylindersC-14-2005 (R2010)Procedures for Fire Testing of DOT Cylinder Pressure Relief Device SystemsG-1.6-2011Standard for Mobile Acetylene Trailer SystemsS-1.1-2011Pressure Relief Device Standards Part 1 Cylinders for Compressed GasesS-1.2-2009Pressure Relief Device Standards

35、 Part 2 Portable Containers for Compressed GasesS-7- 2013Standard Method for Selecting Pressure Relief Devices for Compressed Gas Mixtures in CylindersGovernment of CanadaTransportation of Dangerous Goods Act, 1992, SC 1992, c. 34Transportation of Dangerous Goods Regulations (including amendments) G

36、overnment of the United StatesTitle 49 of the Code of Federal Regulations of the United States, October 2014 (49 CFR)ISO (International Organization for Standardization)3807-1:2000Cylinders for acetylene Basic requirements Part 1: Cylinders without fusible plugs3807-2:2000Cylinders for acetylene Bas

37、ic requirements Part 2: Cylinders with fusible plugs4126-1:2004Safety devices for protection against excessive pressure Part 1: Safety valves7866:2012/Cor. 1:2014Gas cylinders Refillable seamless aluminium alloy gas cylinders Design, construction and testing10297:2006Transportable gas cylinders Cyli

38、nder valves Specification and type testing10460:2005Gas cylinders Welded carbon-steel gas cylinders Periodic inspection and testing10692-2:2001Gas cylinders Gas cylinder valve connections for use in the micro-electronics industry Part 2: Specification and type testing for valve to cylinder connectio

39、ns 2015 CSA GroupSelection and use of UN pressure receptacles,multiple-element gas containers, and other pressurereceptacles for the transport of dangerous goods, Class 2September 2015 311114-1:2012Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materia

40、ls11114-2:2013Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials11117:1998Gas cylinders Valve protection caps and valve guards for industrial and medical gas cylinders Design, construction and tests11117:2008/Cor 1:2009Gas cylin

41、ders Valve protection caps and valve guards Design, construction and tests11118:1999Gas cylinders Non-refillable metallic gas cylinders Specification and test methods11119-1:2012Gas cylinders Refillable composite gas cylinders and tubes Design, construction and testing Part 1: Hoop wrapped fibre rei

42、nforced composite gas cylinders and tubes up to 450 l11119-2:2012/A1:2014Gas cylinders Refillable composite gas cylinders and tubes Design, construction and testing Part 2: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l with load-sharing metal liners11119-3:2013Gas cyli

43、nders Refillable composite gas cylinders and tubes Design, construction and testing Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 L with non-load-sharing metallic or non-metallic liners11372:2011Gas cylinders Acetylene cylinders Filling conditions and filling ins

44、pection11513:2011Gas cylinders Refillable welded steel cylinders containing materials for sub-atmospheric gas packaging (excluding acetylene) Design, construction, testing, use and periodic inspection11621:1997Gas cylinders Procedures for change of gas service11755:2005Gas cylinders Cylinder bundles

45、 for compressed and liquefied gases (excluding acetylene) Inspection at time of filling13088:2011Gas cylinders Acetylene cylinder bundles Filling conditions and filling inspection13340:2001Transportable gas cylinders Cylinder valves for non-refillable cylinders Specification and prototype testing161

46、11:2008Transportable gas storage devices Hydrogen absorbed in reversible metal hydrideB342-15 2015 CSA Group4 September 201521029-2:2004Cryogenic vessels Transportable vacuum insulated vessels of not more than 1 000 litres volume Part 2: Operational requirements24431:2006Gas cylinders Cylinders for

47、compressed and liquefied gases (excluding acetylene) Inspection at time of fillingUN (United Nations)Recommendations on the Transport of Dangerous Goods Model Regulations, 18th ed. rev. (2013)3 DefinitionsThe following definitions shall apply in this Standard:Acetylene trailer an open transport vehi

48、cle designed to be towed that consists of a group or groups of acetylene cylinders secured in accordance with Part 1 of the National Safety Code (NSC) Standard 10, Cargo Securement, as adopted by provincial and territorial regulations in Canada, or Title 49 of the U.S. Code of Federal Regulations (49 CFR) 393.102, and manifolded together as a single unit, for filling, transporting, and delivering acetylene.Adsorbed gas a gas which when packaged for transport is adsorbed onto a solid porous material resulting in an internal receptacle pressure of less than 101.3 kPa at 20 C and less t