BS ISO 582-1995 Rolling bearings - Chamfer dimensions - Maximum values《滚动轴承 倒角尺寸 最大值》.pdf

《BS ISO 582-1995 Rolling bearings - Chamfer dimensions - Maximum values《滚动轴承 倒角尺寸 最大值》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 582-1995 Rolling bearings - Chamfer dimensions - Maximum values《滚动轴承 倒角尺寸 最大值》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS ISO 582:1995Implementation of ISO 582:1995Rolling bearings Chamfer dimensions Maximum valuesICS 21.100.20BS ISO +A1:2013BS ISO 582:1995+A1:2013ISBN 978 0 580 79175 8Amendments/corrigenda issued since publicationDate Comments31 July 2013 Implementation of ISO amendment 1:2013This B

2、ritish Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 November 1995 The British Standards Institution 2013. Published by BSI Standards Limited 2013National forewordThis British S

3、tandard is the UK implementation of ISO 582:1995+A1:2013. It supersedes BS ISO 582:1995, which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to ISO text carry the number of the ISO amendment. For example, text a

4、ltered by ISO amendment 1 is indicated by .The UK participation in its preparation was entrusted to Technical Committee MCE/7, Rolling bearings. A list of organizations represented on this committee can be obtained on request to its secretary.The publication does not purport to include all the neces

5、sary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.ISO 582:1995(E)ii BSI 11-1999ContentsPageForeword iiiIntroduction 11 Scope 12 Normative references 13 Definitions 14 Symbols and dimension

6、s 15 Shaft and housing fillet radii 1Figure 1 2Table 1 Radial bearings in accordance with ISO 15 3Table 2 Radial bearings in accordance with ISO 246 and ISO 464 and in accordance with ISO 12043 for loose ribs 3Table 3 Radial bearings in accordance with ISO 12043, inner and outer ring non-rib sides o

7、nly, and with ISO 12044 4Table 4 Tapered roller bearings in accordance with ISO 355, inner and outer ring back facesTable 5 Thrust bearings in accordance with ISO 104Descriptors: Bearings, rolling bearings, radial bearings, thrust bearings, chamfer, dimensions, metric system.BS ISO 582:1995+A1:2013i

8、i The British Standards Institution 201356ISO 582:1995(E) BSI 11-1999 iiiForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO tech

9、nical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely

10、 with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % o

11、f the member bodies casting a vote.International Standard ISO 582 was prepared by Technical Committee ISO/TC 4, Rolling bearings.This third edition cancels and replaces the second edition (ISO 582:1979), which has been technically revised.BS ISO 582:1995+A1:2013iii The British Standards Institution

12、2013ivblankISO 582:1995(E) BSI 11-1999 1IntroductionIn order to ensure that the chamfers on rolling bearings are compatible with the dimensions of parts which come into contact with the rolling bearings, values of the chamfer dimensions, of which the minimum limit is of primary interest to the beari

13、ng user and application designer, are required.The purpose of this International Standard is to achieve interchangeability of rolling bearings, by specifying the chamfer dimensions, and to minimize the risk of incompatibility in bearing applications.1 ScopeThis International Standard specifies the m

14、aximum chamfer dimensions of metric series rolling bearings, for which boundary dimensions, including chamfer minimum dimensions, are given in other International Standards. Requirements for the maximum dimensions of the corresponding shaft and housing fillet radii are also given.It does not apply t

15、o chamfers, for which dimensions are not specified, or for which other dimensions are specified in other International Standards.2 Normative referencesThe following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time o

16、f publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain

17、 registers of currently valid International Standards.ISO 15:1981, Rolling bearings Radial bearings Boundary dimensions General plan. ISO 104:1994, Rolling bearings Thrust bearings Boundary dimensions, general plan. ISO 246:1995, Rolling bearings Cylindrical roller bearings, separate thrust collars

18、Boundary dimensions. ISO 355:1977, Rolling bearings Metric tapered roller bearings Boundary dimensions and series designations. ISO 464:1995, Rolling bearings Radial bearings with locating snap ring Dimensions and tolerances. ISO 12043:1995, Rolling bearings Single-row cylindrical roller bearings Ch

19、amfer dimensions for loose-rib and non-rib sides. ISO 12044:1995, Rolling bearings Single-row angular contact ball bearings Chamfer dimensions for outer ring non-thrust side. 3 DefinitionsFor the purposes of this International Standard, the following definitions apply.3.1 radial direction chamfer di

20、mension (of a bearing ring or washer)the distance between the imaginary sharp ring or washer corner and the intersection of the chamfer surface and the ring or washer face3.2 axial direction chamfer dimension (of a bearing ring or washer)the distance between the imaginary sharp ring or washer corner

21、 and the intersection of the chamfer surface and the bore or outside cylindrical surface of the ring or washer4 Symbols and dimensionsSee Figure 1 and Table 1 to Table 5.The dimensions given in Table 1 to Table 5 corresponding to symbols shown in Figure 1 are nominal dimensions unless specified othe

22、rwise.5 Shaft and housing fillet radiiThe largest permissible single shaft and housing fillet radius ras maxshould not exceed the smallest permissible single chamfer dimension of the corresponding ring or washer rs minor r1s min.BS ISO 582:1995+A1:20131 The British Standards Institution 2013ISO 355,

23、 Rolling bearings Tapered roller bearings Boundary dimensions and series ISO 582:1995(E)2 BSI 11-1999d = bore diameterD = outside diameterrs min, r1s min= smallest permissible single chamfer dimension of rs, r1s(single chamfer dimension)rs max, r1s max= largest permissible single chamfer dimension o

24、f rs, r1sras max= largest permissible single shaft and housing fillet radius.NOTE The exact shape of the chamfer surface is not specified, but its contour in an axial plane shall not be allowed to project beyond the imaginary circular arc, of radius rs minor r1s min, tangential to the ring or washer

25、 face and the bore or outside cylindrical surface of the ring or washer.Figure 1 BS ISO 582:1995+A1:2013 The British Standards Institution 2013ISO 582:1995(E) BSI 11-1999 3Table 1 Radial bearings in accordance with ISO 15Table 2 Radial bearings in accordance with ISO 246 and ISO 464 and in accordanc

26、e with ISO 12043 for loose ribsDimensions in millimetresrs minad rs maxbDirectionsradial axial0,050,080,10,150,20,10,160,20,30,50,20,30,40,60,80,3d 40d 400,60,8110,6d 40d 4011,3221d 50d 501,51,9331,1d 120d 12022,53,541,5d 120d 1202,33452d 8080 22033,53,84,5562,1d 280d 28044,56,572,5cd 100100 2803,84

27、,556673d 280d 28055,5884567,59,51215196,581012,515182125910131719243038a See clause 5 for maximum shaft and housing fillet radii.b For bearings with a width of2mm or less the rs maxvalues for the radial direction apply also in the axial direction.c This chamfer dimension is not specified in ISO 15.D

28、imensions in millimetresr1s minad or D r1s maxDirectionsradial axial0,2 0,5 0,50,3d or D 40 0,6 0,8d or D 40 0,8 0,80,5d or D 40 1 1,5d or D 40 1,3 1,50,6d or D 40 1 1,5d or D 50 1,9 2,21,1d or D 120 2 2,7d or D 120 2,5 2,71,5d or D 120 2,3 3,5d or D 120 3 3,52d or D 80 3 480 220 3,8 42,1d or D 280

29、4 4,5d or D 280 4,5 4,52,5bd or D 100 3,8 5100 280 5 53d or D 280 5 5,5d or D 280 5,5 5,54 6,5 6,55 8 86 10 10a See clause 5 for maximum shaft and housing fillet radii.b This chamfer dimension is not specified in ISO 246, ISO 464 and ISO 12043.BS ISO 582:1995+A1:20133 The British Standards Instituti

30、on 2013ISO 582:1995(E)4 BSI 11-1999Table 3 Radial bearings in accordance with ISO 12043, inner and outer ring non-rib sides only, and with ISO 12044Table 4 Tapered roller bearings in accordance with ISO 355, inner and outer ring back facesDimensions in millimetresr1s minad or D r1s maxDirectionsradi

31、al axial0,1 0,2 0,40,15 0,3 0,60,2b 0,5 0,80,3d or D 40 0,6 1d or D 40 0,8 10,6d or D 40 1 2d or D 40 1,3 21d or D 50 1,5 3d or D 50 1,9 31,1d or D 120 2 3,5d or D 120 2,5 41,5d or D 120 2,3 4d or D 120 3 52d or D 80 3 4,580 220 3,8 6a See clause 5 for maximum shaft and housing fillet radii.b This c

32、hamfer dimension is not specified in ISO 12043 and ISO 12044.Dimensions in millimetresrs minad or D rs maxDirectionsradial axial0,3d or D 40 0,7 1,4d or D 40 0,9 1,60,6d or D 40 1,1 1,7d or D 40 1,3 21d or D 50 1,6 2,5d or D 50 1,9 31,5d or D 120 2,3 3120 250 3,5 42d or D 120 2,8 4120 250 4 52,5d or

33、 D 120 3,5 5120 250 4,5 63d or D 120 4 5,5120 400 5,5 7,54d or D 120 5 7120 400 6,5 8,55d or D 180 6,5 8d or D 180 7,5 96d or D 180 7,5 10d or D 180 9 11a See clause 5 for maximum shaft and housing fillet radii.BS ISO 582:1995+A1:2013 The British Standards Institution 2013ISO 582:1995(E) BSI 11-1999

34、 5Table 5 Thrust bearings in accordance with ISO 104Dimensions in millimetresrs minaor r1s minars maxor r1s maxRadial and axial directions0,3 0,80,6 1,51 2,21,1 2,71,5 3,52 42,1 4,53 5,54 6,55 86 107,5 12,59,5 1512 1815 2119 25NOTE The dimensions given above refer to:a) back face/outside cylindrical

35、 surface chamfer of housing washer;b) back face/bore surface chamfer of shaft washer of single direction bearings;c) face/bore surface chamfers of central shaft washer of double direction bearings.a See clause 5 for maximum shaft and housing fillet radii.BS ISO 582:1995+A1:20135 The British Standard

36、s Institution 2013ISO 582:1995/Amd.1:2013(E)Dimensions in millimetresrs minor r1s min1)d or D rs maxor r1s maxDirectionsradial axial0,3d or D 40 d or D 400,7 0,91,4 1,60,5d or D 40 d or D 401,1 1,21,7 1,90,6d or D 40 d or D 401,1 1,31,7 21d or D 50 d or D 501,6 1,92,5 31,5d or D 120 120 2502,3 2,8 3

37、,53 3,5 42d or D 120 120 2502,8 3,5 44 4,5 52,5d or D 120 120 2503,5 4 4,55 5,5 63d or D 120 120 4004 4,5 5 5,55,5 6,5 7 7,53,3d or D 120 120 4004,3 4,8 5,3 5,86,3 6,8 7,3 7,84d or D 120 120 4005 5,5 6 6,57 7,5 8 8,55d or D 180 d or D 1806,5 7,58 96d or D 180 d or D 1807,5 910 117d or D 180 d or D 1

38、8010 11,512,5 13,58d or D 180 d or D 18012,5 14,515,5 17,51)See Clause 5 for maximum shaft and housing fillet radii.2 ISO 2013 All rights reservedTable 4 Tapered roller bearings in accordance with ISO 355, inner and outer ring back facesISO 582:1995(E) BSI 11-1999 5Table 5 Thrust bearings in accorda

39、nce with ISO 104Dimensions in millimetresrs minaor r1s minars maxor r1s maxRadial and axial directions0,3 0,80,6 1,51 2,21,1 2,71,5 3,52 42,1 4,53 5,54 6,55 86 107,5 12,59,5 1512 1815 2119 25NOTE The dimensions given above refer to:a) back face/outside cylindrical surface chamfer of housing washer;b

40、) back face/bore surface chamfer of shaft washer of single direction bearings;c) face/bore surface chamfers of central shaft washer of double direction bearings.a See clause 5 for maximum shaft and housing fillet radii.BS ISO 582:1995+A1:20136 The British Standards Institution 2013blankBS ISO 582:19

41、95BSI389 Chiswick High RoadLondonW4 4ALBSIBritish Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are u

42、pdated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Briti

43、sh Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the l

44、atest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.In response to orders for international standards, it is BSI policy to supply the BSI implementation of th

45、ose that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information service

46、s are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For detail

47、s of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyrig

48、ht, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the sta

49、ndard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996