BS ISO 5749-2004 Pliers and nippers - Diagonal cutting nippers - Dimensions and test values《夹扭钳和剪切钳 斜嘴钳 尺寸和试验值》.pdf

《BS ISO 5749-2004 Pliers and nippers - Diagonal cutting nippers - Dimensions and test values《夹扭钳和剪切钳 斜嘴钳 尺寸和试验值》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 5749-2004 Pliers and nippers - Diagonal cutting nippers - Dimensions and test values《夹扭钳和剪切钳 斜嘴钳 尺寸和试验值》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 5749:2004 Pliers and nippers Diagonal cutting nippers Dimensions and test values ICS 25.140.30 BS ISO 5749:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 10 December 2004 BSI 10 December 2004 ISBN 0 580 45042 2 N

2、ational foreword This British Standard reproduces verbatim ISO 5749:2004 and implements it as the UK national standard. It supersedes BS 3087-9:1986 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee MTE/15, Hand tools, to Subcommittee MTE/15/13, Assembl

3、y tools for screws and nuts, pliers and nippers, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may b

4、e found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are

5、 responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and

6、keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 7 and a back cover. The BSI copyright n

7、otice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 5749:2004(E)INTERNATIONAL STANDARD ISO 5749 Third edition 2004-09-15 Pliers and nippers Diagonal cutting nippers Dimensions and test values Pi

8、nces et tenailles Pinces coupantes diagonales Dimensions et valeurs dessai BSISO5749:2004DPlcsid Fremia ihTs PDF file mya ctnoian emdebt dedyfepcaes. In ccacnadrow eitA hebods licnesilop gnic,y tihs file mirp eb yatnde iv roweb detu slahl ton ide ebtlnu deess teh typfecaes wihce era hml era deddebic

9、snede ti dna onstlalde t noeh comuptfrep reromign tide ehtin.g In wodlnidaot gnihs fil,e trapise atpecc tiereht nser ehnopsiiblity fo nto ifnriigngn Aebods licnesilop gnic.y ehT ISO tneClar Secrteirata caceptl on siibality in this .aera Ai ebods a tedarmfo kra Aebod SystemI snctaropro.de teDials fo

10、teh sfotwcudorp erats sut deo crtaee tihs PDF file cna f ebi dnuon tlareneG eh Ifnler oatit evt oeh file; tP ehDc-Frtaeino marapterew stpo ereimizde fro irptni.gn Evyre cera neeb sah takne tsne oeru taht teh file is siutlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem lertait

11、gno it is f,dnuo plsaee ifnrom ttneC ehlar Secterirata ta teh serddaig sleb nevwo. ii BSISO5749:2004 iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is norma

12、lly carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in th

13、e work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare

14、International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some

15、of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5749 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pliers and nippers. This

16、 third edition cancels and replaces the second edition (ISO 5749:1988) which has been technically revised. BSISO5749:2004blankINTENRATIONAL TSANDADR IS:9475 O4002(E)1Pliers and nippers Diagonal cutting nippers Dimensions and test values 1 Scope This International Standard specifies the principal dim

17、ensions of diagonal cutting nippers and the test values for the nippers in order to verify their aptitude to function in conformity with ISO 5744. General technical requirements are given in ISO 5743. The diagonal cutting nippers illustrated in this International Standard are examples only and are n

18、ot intended to affect the manufacturers design. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

19、 amendments) applies. ISO 5743, Pliers and nippers General technical requirements ISO 5744:2004, Pliers and nippers Methods of test 3 Dimensions and test values 3.1 Diagonal cutting nippers for hard wire The main dimensions for cutting nippers for hard wire are shown in Figure 1 and given in Table 1

20、. The cutting nippers shall be tested in accordance with ISO 5744. After the load test, the permanent set s shall not exceed the value given in Table 2. If distance l 1is not suitable for the load test, the formula given in ISO 5744:2004, 4.2 shall be used. The cutting force, F 1 , and the diameter,

21、 d, of the test wire shall not exceed the values given in Table 2. Nippers having a lever ratio differing from the values given in Table 2 shall be checked for compliance using the formula given in ISO 5744:2004, 5.3.3. BSISO5749:20042 Dimensions in millimetres aF = Load applied in load test or F 1f

22、orce applied in cutting test. Figure 1 Diagonal cutting nippers for hard wire Table 1 Diagonal cutting nippers for hard wire, main dimensions Dimensions in millimetres l l 3w 3t 1max. max. max. 125 6 18 22 10 140 7 20 25 11 160 8 22 28 12 180 9 25 32 14 200 10 28 36 16 Table 2 Diagonal cutting nippe

23、rs for hard wire, force application and test values Cutting test Load test Nominal length l l 1l 2Diameter of hard test wire daMaximum cutting force F 1 maxLoad F Maximum permanent set s max bmm mm mm mm N N mm 125 80 10 1,25 500 800 0,5 140 90 11 1,4 575 900 1 160 100 12,5 1,6 700 1 000 1 180 112 1

24、4 1,8 850 1 120 1 200 125 16 2 1 020 1 250 1 aData for hard test wire are given in ISO 5744. bs = w 1 w 2(see ISO 5744). BSISO5749:2004 33.2 Diagonal cutting nippers for medium hard wire The main dimensions for cutting nippers for hard wire are shown in Figure 2 and given in Table 3. The cutting nip

25、pers shall be tested in accordance with ISO 5744. After the load test, the permanent set s shall not exceed the value given in Table 4. If distance l 1is not suitable for the load test, the formula given in ISO 5744:2004, 4.2 shall be used. The cutting force, F 1 , and the diameter, d, of the test w

26、ire shall not exceed the values given in Table 4. Nippers having a lever ratio differing from the values given in Table 4 shall be checked for compliance using the formula given in ISO 5744:2004, 5.3.2. Dimensions in millimetres aF = Load applied in load test or F 1force applied in cutting test. Fig

27、ure 2 Diagonal cutting nippers for medium hard wire Table 3 Diagonal cutting nippers for medium hard wire, main dimensions Dimensions in millimetres l l 3w 3t 1max. max. max. 125 6 18 22 10 140 7 20 25 11 160 8 22 28 12 180 9 25 32 14 200 10 28 36 16 BSISO5749:20044 Table 4 Diagonal cutting nippers

28、for medium hard wire, force application and test values Cutting test Load test Nominal length l l 1l 2Diameter of medium hard test wire daMaximum cutting force F 1 maxLoad F Maximum permanent set s max bmm mm mm mm N N mm 125 80 12,5 1,6 450 800 0,5 140 90 14 1,6 450 900 1 160 100 16 1,6 460 1 000 1

29、 180 112 18 1,6 460 1 120 1 200 125 20 1,6 460 1 250 1 aData for medium hard test wire are given in ISO 5744. bs = w 1 w 2(see ISO 5744). 3.3 Toggle lever assisted side cutting nippers for hard wire The main dimensions for cutting nippers for hard wire are shown in Figure 3 and given in Table 5. The

30、 cutting nippers shall be tested in accordance with ISO 5744. After the load test, the permanent set s shall not exceed the value given in Table 6. If distance l 1is not suitable for the load test, the formula given in ISO 5744:2004, 4.2 shall be used. The cutting force, F 1 , and the diameter, d, o

31、f the test wire shall not exceed the values given in Table 6. Nippers having a lever ratio differing from the values given in Table 6 shall be checked for compliance using the formula given in ISO 5744:2004, 5.3.4. BSISO5749:2004 5Dimensions in millimetres aF = Load applied in load test or F 1force

32、applied in cutting test. Figure 3 Toggle lever assisted side cutting nippers for hard wire Table 5 Toggle lever assisted side cutting nippers for hard wire, main dimensions Dimensions in millimetres l l 3w 3g t 1max. max. min. max. 200 10 25 45 5 18 224 11 28 48 6 18 Table 6 Toggle lever assisted si

33、de cutting nippers for hard wire, force application and test values Cutting test Load test Nominal length l l 1l 2Lever ratio aDiameter of hard test wire dbMaximum cutting force F 1 maxLoad F Maximum permanent set s max cmm mm mm mm N N mm 200 140 18 14,5 2,5 690 840 1 224 160 20 16,5 2,5 790 950 1

34、aThe lever ratio is equal to (w 5 w 1 )/g. b Data for hard test wire are given in ISO 5744. c s = w 1 w 2(see ISO 5744). BSISO5749:20046 4 Designation EXAMPLE 1 Diagonal cutting nippers, number 101 in accordance with ISO 5742, with a nominal length of 140 mm and for hard wire (H) are designated as f

35、ollows: Diagonal cutting nippers 101 - ISO 5749 - 140 - H EXAMPLE 2 Diagonal cutting nippers, number 101 in accordance with ISO 5742, with a nominal length of 160 mm and for medium wire (M) are designated as follows: Diagonal cutting nippers 101 - ISO 5749 - 160 - M EXAMPLE 3 Toggle lever assisted s

36、ide cutting nippers, number 105 in accordance with ISO 5742, with a nominal length of 200 mm are designated as follows: Toggle lever assisted side cutting nippers 105 - ISO 5749 - 200 5 Marking Marking shall be in accordance with ISO 5743. BSISO5749:2004 7Bibliography 1 ISO 5742, Pliers and nippers

37、Nomenclature BSISO5749:2004BS ISO 5749:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated b

38、y Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone findin

39、g an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called

40、 PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standard

41、s are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of

42、information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111.

43、 Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (

44、0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also

45、holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recor

46、ding or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.