BS ISO 3466-2016 Machine taper pin reamers with parallel shanks《带有直柄的机用推拔销绞刀》.pdf

《BS ISO 3466-2016 Machine taper pin reamers with parallel shanks《带有直柄的机用推拔销绞刀》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 3466-2016 Machine taper pin reamers with parallel shanks《带有直柄的机用推拔销绞刀》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 3466:2016Machine taper pin reamerswith parallel shanksBS ISO 3466:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 3466:2016. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and

2、 inserts for cutting applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Instit

3、ution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 90181 2 ICS 25.100.30 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2016.Amendments/c

4、orrigenda issued since publicationDate Text affectedBS ISO 3466:2016 ISO 2016Machine taper pin reamers with parallel shanksAlsoirs machine pour trous de goupilles coniques, queue cylindriqueINTERNATIONAL STANDARDISO3466Second edition2016-03-01Reference numberISO 3466:2016(E)BS ISO 3466:2016ISO 3466:

5、2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or

6、posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +4

7、1 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 3466:2016ISO 3466:2016(E)Foreword iv1 Scope . 12 Normative references 13 Driving tenons . 14 Dimensions . 1Annex A (informative) Relationship between designations in this International Standard and ISO 13399 . 3Bibliography 4 ISO 2016 All rights reserv

8、ed iiiContents PageBS ISO 3466:2016ISO 3466:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each

9、 member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internationa

10、l Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different t

11、ypes of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not b

12、e held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is inform

13、ation given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the

14、 following URL: Foreword - Supplementary information.The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Cutting tools with defined cutting edges, cutting items.This second edition cancels and replaces the first edition (ISO 3466:1975), of which it constitutes a

15、 minor revision.iv ISO 2016 All rights reservedBS ISO 3466:2016INTERNATIONAL STANDARD ISO 3466:2016(E)Machine taper pin reamers with parallel shanks1 ScopeThis International Standard lays down the dimensions of machine taper pin reamers with parallel shanks.It covers only metric dimensions, which ar

16、e the only recommended dimensions in the future for these types of reamers.The reamers have been designed to produce holes for taper pins manufactured to ISO 2339, in the range of 2 mm to 12 mm nominal diameter.Unless otherwise stated, these reamers will be right-hand cutting.The flutes may be strai

17、ght or left-hand spiral at the option of the manufacturer.Hand taper pin reamers are dealt with in ISO 3465, and machine taper pin reamers with Morse taper shanks in ISO 3467.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indis

18、pensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 4203, Parallel shank tools Driving tenons and sockets Dimensions3 Driving tenonsThe dimensions of the drivi

19、ng tenons for machine taper pin reamers with parallel shanks, when required, shall be in accordance with ISO 4203.4 Dimensions1Ldytyldddld1:50Key1 tenon dimensions in accordance with ISO 4203Figure 1 ISO 2016 All rights reserved 1BS ISO 3466:2016ISO 3466:2016(E)Table 1Dimensions in millimetresd d1t

20、y y1d2d3l1d4l2Lnominal h9 2 2,7 35 5 8 1,9 2,86 48 3,15 29 862,5 3,2 35 5 8 2,4 3,36 48 3,15 29 863 3,9 45 5 8 2,9 4,06 58 4,0 32 1004 5,1 55 5 8 3,9 5,26 68 5,0 34 1125 6,2 60 5 8 4,9 6,36 73 6,3 38 1226 7, 8 90 5 10 5,9 8,00 105 8,0 42 1608 10,6 130 5 10 7,9 10,80 145 10,0 46 20710 13,2 160 5 10 9

21、,9 13,40 175 12,5 50 24512 15,6 180 10 20 11,8 16,00 210 16,0 58 2902 ISO 2016 All rights reservedBS ISO 3466:2016ISO 3466:2016(E)Annex A (informative) Relationship between designations in this International Standard and ISO 13399For relationship between designations in this International Standard a

22、nd preferred symbols according to ISO 13399, see Table A.1.Table A.1 Relationship between designations in this International Standard and ISO 13399 seriesSymbol in ISO 3466Reference in ISO 3466Property name in ISO 13399Symbol in ISO 13399Reference in ISO 13399d Figure 1 and Table 1 cutting diameter

23、DCISO/TS 13399-371CE7A96D9F7Dd1Figure 1 and Table 1taper diameter largestDTAXISO/TS 13399-3726E3AA6C4A1Cd2Figure 1 and Table 1interference cutting diameterDCINTFISO/TS 13399-3726E2FCC0EC78d3Figure 1 and Table 1cutting diameter maximumDCXISO/TS 13399-371D084656CE32d4Figure 1 and Table 1connection dia

24、meter machine sideDCONMSISO/TS 13399-371EBDBF5060E6L Figure 1 and Table 1 overall length OALISO/TS 13399-371D078EB7C086l1Figure 1 and Table 1 usable length LUISO/TS 13399-371EBB33490FDAl2Figure 1 and Table 1 shank length LSISO/TS 13399-371CF298870946t Figure 1 and Table 1 taper length y Figure 1 and

25、 Table 1distance reference point PKLDCISO/TS 13399-3726E3AAAF99A3y1Figure 1 and Table 1 1:50 Figure 1 taper gradient TGISO/TS 13399-371CEAEC02FEBD ISO 2016 All rights reserved 3BS ISO 3466:2016ISO 3466:2016(E)Bibliography1 ISO 2861, Geometrical product specifications (GPS) ISO code system for tolera

26、nces on linear sizes Part 1: Basis of tolerances, deviations and fits2 ISO 2339, Taper pins, unhardened3 ISO 3465, Hand taper pin reamers4 ISO 3467, Machine taper pin reamers with Morse taper shanks5 ISO/TS 13399-3:2014, Cutting tool data representation and exchange Part 3: Reference dictionary for

27、tool items4 ISO 2016 All rights reservedBS ISO 3466:2016BS ISO 3466:2016ISO 3466:2016(E) ISO 2016 All rights reservedICS 25.100.30Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, info

28、rmation and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, governm

29、ent, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across

30、all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying s

31、tandardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard

32、 copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and

33、 adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription forma

34、t, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, p

35、lease visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .Rev

36、isionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Cen

37、tre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licen

38、sed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior w

39、ritten permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW