BS ISO 3342-2011 Textile glass Mats Determination of tensile breaking force《纺织玻璃纤维 织物 抗拉强度的测定》.pdf

《BS ISO 3342-2011 Textile glass Mats Determination of tensile breaking force《纺织玻璃纤维 织物 抗拉强度的测定》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 3342-2011 Textile glass Mats Determination of tensile breaking force《纺织玻璃纤维 织物 抗拉强度的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 3342:2011Textile glass Mats Determination of tensilebreaking forceBS ISO 3342:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 3

2、342:2011. Itsupersedes BS ISO 3342:1995 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/42, Fibre reinforced thermosetting plastics andprepregs.A list of organizations represented on this committee can beobtained on request to its secretary.This pub

3、lication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 74662 8ICS 59.100.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the a

4、uthority of theStandards Policy and Strategy Committee on 31 December 2011.Amendments issued since publicationDate Text affectedBS ISO 3342:2011Textile glass Mats Determination of tensile breaking forceVerre textile Mats Dtermination de la force de rupture en traction ISO 2011Reference numberISO 334

5、2:2011(E)Fourth edition2011-12-01ISO3342INTERNATIONAL STANDARDBS ISO 3342:2011ISO 3342:2011(E)COPYRIGHT PROTECTED DOCUMENT ISO 2011All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, includi

6、ng photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in Swi

7、tzerlandii ISO 2011 All rights reservedBS ISO 3342:2011ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees.

8、Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internat

9、ional Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standar

10、ds adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject o

11、f patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 3342 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres.This fourth edition cancels and replaces the third edition (ISO 3342:1995), of wh

12、ich it constitutes a minor revision. The main changes are as follows:a) the normative references have been updated;b) former Subclauses 5.2, 5.3 and 5.6 have been deleted;c) explanatory footnotes concerning the terms “elementary unit” and “laboratory sample” have been added.ISO 3342:2011(E) ISO 2011

13、 All rights reserved iiiBS ISO 3342:2011BS ISO 3342:2011INTERNATIONAL STANDARD ISO 3342:2011(E)Textile glass Mats Determination of tensile breaking force1 ScopeThis International Standard specifies a method for the determination of the tensile breaking force of textile glass mats.The method is inten

14、ded for chopped-strand mat but is equally applicable to certain types of continuous-strand mat usually intended for pultrusion.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For un

15、dated references, the latest edition of the referenced document (including any amendments) applies.ISO 291, Plastics Standard atmospheres for conditioning and testing3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1tensile breaking forcemaximum f

16、orce required to break the test specimen in a tensile test carried to ruptureNOTE It is generally expressed in newtons.4 PrincipleA pre-conditioned test specimen of standard dimensions is subjected to tension by a suitable mechanical device which indicates the tensile breaking force on a recorder or

17、 scale.NOTE The test results might vary significantly depending on whether they are obtained on rolls of mat or on the mat prior to winding into rolls (normally, the result is higher prior to winding). The method specified in this International Standard describes the procedure for testing rolls of m

18、at.5 Apparatus5.1 Tensile-testing machine.5.1.1 All testing machines shall include the following elements.a) A pair of suitable clamps to grip the specimen. They shall have a width of 160 mm and a minimum depth of 25 mm. The faces of the clamps shall be plane and parallel, shall ensure uniform press

19、ure over the whole width of the test specimen and shall prevent it from slipping. The clamps shall also ensure, at all times, alignment of the axis of the test specimen with the direction of the applied force. The initial distance between the clamps shall be 200 mm.b) A means for applying tension to

20、 the specimen. ISO 2011 All rights reserved 1BS ISO 3342:2011c) A mechanism that will continuously indicate or record the force sustained by the specimen. The mechanism shall be practically free from inertia at the specified speed of testing and shall indicate the force with an accuracy within 1 % o

21、f the true value.The reference machine is one having a constant rate of extension. Other types of test machine exist, e.g. with constant rate of loading or constant rate of traverse. If only such machines are available, they may be used subject to agreement between interested parties, but the result

22、s from different types of machine cannot necessarily be compared.5.1.2 The maximum error in the indicated force, at any point in the range in which the machine is used, shall not exceed 1 % of the true force. The error in the length of specimen exposed between the clamps shall not exceed 2 mm. The a

23、ccuracy of the tensile-testing machine shall be verified, for example by means of calibrated springs with appropriate characteristics.5.2 Template for cutting out specimens.For chopped-strand mat: polished template 150 mm wide and 316 mm long.For continuous-strand mat for pultrusion applications: po

24、lished template 75 mm wide and 316 mm long.5.3 Suitable trimming tool.For example a knife, scissors or a disc cutter.6 Conditioning and test atmosphere6.1 ConditioningCondition the material under test in one of the standard laboratory atmospheres specified in ISO 291 at the rate of 16 h for an eleme

25、ntary unit1); 1 h for test specimens or a laboratory sample2).Indicate in the test report the conditioning atmosphere chosen.6.2 Test atmosphereCarry out the tests in one of the standard laboratory atmospheres specified in ISO 291.The provisions of Subclauses 6.1 and 6.2 do not have to be used for r

26、outine quality control purposes at fabrication. In this case, the person responsible for the laboratory shall assess the influence of the actual conditions (temperature, humidity) on the results obtained. When drawing up specifications, and for any testing done in formal relationwith these specifica

27、tions, the standard conditioning specified above shall be used.7 Test specimensBefore preparing any test specimens, remove and discard from the roll at least two layers of mat to obtain an area free from any darnage. From this area, cut a strip at least 400 mm wide, using the trimming tool (5.3). Ha

28、ndle this strip with great care in order to avoid creasing it. Take the same precautions with the test specimens cut out as described below.1) The elementary unit is normally the smallest entity of a given product that is commercially available.2) A laboratory sample is a part of the elementary unit

29、 from which the specimen(s) will be selected for the test. A laboratory sample is taken when it is impractical to bring the elementary unit into the test laboratory.ISO 3342:2011(E)2 ISO 2011 All rights reservedBS ISO 3342:2011Using the template (5.2), cut from this strip test specimens 150 mm wide

30、(or 75 mm for continuous-strand mat) and 316 mm long, with the major axis of the specimens lying parallel to the longitudinal direction of the mat. If additional tests are to be made with the major axis of the specimens parallel to the transverse direction of the mat, cut out specimens 316 mm long a

31、cross the mat width. Cut out these specimens ensuring that they are equidistant from each other and are not less than 10 mm from the edges in the case of trimmed mats.In the case of continuous-strand mat, use only longitudinal specimens, i.e. specimens with their major axis parallel to the longitudi

32、nal direction of the mat.By default, one determination of the tensile breaking force shall be based on five specimens or more, depending on the width of the mat.If the width of the mat does not allow sufficient test specimens to be taken side by side, selection may be completed by cutting specimens

33、from additional strips, again ensuring that the specimens are evenly distributed.It might be convenient to cut the specimens from those which have been used to determine the mass per unit area of the mat in accordance with ISO 3374. In this case, ensure that the specimens are handled with care.The p

34、roduct specification or the persons ordering the test might require other methods of preparation of the test specimens. If so, these shall be described in the test report.8 Procedure8.1 Adjust the distance between the clamps to give a free specimen length of 200 mm.8.2 Adjust the speed of the testin

35、g machine to give a rate of clamp separation of 200 mm/min 10 mm/min.8.3 Ensure that the clamps are properly aligned.Position the specimen in the clamps so that the longitudinal axis of the specimen is aligned with the mechanical axis of the tensile tester.Tighten the clamps, evenly and firmly, appl

36、ying a slight tension to the specimen so that it is straight.Start the tensile tester and stretch the specimen to the point of rupture.Record the force, in newtons, required to break the specimen.Discard results obtained from test specimens that break within 10 mm of the clamps or that slip in the c

37、lamps, and test an appropriate number of additional specimens so as to obtain the required number of results (see Clause 7).If the break is not a clean one, this shall be noted in the test report.9 Expression of resultsCalculate the tensile breaking force, in newtons, of the mat as the mean of the i

38、ndividual values obtained for each test specimen, and round the mean to the nearest 1 N.If required, calculate the range of the results obtained for the specimens from a particular elementary unit.10 PrecisionThe precision of this test method is not known because interlaboratory data are not availab

39、le. When such data are obtained, a precision statement will be added at the following revision.ISO 3342:2011(E) ISO 2011 All rights reserved 3BS ISO 3342:201111 Test reportThe test report shall include the following information:a) a reference to this International Standard;b) all details necessary f

40、or the complete identification of the mat tested;c) the number of specimens tested;d) the conditioning and test atmospheres chosen;e) the type of tensile-testing machine used, the capacity of the machine and the scale range used;f) the tensile breaking force in the longitudinal direction and, if app

41、licable, in the transverse direction of the mat;g) if required, the range of the results for the specimens from the same elementary unit;h) a note describing the rupture of the specimen if the break is not a clean one; i) details of any operation not specified in this International Standard as well

42、as of any incident liable to have affected the results;j) the date of the test;k) any other relevant information.ISO 3342:2011(E)4 ISO 2011 All rights reservedBS ISO 3342:2011Bibliography1 ISO 3374, Reinforcement products Mats and fabrics Determination of mass per unit areaISO 3342:2011(E) ISO 2011

43、All rights reserved 5BS ISO 3342:2011ISO 3342:2011(E) ISO 2011 All rights reservedICS 59.100.10Price based on 5 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It

44、 presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated

45、 by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British St

46、andard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive th

47、e latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be

48、 addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBS

49、I provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to d