BS ISO 16366-2008 Tools for pressing - L-shaped guides《冲压工具 L形导向器》.pdf
《BS ISO 16366-2008 Tools for pressing - L-shaped guides《冲压工具 L形导向器》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 16366-2008 Tools for pressing - L-shaped guides《冲压工具 L形导向器》.pdf(12页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARDBS ISO 16366:2008Tools for pressing L-shaped guidesICS 25.120.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS ISO 16366:2008Thi
2、s British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2008 BSI 2008ISBN 978 0 580 57162 6National forewordThis British Standard is the UK implementation of ISO 16366:2008. It supersedes BS ISO 16366:2001 which is withdrawn.The UK participatio
3、n in its preparation was entrusted to Technical Committee MTE/12, Tools for pressing and moulding.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are respo
4、nsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsReference numberISO 16366:2008(E)INTERNATIONAL STANDARD ISO16366Second edition2008-03-01Tools for pressing L-shaped guides Ou
5、tillage de presse Glissires de guidage en L BS ISO 16366:2008ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical
6、 committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with
7、 the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Intern
8、ational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may
9、be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16366 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second edition cancels and replaces the first edition (ISO
10、16366:2001), Clause 3 of which has been technically revised. BS ISO 16366:2008blank1Tools for pressing L-shaped guides 1 Scope This International Standard specifies the main dimensions and tolerances of L-shaped guiding bars, to be used in press tools (an application example is shown in Figure 1). I
11、t also specifies the designation of L-shaped guiding bars. Key 1 L-shaped guiding bars 2 sliding plates 3 press tool Figure 1 Application example of L-shaped guiding bars 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer
12、ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 4762, Hexagon socket head
13、cap screws ISO 8733, Parallel pins with internal thread, of unhardened steel and austenitic stainless steel ISO 13715, Technical drawings Edges of undefined shape Vocabulary and indications BS ISO 16366:20082 3 Dimensions The dimensions of L-shaped guiding bars shall conform to the indications in Fi
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO163662008TOOLSFORPRESSINGLSHAPEDGUIDES 冲压 工具 导向 PDF

链接地址:http://www.mydoc123.com/p-585030.html