BS ISO 11529-2013 Milling cutters Designation Shank-type and bore-type milling cutters of solid or tipped design or with indexable cutting edges《铣刀 名称 带可变切削刃的铣刀固体和镶齿产品设计柄类型和钻孔类型》.pdf

《BS ISO 11529-2013 Milling cutters Designation Shank-type and bore-type milling cutters of solid or tipped design or with indexable cutting edges《铣刀 名称 带可变切削刃的铣刀固体和镶齿产品设计柄类型和钻孔类型》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11529-2013 Milling cutters Designation Shank-type and bore-type milling cutters of solid or tipped design or with indexable cutting edges《铣刀 名称 带可变切削刃的铣刀固体和镶齿产品设计柄类型和钻孔类型》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 11529:2013Milling cutters Designation Shank-type and bore-type milling cutters of solidor tipped design or withindexable cutting edgesBS ISO 11529:2013 BRITISH STANDARDNat

2、ional forewordThis British Standard is the UK implementation of ISO 11529:2013. Itsupersedes BS ISO 11529-1:2005 and BS ISO 11529-2:2005 which arewithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of or

3、ganizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 201

4、3ISBN 978 0 580 76122 5ICS 25.100.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 April 2013.Amendments issued since publicationDate T e x t a f f e c t e dBS

5、 ISO 11529:2013 ISO 2013Milling cutters Designation Shank-type and bore-type milling cutters of solid or tipped design or with indexable cutting edgesFraises Dsignation Fraises deux tailles, queue monobloc ou lames ou fraises alsage plaquettes amoviblesINTERNATIONAL STANDARDISO11529First edition2013

6、-05-01Reference numberISO 11529:2013(E)BS ISO 11529:2013ISO 11529:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or

7、 mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749

8、 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 11529:2013ISO 11529:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Summary explanation of the designation system 14 Designation symbols 24.1 Symbol id

9、entifying the diameter Position 1 . 24.2 Symbol identifying the type of milling cutter Position 2 . 24.3 Symbol identifying the number of effective cutting edges 54.4 Symbol identifying the hand of cutting 54.5 Symbol identifying the cutting-edge angle, r.54.6 Symbol identifying the design of end mi

10、ll or milling cutter 54.7 Symbol identifying the maximum cutting depth or width, ap.64.8 Symbol identifying the helix angle or shape of insert . 64.9 Symbol identifying the type (symbol 9) and the style (symbol 10) of shank . 74.10 Symbol identifying the size of shank 105 Manufacturers information 1

11、06 Additional information on cutting part material 11Annex A (informative) Relationship between designations in this International Standard and ISO 13399 (all parts) .12Bibliography .13BS ISO 11529:2013ISO 11529:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide f

12、ederation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that co

13、mmittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accord

14、ance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires

15、 approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 11529 was prepared by Technical Com

16、mittee ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials.The first edition of ISO 11529 cancels and replaces ISO 11529-1:2005 and ISO 11529-2:2005, which have been technically revised.iv ISO 2013 All rights reservedBS ISO 11529:2013INTERNATIONAL STAND

17、ARD ISO 11529:2013(E)Milling cutters Designation Shank-type and bore-type milling cutters of solid or tipped design or with indexable cutting edges1 ScopeThis International Standard establishes a designation system for shank-type and bore-type milling cutters of either solid or tipped design or with

18、 indexable cutting edges with the purpose of simplifying communication between the users and suppliers of such tools.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only t

19、he edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip

20、 breakersISO 3002-3, Basic quantities in cutting and grinding Part 3: Geometric and kinematic quantities in cutting3 Summary explanation of the designation systemShank-type and bore-type milling cutters are designated by codes comprising symbols which identify the important features of the mills.Ext

21、ensions to the designation codes to include manufacturers or suppliers information about the milling cutters are described in Clause 5.No addition to or extension of the designation system given in this International Standard shall be made without consultation with ISO/TC 29 and without its agreemen

22、t. The designation code shall consist of the following:Position Definition of designation symbols1 Number symbol identifying the diameter, (see 4.1)2 Letter symbol identifying the type of milling cutter (see 4.2)3 Number symbol identifying the number of effective cutting edges (see 4.3)4 Letter symb

23、ol identifying the hand of cutting (see 4.4)5 Number symbol identifying the cutting-edge angle, r(see 4.5)6 Letter symbol identifying the design of end mill or milling cutter (see 4.6)7 Number symbol identifying the maximum cutting depth or width, ap(see 4.7)8 Letter symbol identifying the helix ang

24、le or shape of insert (see 4.8)9 Letter symbol identifying the type of shank (see 4.9) ISO 2013 All rights reserved 1BS ISO 11529:2013ISO 11529:2013(E)10 Number symbol identifying the style of shank (see 4.9)11 Number symbol identifying the size of shank (see 4.10)EXAMPLE Position 1 2 3 4 5 6 7 8 9

25、10 11End milling cutter of solid design 32 G 04 R 090 A 012 S ZYL 10 032Milling cutter of indexable design 250 A 12 R 075 S 075 S HSK 01 1004 Designation symbols4.1 Symbol identifying the diameter Position 1The diameter of end mills or milling cutters for each letter symbol is shown in the illustrat

26、ions in Table 1.The number symbol identifying the diameter is a one-digit to three-digit number and corresponds to the diameter, in millimetres.EXAMPLE 1 6 symbol “6”EXAMPLE 2 32 symbol “32”EXAMPLE 3 125 symbol “125”4.2 Symbol identifying the type of milling cutter Position 2Table 1 Type of milling

27、cutterLetter symbolType of milling cutter ShapeAFace mill Square shoulder face mill apHEnd mill side and centre cut-ting (r= 90) Tapered end mill side and cen-tre cutting ap JEnd mill side cutting and ramping (r= 90) Tapered end mill side cutting and ramping ap Table 1 (continued) ISO 2013 All right

28、s reserved 3BS ISO 11529:2013ISO 11529:2013(E)Letter symbolType of milling cutter ShapeKBall-nosed end mill side and centre cutting ap 0,5 LBall-nosed cylindrical end mill side and centre cutting (r= 90) Ball-nosed tapered end mill side and centre cutting ap 0,5 MSpot facing cutter centre cutting =

29、ap= 0,5 not centre cutting = ap 0,5 NToroidal end mill ap PDouble half-side and face mill ap TThread milling cutteraFeed.bSee 4.3.Table 1 (continued)4 ISO 2013 All rights reservedBS ISO 11529:2013ISO 11529:2013(E)4.3 Symbol identifying the number of effective cutting edgesThe number symbol identifyi

30、ng the number of cutting edges is a two-digit number corresponding to the number of effective cutting edges.EXAMPLE 1 12 effective cutting edges: symbol “12”.EXAMPLE 2 2 effective cutting edges: symbol “02”.NOTE The number of effective cutting edges is defined as “the number of cutting edges used to

31、 calculate the feed per tooth in the direction of feed motion from which ris defined”.4.4 Symbol identifying the hand of cuttingThe letter symbol for the hand of cutting for a milling cutter is as shown in Table 2:Table 2 Hand of cuttingLetter symbol Hand of cuttingL Left-handR Right-handN Neutral (

32、both sides)4.5 Symbol identifying the cutting-edge angle, rThe number symbol identifying the cutting edge angle is a three-digit number, corresponding to the nominal cutting edge angle, in degrees, and omitting any decimals. ris defined for the various types of end mill in 4.2, and in ISO 3002-1, 5.

33、1.1.1.The three-digit number designates also milling cutters of “dove tail” design, where the cutting edge angle is larger than 90.EXAMPLE 1 Cutting edge angle 90: symbol “090”.EXAMPLE 2 Dove tail milling cutter with cutting edge angle 120: symbol “120”.For end mills of types K and N (see 4.2), the

34、symbol identifying the cutting edge angle shall be replaced by 000 triple (or treble) zero.If end mills and milling cutters are assembled with cartridges that are carrying the cutting edges, the cutting edge angle shall be replaced by 0CA (zero, upper case letter C, upper case letter A).If ris a dec

35、imal value, the symbol identifying the cutting edge angle shall be replaced by XXX, and the actual value shown as the manufacturers information (see Clause 5).4.6 Symbol identifying the design of end mill or milling cutterThe symbol 6 defines either the design of the end mill or milling cutter, if i

36、t is of solid or tipped design, or the design of how the replaceable cutting edges are fixed on to the tool body.For end mills or milling cutters of solid or tipped design, the letter symbol shall be as shown in Table 3: ISO 2013 All rights reserved 5BS ISO 11529:2013ISO 11529:2013(E)Table 3 Designa

37、tion for solid or tipped designLetter symbol DesignA Solid with plain (continuous) cutting edgesB Solid with interrupted (serrated) cutting edgesD With brazed tips and plain (continuous) cutting edgesE With brazed tips and interrupted (serrated) cutting edgesF With mechanically clamped tips and plai

38、n (continuous) cutting edgesG With mechanically clamped tips and interrupted (serrated) cutting edgesFor end mills or milling cutters with indexable inserts, the letter symbol shall be as shown in Table 4:Table 4 Designation for insert clamping designLetter symbol DesignC Top clampK Milling cutter e

39、quipped with cartridges or cassettesM Top and hole clamp, insert with holeP Hole clamp, insert with holeS Screw clamp, insert with partly cylindrical holeT Tangentially mounted, insert with holeV Tangentially mounted, insert without holeW Wedge clamp, insert without holeX Special features4.7 Symbol

40、identifying the maximum cutting depth or width, apThe number symbol identifying the maximum cutting depth or width, ap(see definition in position 2, and in ISO 3002-3, is a three-digit number. If the value of apis an integer, it is given in millimetres for all types of cutters. If not, apmay be give

41、n as “T”, followed by the value in tenths (1/10) of a millimetre. The latter possibility only applies if apis less than 10 mm.EXAMPLE 1 Maximum cutting depth or width 105 mm: symbol “105”EXAMPLE 2 Maximum cutting depth or width 80 mm: symbol “080”EXAMPLE 3 Maximum cutting depth or width 6 mm: symbol

42、 “006”EXAMPLE 4 Maximum cutting depth or width 7,5 mm: symbol “T75”NOTE apis described in ISO 3002-3 as “back engagement of the cutting edge”.4.8 Symbol identifying the helix angle or shape of insertFor end mills and milling cutters of solid or tipped design (letters “A”, “B”, “D”, “E”, “F”, “G” of

43、symbol 6), the letter symbol shall be as shown in Table 5:6 ISO 2013 All rights reservedBS ISO 11529:2013ISO 11529:2013(E)Table 5 Designation for helix angleNormal helix angle sLetter symbolRight-hand helix Left-hand helix0 A A0 s 5 B M5 s 10 C N10 s 15 D P15 s 20 E Q20 s 25 F S25 s 30 G T30 s 35 H

44、U35 s 45 J V45 s 60 K WOTHERS X YFor end mills and milling cutters with indexable insert design (letters “C”, “K”, “M”, “P”, “S”, “T”, “V”, “W”, “X” of symbol 6), the letter symbol shall be as shown in Table 6:Table 6 Designation for insert shapesLetter symbol Insert shape Insert typeH Hexagonal Equ

45、ilateral and equiangularO OctagonalP PentagonalS SquareT TriangularC Rhombic with 80 included angle Equilateral but non-equiangularD Rhombic with 55 included angleE Rhombic with 75 included angleM Rhombic with 86 included angleV Rhombic with 35 included angleW Trigon with 80 included angleL Rectangu

46、lar Non-equilateral but equiangularA Parallelogram-shaped with 85 included angle Non-equilateral and non-equiangularB Parallelogram-shaped with 82 included angleK Parallelogram-shaped with 55 included angleR Round RoundU Cutters equipped with cartridges or cassettes or nestsX Cutters equipped with o

47、ther shapes of insertsY Cutters equipped with more than one shape of insert4.9 Symbol identifying the type (symbol 9) and the style (symbol 10) of shankSymbol 9 (type of shank or bore) and symbol 10 (style of shank or bore) are according to ISO/TS 13399-60. See Table 7. ISO 2013 All rights reserved

48、7BS ISO 11529:2013ISO 11529:2013(E)Table 7 Designation for shank type and shank styleLetter symbol type of shank or boreaNumber symbol style of shank or borebDescription of shank or bore IllustrationZYL 01 Straight cylindrical shank (ISO 3338-1)ZYL 03 Straight cylindrical shank with attachment threa

49、dZYL 10 Straight cylindrical shank with plain clamping surface Weldon shankZYL 13 Straight cylindrical shank with 2 inclined clamping surface Whistle notch shank without plain contact surfaceZYL 14 Straight cylindrical shank with plain clamping surface and 2 inclined clamping surfaceZYL 17 Straight cylindrical shank with plain clamping surface and attach-ment threadMKG 1x Morse taper shank with attach