BS EN ISO 10772-2012 Geotextiles Test method for the determination of the filtration behaviour of geotextiles under turbulent water flow conditions《土工织物 湍流水流条件下土工织物过滤特性的测定试验方法 n》.pdf

《BS EN ISO 10772-2012 Geotextiles Test method for the determination of the filtration behaviour of geotextiles under turbulent water flow conditions《土工织物 湍流水流条件下土工织物过滤特性的测定试验方法 n》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 10772-2012 Geotextiles Test method for the determination of the filtration behaviour of geotextiles under turbulent water flow conditions《土工织物 湍流水流条件下土工织物过滤特性的测定试验方法 n》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 10772:2012Geotextiles Test methodfor the determination ofthe filtration behaviour ofgeotextiles under turbulentwater flow conditions (ISO10772:2012)Copyright European C

2、ommittee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 10772:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO10772:2012.BSI, as a member of CEN, is o

3、bliged to publish EN ISO 10772:2012as a British Standard. However, attention is drawn to the fact thatduring the development of this European Standard, the UK votedagainst its approval as a European Standard.The reason for the negative vote is the absence of a procedure inClause 6 for determining th

4、e undrained shear strength of the soilto be used in a test. All other parts of the standard meet with theUK approval. The UK committee will be working with CEN TechnicalCommittee 189, Working Group 4, to pursue the possibility of afuture amendment.The UK participation in its preparation was entruste

5、d to TechnicalCommittee B/553, Geotextiles and geomembranes.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The B

6、ritish Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 66615 5ICS 59.080.70Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 Janu

7、ary 2013.Amendments issued since publicationDate T e x t a f f e c t e dCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1

8、0772 August 2012 ICS 59.080.70 English Version Geotextiles - Test method for the determination of the filtration behaviour of geotextiles under turbulent water flow conditions (ISO 10772:2012) Gotextiles - Mthode dessai pour la dtermination du comportement en filtration des gotextiles en rgime dcoul

9、ement turbulent (ISO 10772:2012) Geotextilien - Prfverfahren zur Bestimmung der Filterbestndigkeit von Geotextilien in turbulenten Strmungsbedingungen (ISO 10772:2012) This European Standard was approved by CEN on 14 August 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulati

10、ons which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

11、This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN m

12、embers are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Por

13、tugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by

14、any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10772:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 10772:2012EN ISO 10772:2012 (E) 3 Fo

15、reword This document (EN ISO 10772:2012) has been prepared by Technical Committee ISO/TC 221 “Geosynthetics“ in collaboration with Technical Committee CEN/TC 189 “Geosynthetics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either b

16、y publication of an identical text or by endorsement, at the latest by February 2013, and conflicting national standards shall be withdrawn at the latest by February 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or

17、 CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech R

18、epublic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. E

19、ndorsement notice The text of ISO 10772:2012 has been approved by CEN as a EN ISO 10772:2012 without any modification. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1

20、0772:2012ISO 10772:2012(E) ISO 2012 All rights reserved iiiContents PageForeword iv1 Scope 12 Normative references . 13 Terms and definitions . 14 Principles . 15 Test method 16 Test soils 27 Sampling and sample installation . 28 Test apparatus 29 Procedure 310 Evaluation 311 Test report . 4Annex A

21、(informative) Grading curve 9Bibliography .10Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 10772:2012ISO 10772:2012(E)ForewordISO (the International Organization for

22、Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the r

23、ight to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.Internationa

24、l Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as a

25、n International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 10

26、772 was prepared by Technical Committee ISO/TC 221, Geosynthetics.iv ISO 2012 All rights reservedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 10772:2012INTERNATIONAL

27、 STANDARD ISO 10772:2012(E)Geotextiles Test method for the determination of the filtration behaviour of geotextiles under turbulent water flow conditions1 ScopeThis International Standard describes a test method for determining the soil passing through a geotextile filter when exposed to turbulent e

28、xternal water flow conditions.The test provides a value for one specific type of soil as a performance test for the design of erosion protection layers with geotextile filters in hydraulic engineering applications.2 Normative referencesThe following referenced documents are indispensable for the app

29、lication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 9862, Geosynthetics Sampling and preparation of test specimensISO 12956, Geotextiles and geotextile-related pr

30、oducts Determination of the characteristic opening size3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply:3.1soil passing valueSpvcumulative average soil passing value for the three specimens after the final stage3.2cohesioncuundrained cohesion of the

31、 test soil3.3plasticity indexIPplasticity of test soil4 PrinciplesThe test simulates the exposure of geotextiles to turbulent conditions such as those that occur during wave action, the passage of a ship, etc. The filtration stability of the geotextile is determined by measuring the amount and rate

32、of soil passing through the geotextile during the test.5 Test methodThe mechanical filtration stability of the test soil and of similar soils is determined by measuring the soil passing through the filter during each stage of the test. The test results will also show whether the rate at which soil p

33、asses through the geotextile filter has been stabilized as necessary. ISO 2012 All rights reserved 1Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 10772:2012ISO 10772:

34、2012(E)6 Test soilsThe test soil is dried to constant mass at 105C directly before use.An example for the grading curve of a medium to coarse silt as test soil is shown in Annex A. The cohesion of the undrained test soil is less than or equal to 1,5 kN/m2.7 Sampling and sample installationThe sampli

35、ng shall be carried out in accordance with ISO 9862. Three geotextile specimens, each with a diameter of 168 mm, are punched out of the laboratory sample. Each specimen shall be placed in a sample container with the upper surface of the geotextile facing downwards as shown in Figure 1. 1 500 g of th

36、e test soil type are placed loosely on the geotextile and spread evenly over the sample using an adjustable gauge. Compact the test soil by using a pressure that exerts a surface pressure of 2 kN/m2on the geotextile. The load is applied using 1 500 g of the test soil and a 151 mm diameter brass disc

37、 weighing 2 130 g. Two pieces of non-woven geotextile material (mass per unit area: 600 g/m2, thickness: 6 mm) with diameters of 152 mm shall be placed between the upper surface of the test soil and the metal disc to prevent any loss of soil at the annular gap between the sample mould and the disc.F

38、asten the specimen container securely on a vertically oscillating electromagnetic screen (e.g. sieving device according to ISO 12956) for compaction. Place a 5 mm thick plastic disc beneath the geotextile specimen to prevent the material from sagging while the soil is being compacted. The soil shall

39、 be compacted at a frequency of 50 Hz and an amplitude of 1,5 mm for 240 s. The lid of the test specimen is then closed and the specimen stored in tap water at a temperature of 20C 5C and left to saturate for at least 16 h. Cover the test specimen with water to a depth of 20 cm. Immerse the specimen

40、 at an angle such as to prevent any air bubbles being trapped under the surface of the geotextile.8 Test apparatusThe test apparatus shall be designed to test with three sample containers simultaneously. It comprises a load-bearing steel frame with a flange-mounted electric motor (the drive), an ele

41、ctric control system, a v-belt drive, drive shafts fitted with turbulence-producing fans, sample containers and collecting vessels. The dimensions of the test apparatus are shown in Figures 2a), 2b) and 3. The materials, dimensions and structure of the single sample containers are shown in Figures 1

42、a) and 1b). The sample containers are fastened firmly to the test frame by means of the brass pipe bolted in the centre of the transparent plastic lid. The pipe is also used to evacuate air from the sample containers and equalize the pressure inside them during the test. The water level in the water

43、 tank at rest is set using the millimetre scale on the transparent plastic window at the front of the tank. The rotor speed depends on the fixed v-belt pulley ratios. A reliable means of measuring the speed will be required if a variable-speed motor is used.The four-bladed turbulence-producing agita

44、tor rotating at 260 rpm produces a turbulent flow that hits the filter sample at speeds between 70 cm/s and 90 cm/s. The passage of the blades beneath the geotextile sample produces pressure pulsations with a frequency of 17,3 Hz.The following are also necessary to carry out the determination of the

45、 filtration behaviour of geotextiles under turbulent water flow conditions:8.1 Drying oven, capable of maintaining a temperature of 105C 5C.8.2 Electronic balance (the resolution must be 0,01 g).8.3 Tap water.8.4 Vertically oscillating device, as described in ISO 12956.8.5 Vessels for the water coll

46、ection, with a volume greater than 60 l.2 ISO 2012 All rights reservedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 10772:2012ISO 10772:2012(E)8.6 Hydrophilic cellulo

47、se folded filter, with a diameter of 500 mm and a retention range of 5 m to 13 m.8.7 Stainless steel mesh, mesh size 11 mm, wire size 1 mm.8.8 Spacer, with the dimensions 30 mm 30 mm 90 mm, made of plastic or wood.9 ProcedureThe test procedure includes five loading phases each lasting 30 min with a

48、total duration of 150 min for each geotextile specimen. For each load phase, the following procedure should be used:9.1 Measure the water temperature in the test container at the beginning and end of the test, which shall be in the range 20C 5C.9.2 Fill the test container with water up to a height o

49、f 20,5 cm.9.3 Remove the specimen container from the water in which it has been stored and place it in the test container immediately, immersing it at an angle to prevent any air bubbles forming beneath the test surface.9.4 Adjust the height of the specimen container by placing a spacer with a height of