BS EN ISO 3964-2016 Dentistry Coupling dimensions for handpiece connectors《牙科 手机连接器连接尺寸》.pdf

《BS EN ISO 3964-2016 Dentistry Coupling dimensions for handpiece connectors《牙科 手机连接器连接尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 3964-2016 Dentistry Coupling dimensions for handpiece connectors《牙科 手机连接器连接尺寸》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO 3964:2016Dentistry Couplingdimensions for handpiececonnectors (ISO 3964:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 3964:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 3964:2016. It supersed

2、es BS 7077-2.2:1989 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee CH/106/4, Dental Instruments and Equipment.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to includ

3、e all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 85771 3 ICS 11.060.20; 11.060.25 Compliance with a British Standard cannot confer immunity from legal obligat

4、ions.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 3964 November 2016 ICS 11.060.25 Supersedes EN 2396

5、4:1989English Version Dentistry - Coupling dimensions for handpiece connectors (ISO 3964:2016) Mdecine bucco-dentaire - Dimensions daccouplement pour pices main dentaires (ISO 3964:2016) Zahnheilkunde - Kupplungsmae fr Handstckverbindungen (ISO 3964:2016) This European Standard was approved by CEN o

6、n 7 August 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may

7、 be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified t

8、o the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland,

9、 Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Managemen

10、t Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 3964:2016 EBS EN ISO 3964:2016EN ISO 3964:2016 (E) 3 European foreword This document (EN ISO 3964:2016) has been prepared by Techn

11、ical Committee ISO/TC 106 “Dentistry” in collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2

12、017, and conflicting national standards shall be withdrawn at the latest by May 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.

13、This document supersedes EN 23964:1989. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yug

14、oslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 3964:2016 ha

15、s been approved by CEN as EN ISO 3964:2016 without any modification. BS EN ISO 3964:2016ISO 3964:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Classification 15 Requirements 25.1 General . 25.2 Dimensions . 25.3 Coupling force . 106 Sampling .107 Test methods 107.

16、1 Dimensions 107.2 Coupling force . 11 ISO 2016 All rights reserved iiiContents PageBS EN ISO 3964:2016ISO 3964:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Stan

17、dards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also t

18、ake part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In p

19、articular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements o

20、f this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see

21、 www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to

22、 the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee responsible for this document is ISO/TC 106 Dentistry, Subcommittee SC 4 Dental instruments.This third edition cancels and replaces the second edition (ISO 3964:1982

23、), which has been technically revised with the following changes:a) addition of definitions for “coupling dimension” and “coupling systems”;b) addition of four types for “classification”;c) additional types of coupling systems: with and without light supply; with internal and external supply of air

24、and water (spray);d) improved technical drawings.iv ISO 2016 All rights reservedBS EN ISO 3964:2016INTERNATIONAL STANDARD ISO 3964:2016(E)Dentistry Coupling dimensions for handpiece connectors1 ScopeThis International Standard specifies the coupling between handpieces and motors connected to dental

25、units.This International Standard specifies the nominal dimensions, tolerances and the extraction force of coupling systems for use between handpiece and motor which supply the handpiece with water, air and light and rotation energy.2 Normative referencesThe following documents, in whole or in part,

26、 are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1942, Dentistry VocabularyISO 2768-1, General tol

27、erances Part 1: Tolerances for linear and angular dimensions without individual tolerance indicationsISO 2768-2, General tolerances Part 2: Geometrical tolerances for features without individual tolerance indicationsISO 14457, Dentistry Handpieces and motors3 Terms and definitionsFor the purposes of

28、 this document, the terms and definitions given in ISO 1942, ISO 14457 and the following apply.3.1coupling dimensiondescription of the dimensions of connectors between air- and electrical motors and straight and angled handpieces, used to connect and supply the handpiece system3.2coupling systemcomb

29、ination of connector parts between air- and electrical motors and straight and angled handpieces, used to connect and supply the handpiece system4 ClassificationFor the purpose of this International Standard, coupling systems are classified into the following types: Type 1: coupling system for strai

30、ght and angle handpieces and motors without internal spray supply and without light supply; Type 2: coupling system for straight and angle handpieces and motors with internal spray supply and without light supply; ISO 2016 All rights reserved 1BS EN ISO 3964:2016ISO 3964:2016(E) Type 3: coupling sys

31、tem for straight and angle handpieces and motors with internal spray supply and with light supply; Type 4: coupling system for straight and angle handpieces and motors without internal spray supply and with light supply.5 Requirements5.1 GeneralTypes of the coupling for handpieces and for motors are

32、 specific parts of dental handpieces.Requirements for dental handpieces are specified in ISO 14457.5.2 DimensionsThe dimensions and the configuration of handpiece-sides and motor-sides shall be as specified in Figure 1, Figure 2, Figure 3, Figure 4, Figure 5, Figure 6, Figure 7 and Figure 8 with cou

33、pling dimensions X1and X2as specified in Table 1.Table 1 Coupling dimensions X1and X2Coupling Dimension Long Middle Short Extra shortMotor X1max. 31,8 mm max. 24,8 mm max. 22,8 mm max. 18,8 mmHandpiece X2min. 32 mm min. 25 mm min. 23 mm min. 19 mmDimensions without tolerances shall be in accordance

34、with ISO 2768-1 and ISO 2768-2.Alternative designs of the coupling lock system are permitted.The type of handpiece length shall be indicated in the manufacturers instructions for use.Testing shall be carried out in accordance with 7.1.2 ISO 2016 All rights reservedBS EN ISO 3964:2016ISO 3964:2016(E)

35、Dimensions in millimetresEdges shall be burr-free or round.Figure 1 Type 1 Handpiece ISO 2016 All rights reserved 3BS EN ISO 3964:2016ISO 3964:2016(E)Dimensions in millimetresKeyr can either be a radius or a cone shape with the point angle of 120Edges shall be burr-free or round.Figure 2 Type 1 Moto

36、r4 ISO 2016 All rights reservedBS EN ISO 3964:2016ISO 3964:2016(E)Dimensions in millimetresKey1 air2 water3 grooves and geometry for sealing rings given by the manufacturer4 - - - - - sealing surfaceEdges shall be burr-free or round.Figure 3 Type 2 Handpiece ISO 2016 All rights reserved 5BS EN ISO 3

37、964:2016ISO 3964:2016(E)Dimensions in millimetresKey1 sealing ringr can either be a radius or a cone shape with the point angle of 120Edges shall be burr-free or round.aLocking device, as given by the manufacturer.bAxial clearance with connected handpiece max. 0,3 mm.cGrooves and geometry for sealin

38、g rings given by the manufacturer.dWater.eAir.Figure 4 Type 2 Motor6 ISO 2016 All rights reservedBS EN ISO 3964:2016ISO 3964:2016(E)Dimensions in millimetresKey1 air2 water3 grooves and geometry for sealing rings given by the manufacturer4 light entrance5 - - - - - - sealing surfaceEdges shall be bu

39、rr-free or round.Figure 5 Type 3 Handpiece ISO 2016 All rights reserved 7BS EN ISO 3964:2016ISO 3964:2016(E)Dimensions in millimetresKey1 handpiece, connected2 light exit3 sealing ringr can either be a radius or a cone shape with the point angle of 120Edges shall be burr-free or round.aLocking devic

40、e, as given by the manufacturer.bAxial clearance with connected handpiece max. 0,3 mm.cGroves and geometry of sealing rings given by the manufacturer.dWater.eAir.Figure 6 Type 3 Motor8 ISO 2016 All rights reservedBS EN ISO 3964:2016ISO 3964:2016(E)Dimensions in millimetresKey1 grooves and geometry f

41、or sealing rings given by the manufacturer2 light entrance3 - - - - - - sealing surfaceEdges shall be burr-free or round.Figure 7 Type 4 Handpiece ISO 2016 All rights reserved 9BS EN ISO 3964:2016ISO 3964:2016(E)Dimensions in millimetresKey1 handpiece, connected2 light exitr can either be a radius o

42、r a cone shape with the point angle of 120Edges shall be burr-free or round.aLocking device, as given by the manufacturer.bAxial clearance with connected handpiece max. 0,3 mm.Figure 8 Type 4 Motor5.3 Coupling forceThe extraction force required to move the connected handpiece from the motor shall be

43、 at least 30 N or the motor shall have an appropriate design to release cooling air pressure.Testing shall be carried out in accordance with 7.2.6 SamplingOne representative sample of each type of coupling system shall be selected for the test.7 Test methods7.1 DimensionsUse a measuring device with

44、an accuracy of 0,01 mm for linear dimensions or 1 for angles, e.g. a gauge or dial indicator. Measure and record the dimensions shown in Figure 1, Figure 2, Figure 3, Figure 4, Figure 5, Figure 6, Figure 7 and Figure 8.10 ISO 2016 All rights reservedBS EN ISO 3964:2016ISO 3964:2016(E)7.2 Coupling fo

45、rceInstall the handpiece with the motor in accordance with the manufacturers instructions. Use a measuring device such as a spring force gauge with an accuracy of 0,5 N. Measure and record the extraction forces required to disconnect the coupling system. ISO 2016 All rights reserved 11This page deli

46、berately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI

47、Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a d

48、ependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British S

49、tandards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered fr