BS EN 61300-2-45-1999 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Tests - Durability test by water immersion《光纤互联装置和无源部件 基本.pdf

《BS EN 61300-2-45-1999 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Tests - Durability test by water immersion《光纤互联装置和无源部件 基本.pdf》由会员分享，可在线阅读，更多相关《BS EN 61300-2-45-1999 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Tests - Durability test by water immersion《光纤互联装置和无源部件 基本.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61300-2-45: 1999 IEC 61300-2-45: 1999 Fibre optic interconnecting devices and passive componentsBasic test and measurement procedures Part2-45: Tests Durability test by water immersion The European Standard EN61300-2-45:1999 has the status of a BritishStandard ICS 33.180.20BSE

2、N61300-2-45:1999 This BritishStandard, having been prepared under the directionof the Electrotechnical Sector Committee, was publishedunder the authority ofthe Standards Committeeandcomes into effect on 15October1999 BSI 02-2000 ISBN 0 580 35219 6 National foreword This BritishStandard is the Englis

3、h language version of EN61300-2-45:1999. It is identical with IEC61300-2-45:1999. The UK participation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Interconnecting devices and passive components, which has the responsibility to: aid enquirer

4、s to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations repre

5、sented on this subcommittee can be obtained on request to its secretary. From1January1997, all IEC publications have the number60000 added to the old number. For instance, IEC27-1 has been renumbered as IEC60027-1. For a period of time during the change over from one numbering system to the other, p

6、ublications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The BritishStandards which im

7、plement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all th

8、e necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, t

9、heEN title page, pages2 to4 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN61300-2-45:1999 BSI 02-20

10、00 i Contents Page National foreword Inside front cover Foreword 2 Text of EN61300-2-45 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN61300-2-45 August1999 ICS33.180.20 English version Fibre optic interconnecting devices and passive components Basic test and measurement procedures Par

11、t2-45: Tests Durability test by water immersion (IEC61300-2-45:1999) Dispositifs dinterconnexion et composants passifs fibres optiques Mthodes fondamentales dessais et de mesures Partie2-45: Essais Essai de durabilit par immersion dans leau (CEI61300-2-45:1999) Lichtwellenleiter Verbindungselemente

12、und passive Bauteile Grundlegende Prf- und Meverfahren Teil2-45: Prfungen Bestndigkeit gegen Eintauchen in Wasser (IEC61300-2-45:1999) This European Standard was approved by CENELEC on1999-08-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condit

13、ions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in thr

14、ee official versions(English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnica

15、l committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisatio

16、n Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1999 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref.No.EN61300-2-45:1999EEN61300-2-45:1999 BSI 02-2000 2 Foreword

17、The text of document86B/1188/FDIS, future edition1 of IEC61300-2-45, prepared by SC86B, Fibre optic interconnecting devices and passive components, of IEC TC86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN61300-2-45 on1999-08-01. The following dates

18、were fixed: Endorsement notice The text of the International Standard IEC61300-2-45:1999 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1 General 3 1.1 Scope and object 3 1.2 General description 3 2 Apparatus 3 2.1 Containers 3 2.2 Water 3 2.3 Heat

19、source 3 2.4 Oven 3 3 Procedure 3 4 Severity 4 5 Details to be specified 4 latest date by which the ENhas to be implemented at national level by publication of an identical national standard or by endorsement (dop)2000-05-01 latest date by which the national standards conflicting with the EN haveto

20、be withdrawn (dow)2002-08-01EN61300-2-45:1999 BSI 02-2000 3 1 General 1.1 Scope and object The purpose of this part of IEC61300 is to establish the ability of a fibre optic component to resist degradation when exposed to water immersion which the component may experience during its service life. 1.2

21、 General description The specimen is immersed in water for a specified period of time. 2 Apparatus The apparatus consists of the following elements. 2.1 Containers A boro-silicate glass or stainless steel vessel of suitable volume for the water shall be used. Vessels shall be of sufficient size and

22、capacity to permit the specimen to be appropriately immersed in water without violating other physical constraints (e.g.the minimum cable bend radius). 2.2 Water Distilled water. 2.3 Heat source A suitable heat source capable of achieving and maintaining the specified temperature within 2 C of there

23、quired setting. 2.4 Oven A suitable oven to dry the specimen during repeated immersion testing. 3 Procedure The preparation of the specimen shall be in accordance with the relevant specification. Perform any pre-test measurements specified in the relevant specification. Unless otherwise specified, t

24、he specimen shall be subjected to the test in a non-operational mode. 3.1 Precondition the specimen and the water as specified in the relevant specification. 3.2 Prepare a vessel with sufficient water such that the specimen can be adequately immersed. The quantity of water shall be sufficient such t

25、hat the device under test is1cm to5cm below the surface of the water. 3.3 Immerse the specimen for the specified period while maintaining the water temperature. The specimen shall be immersed during the test. 3.4 At the end of the specified period, remove the specimen from the bath. 3.5 The surplus

26、water shall be wiped off and the specimen shall be allowed to dry at room temperature for24h without controlling its humidity following the removal from the immersion bath. 3.6 When the repeated immersion test is carried out, the surplus water shall be wiped off and the specimen placed in the oven t

27、o dry for2h at40 C. Before the next immersion, the specimen shall be allowed to stabilise at room temperature for2h. This procedure shall be repeated following subsequent immersions. 3.7 Upon completion of the test, the specimen(s) shall be examined and all necessary observations recorded as specifi

28、ed in the relevant specification. Special attention shall be paid to swelling of materials, loss of adhesive bonding between bonded surfaces, corrosion of materials, softening of materials, degradation of optical characteristics, etc.EN61300-2-45:1999 4 BSI 02-2000 4 Severity The severity consists o

29、f a combination of the following: water temperature, period of immersion, number of cycles of immersion and depth of immersion. The severity shall be specified in the relevant specification. The following severities, which are not mandatory, may be specified for this procedure. 5 Details to be speci

30、fied The following details, as applicable, shall be specified in the relevant specification: specimen optically functioning or non-functioning; pre-conditioning procedure; water temperature; depth of immersion; immersion period; recovery procedure; initial examination and measurements and performanc

31、e requirements; final examination and measurements and performance requirements; number of immersion cycles; deviations from test procedure; additional pass/fail criteria. Water temperature( 2 C) C Period of immersion Cycles of immersion 5 25 45 10min 1h 24h 168h 1 3 7 30blankBS EN 61300-2-45: 1999

32、IEC 61300-2-45: 1999 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions

33、BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity

34、while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatical

35、ly receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI impleme

36、ntation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic infor

37、mation services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. F

38、or details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Co

39、pyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing t

40、he standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.