BS EN 61300-2-42-2014 Fibre optic interconnecting devices and passive components Basic test and measurement procedures Tests Static side load for strain relief《光纤互连器件和无源元件 基本试验和测量程.pdf

《BS EN 61300-2-42-2014 Fibre optic interconnecting devices and passive components Basic test and measurement procedures Tests Static side load for strain relief《光纤互连器件和无源元件 基本试验和测量程.pdf》由会员分享，可在线阅读，更多相关《BS EN 61300-2-42-2014 Fibre optic interconnecting devices and passive components Basic test and measurement procedures Tests Static side load for strain relief《光纤互连器件和无源元件 基本试验和测量程.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationFibre optic interconnecting devices and passive components Basic test and measurement proceduresPart 2-42: Tests Static side load for strain reliefBS EN 61300-2-42:2014National forewordThis British Standard is the UK implementation of EN 61300-2-42:2014. It isidentical to IE

2、C 61300-2-42:2014. It supersedes BS EN 61300-2-42:2005which is withdrawn.The UK participation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre opticinterconnecting devices and passive components.A list of organizations represented on this c

3、ommittee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 78246 6ICS 33.18

4、0.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2014.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61300-2-42:2

5、014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61300-2-42 May 2014 ICS 33.180.20 Supersedes EN 61300-2-42:2005 English Version Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-42: Tests - Static side load for strain relief (IEC 6130

6、0-2-42:2014) Dispositifs dinterconnexion et composants passifs fibres optiques - Procdures fondamentales dessais et de mesures - Partie 2-42: Essais - Charge latrale statique pour serre-cble (CEI 61300-2-42:2014) Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prf- und Me

7、ssverfahren Teil 2-42: Prfungen - Statische Seitenlast fr die Zugentlastung (IEC 61300-2-42:2014) This European Standard was approved by CENELEC on 2014-03-13. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standa

8、rd the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (Engl

9、ish, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of

10、 Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

11、 Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All right

12、s of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61300-2-42:2014 E BS EN 61300-2-42:2014EN 61300-2-42:2014 - 2 - Foreword The text of document 86B/3699/FDIS, future edition 3 of IEC 61300-2-42, prepared by SC 86B “Fibre optic interconnecting devices

13、and passive components“ of IEC/TC 86 “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-42:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard

14、or by endorsement (dop) 2014-12-13 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-03-13 This document supersedes EN 61300-2-42:2005. EN 61300-2-42:2014 includes the following significant technical changes with respect to EN 61300-2-42:2005:

15、modification of the severity according to cable configurations. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The

16、 text of the International Standard IEC 61300-2-42:2014 was approved by CENELEC as a European Standard without any modification. BS EN 61300-2-42:2014- 3 - EN 61300-2-42:2014 Annex ZA (normative) Normative references to international publications with their corresponding European publications The fo

17、llowing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When a

18、n International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 61300-1

19、- Fibre optic interconnecting devices and passive components - Basic test and measurement procedures Part 1: General and guidance EN 61300-1 - IEC 61300-3-1 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures Part 3-1: Examinations and measurements -

20、Visual examination EN 61300-3-1 - IEC 61300-3-3 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures Part 3-3: Examinations and measurements - Active monitoring of changes in attenuation and return loss EN 61300-3-3 - IEC 61300-3-4 - Fibre optic interc

21、onnecting devices and passive components - Basic test and measurement procedures Part 3-4: Examinations and measurements - Attenuation EN 61300-3-4 - BS EN 61300-2-42:2014 2 61300-2-42 IEC:2014 CONTENTS 1 Scope . 5 2 Normative references 5 3 General description . 5 4 Apparatus . 5 4.1 Load generator

22、 5 4.2 Holding fixture . 6 4.3 Optical source and detector . 6 5 Procedure . 6 5.1 Preparation of specimens 6 5.2 Pre-conditioning 6 5.3 Initial measurements . 6 5.4 Conditioning 6 5.5 Measure the attenuation 7 5.6 Apply cable load 7 5.7 Monitor attenuation 7 5.8 Recovery . 7 5.9 Final measurements

23、and examinations 8 5.10 Repeated testing . 8 6 Severity 8 7 Details to be specified . 9 Figure 1 Test apparatus for static side load 7 Table 1 Severities 8 BS EN 61300-2-42:201461300-2-42 IEC:2014 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part

24、 2-42: Tests Static side load for strain relief 1 Scope This part of IEC 61300 specifies a test to determine the influence of a side load applied to a cord assembled with a strain relief. The intention is to simulate a static load, due to a length of fibre cable, which would typically be experienced

25、 during service. Components should withstand side loads during optical transmission without degradation of the optical performance. Besides a boot, any feature that controls the bending radius of the fibre can be considered as strain relief. 2 Normative references The following documents, in whole o

26、r in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-1, Fibre optic interconnecting d

27、evices and passive components Basic test and measurement procedures Part 1: General and guidance IEC 61300-3-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination IEC 61300-3-3, Fibre optic inter

28、connecting devices and passive components Basic test and measurement procedures Part 3-3: Examinations and measurements Active monitoring of changes in attenuation and return loss IEC 61300-3-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-4

29、: Examinations and measurements Attenuation 3 General description The specimen is inserted into the test apparatus as shown in Figure 1. A load, equivalent to several metres of cable, is applied to the cable attached to the device under test and any changes in optical attenuation are recorded during

30、 the specified period of the test. NOTE This test is applicable only to those passive optical components where the product design incorporates fibre cable pigtails. 4 Apparatus 4.1 Load generator The load generator consists of a mass and a means of clamping the mass to the cable. The clamping shall

31、not introduce micro- or macro-bending losses in the cable. BS EN 61300-2-42:2014 6 61300-2-42 IEC:2014 4.2 Holding fixture The holding fixture consists of a means to hold the device under test in a stable and representative manner. For connectors, the holding fixture shall incorporate an adaptor whe

32、re required. The holding fixture shall be capable of accommodating those devices where the input and output fibre cables are co-located on the same side of the device. 4.3 Optical source and detector The optical source and detector used to measure changes in attenuation shall comply with that specif

33、ied in IEC 61300-3-4. A device to record attenuation over time (X, t) should be used where the optical detector does not have the capability to monitor continuously (i.e. where the sample rate is 10/min). 5 Procedure 5.1 Preparation of specimens Prepare the specimens according to the manufacturers i

34、nstructions or as specified in the relevant specification. The device under test shall be terminated with a sufficient length of fibre cable to facilitate interfacing with the optical source and detector. 5.2 Pre-conditioning Pre-condition the device under test for 2 h at the standard test condition

35、s as given in IEC 61300-1, unless otherwise specified in the relevant specification. 5.3 Initial measurements Complete initial examinations and measurements on the specimen as required by the relevant specification. Measure and record the attenuation of the device under test. 5.4 Conditioning The bo

36、dy of the specimen shall be mounted in a representative manner onto the holding fixture (see Figure 1). The clamp to which the load can be applied shall be fastened to the cable in such a manner that the optical fibre or cable is not crushed. Unless otherwise specified, the point of load application

37、 shall be 20 cm to 30 cm from the end of the strain relief. BS EN 61300-2-42:201461300-2-42 IEC:2014 7 Cable Strain relief To optical source Clamping device Load generator Device under test To detector Holding fixture Weights 20cm-30 cmIEC 0021/14 Figure 1 Test apparatus for static side load 5.5 Mea

38、sure the attenuation Re-measure the attenuation to ensure that the fixturing and cable clamping have not affected the cables attenuation. 5.6 Apply cable load Gradually apply the specified load to the cable clamping fixture, being careful to avoid any sudden jerking or straining of the cable. Mainta

39、in the load for recommended duration (or as specified in the relevant specification). 5.7 Monitor attenuation The attenuation of the specimen shall be continuously monitored during the test, as described in IEC 61300-3-3, unless otherwise specified in the relevant specification. Any deviation in the

40、 device attenuation from that measured in 5.5 shall be considered attributable to the cable/device interface, or fibre-to-fibre interfaces in the device. If there are unacceptable changes in attenuation and it is questionable whether the cable itself may be at fault, a control test to determine cabl

41、e contribution should be performed in the same manner using a piece of cable and two cable clamps. 5.8 Recovery Allow the specimen to remain under standard test conditions for 2 h at the standard test conditions as given in IEC 61300-1, unless otherwise specified in the relevant specification. BS EN

42、 61300-2-42:2014 8 61300-2-42 IEC:2014 5.9 Final measurements and examinations On completion of the specified duration, remove all fixtures and make a final attenuation measurement to ensure that there is no permanent damage to the device under test. The results of the final measurement shall be wit

43、hin the limit established in the relevant specification. Remove the device from the mounting fixture and, unless otherwise specified, visually examine the specimen in accordance with IEC 61300-3-1. Check for evidence of any degradation in the specimen. This may include, for example: broken, loose or

44、 damaged parts or accessories; breaking or damage to the cable jacket, seals, strain relief, or fibres; displaced, bent, or broken parts. 5.10 Repeated testing Where required by the relevant specification, the test shall be repeated with the load applied in mutually perpendicular directions as permi

45、tted by the product design. For example, a product with a base plate extending beyond the fibre exit may prohibit loading in that direction. The number of mutually perpendicular directions employed shall be defined. 6 Severity The severity of the test is dependent upon the tensile load applied and t

46、he duration, as recommended in Table 1. Table 1 Severities Category Component type Load N Duration min C, U and E Connectors and passive components Reinforced cable 1,0 0,1 60 C, U and E Connectors and passive components Secondary coated fibres 0,2 0,02 5 C and U Fibre management systems Reinforced

47、cables 1,0 0,1 60 C and U Fibre management systems Cable elements 0,5 0,1 5 O Passive components Reinforced cables 5,0 0,5 5 O Passive components Primary and secondary coated fibres 2,3 0,2 5 BS EN 61300-2-42:201461300-2-42 IEC:2014 9 7 Details to be specified The following details, as applicable, s

48、hall be specified in the relevant specification: magnitude of the load applied to the cable; duration of the load application; cable configuration; number of mutually perpendicular directions of load application; initial examinations, measurements and performance requirements; examinations and measu

49、rements during test and performance requirements; final examinations, measurements and performance requirements; deviations from this test method; additional pass/fail criteria; wavelength of the source. _ BS EN 61300-2-42:2014This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, inform