BS EN 61047-2004 D C or A C supplied electronic step-down convertors for filament lamps - Performance requirements《钨丝灯用交直流供电电子降压转换器 性能要求》.pdf

《BS EN 61047-2004 D C or A C supplied electronic step-down convertors for filament lamps - Performance requirements《钨丝灯用交直流供电电子降压转换器 性能要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61047-2004 D C or A C supplied electronic step-down convertors for filament lamps - Performance requirements《钨丝灯用交直流供电电子降压转换器 性能要求》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61047:2004 DC or AC supplied electronic step-down convertors for filament lamps Performance requirements The European Standard EN 61047:2004 has the status of a British Standard ICS 29.140.20 BS EN 61047:2004 This British Standard was published under the authority of the Stand

2、ards Policy and Strategy Committee on 15 November 2004 BSI 15 November 2004 ISBN 0 580 44742 1 National foreword This British Standard is the official English language version of EN 61047:2004. It is identical with IEC 61047:2004. It supersedes BS EN 61047:1993, which is withdrawn. The UK participat

3、ion in its preparation was entrusted by Technical Committee CPL/34, Lamps and related equipment, to Subcommittee CPL/34/3, Auxiliaries for lamps, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Th

4、e British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standar

5、ds Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the re

6、sponsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front

7、cover, the EN title page, pages 2 to 16, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 61047 NORME EUROPENNE EUROPISCHE NORM Octobe

8、r 2004 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2004 CENELEC - All rights of exploitation in any form and by any means re

9、served worldwide for CENELEC members. Ref. No. EN 61047:2004 E ICS 29.140.20 Supersedes EN 61047:1992 + A1:1996 + A2:2001English version DC or AC supplied electronic step-down convertors for filament lamps - Performance requirements (IEC 61047:2004) Convertisseurs abaisseurs lectroniques aliments en

10、 courant continu ou alternatif pour lampes incandescence Exigences de performance (CEI 61047:2004) Gleich- oder wechselstromversorgte elektronische Konverter fr Glhlampen - Anforderungen an die Arbeitsweise (IEC 61047:2004) This European Standard was approved by CENELEC on 2004-09-01. CENELEC member

11、s are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application

12、 to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has

13、 the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland

14、, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Foreword The text of document 34C/635/FDIS, future edition 2 of IEC 61047, prepared by SC 34C, Auxiliaries for lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote and was appro

15、ved by CENELEC as EN 61047 on 2004-09-01. This European Standard supersedes EN 61047:1992 + A1:1996 + A2:2001. It constitutes a technical revision. EN 61047:1992 needed to be revised completely after the decision to delete all EMC-related requirements, given that EMC varies from region to region. Th

16、is European Standard is to be read in conjunction with EN 61347-1 and EN 61347-2-2. In this standard, the following print types are used: requirements proper: in roman type; test specifications: in italic type; notes: in smaller roman type. The following dates were fixed: latest date by which the EN

17、 has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2005-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-09-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of

18、the International Standard IEC 61047:2004 was approved by CENELEC as a European Standard without any modification. _ Page2 EN61047:2004 3 CONTENTS Introduction.4 1 Scope.5 2 Normative references .5 3 Terms and definitions .5 4 General notes on tests .6 5 Classification7 5.1 Classification according

19、to the load .7 5.2 Classification according to output voltage7 6 Marking 7 6.1 Mandatory marking7 6.2 Optional marking .7 7 Output voltage and current .8 7.1 Open-circuit voltage 8 7.2 Voltage during operation .8 7.3 Voltage surges during switching and operation8 7.4 Voltage waveform8 7.5 Inrush cur

20、rent8 8 Total circuit power 8 9 Circuit power factor 9 10 Supply current 9 11 Impedance at audio-frequencies.9 12 Operational tests for abnormal conditions.9 13 Endurance10 Annex A (normative) Tests11 Annex B (informative) A guide to quoting product life and failure rate .14 Figure A.1 Measurement o

21、f currents 12 Figure A.2 Measurement of impedance at audio-frequencies .13 Page3 EN61047:2004 3INTRODUCTION This International Standard covers performance requirements for electronic step-down convertors for d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, operating with

22、controlled voltage filament lamps at frequencies deviating from the supply frequency. Attention is drawn to the fact that operating frequencies below 20 kHz may cause audio noise. NOTE CISPR requirements regarding radio interference have to be observed in some countries. In order to obtain satisfact

23、ory performance of filament lamps and electronic convertors, it is necessary that certain features of their designs be properly coordinated. Page4 EN61047:2004 4DC OR AC SUPPLIED ELECTRONIC STEP-DOWN CONVERTORS FOR FILAMENT LAMPS PERFORMANCE REQUIREMENTS 1 Scope This International Standard specifies

24、 performance requirements for electronic step-down convertors for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with tungsten halogen lamps as specified in IEC 60357 and other filament lam

25、ps. NOTE 1 The tests in this standard are type tests. Requirements for testing individual convertors during production are not included. NOTE 2 Requirements for convertors which incorporate means for varying the lamp power are under consideration. NOTE 3 It may be expected that convertors complying

26、with this standard will ensure satisfactory operation between 92 % and 106 % of rated supply voltage of filament lamps with rated lives greater than 200 h and rated voltage less than 50 V. NOTE 4 There exist regional standards regarding the regulation of mains current harmonics for end-products such

27、 as luminaires and independent control gear. In a luminaire, the control gear is dominant in this respect. Control gear, together with other components, should comply with these standards. 2 Normative references The following referenced documents are indispensable for the application of this documen

28、t. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60357, Tungsten halogen lamps (non-vehicle) Performance specifications IEC 61347-1, Lamp controlgear Part 1: General and safety requi

29、rements IEC 61347-2-2, Lamp controlgear Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps 3 Terms and definitions For the purposes of this document the following terms and definitions apply. 3.1 total circuit power the total power dissipat

30、ed by convertor and lamp(s) in combination, at rated supply voltage of the convertor and at the highest rated output load 3.2 circuit power factor the ratio of measured circuit power to the product of the supply voltage (r.m.s.) and the supply current (r.m.s.) Page5 EN61047:2004 5 3.3 high power fac

31、tor convertor a convertor having a circuit power factor of at least 0,85 NOTE 1 For North America a high power factor is defined as a power factor of at least 0,9. NOTE 2 The value of the power factor takes into account the effect of the distortion of the current waveform. 3.4 high audio-frequency i

32、mpedance convertor a convertor the impedance of which in the frequency range 250 Hz to 2 000 Hz exceeds the values specified in Clause 11 3.5 short-circuit proof convertor a convertor which remains capable of functioning after an incidental overload or short circuit is removed and after restoration

33、of a protecting device, if any 4 General notes on tests 4.1 The tests according to this standard are type tests. NOTE The requirements and tolerances permitted by this standard are based on testing of a type test sample submitted by the manufacturer for that purpose. In principle this type test samp

34、le should consist of units having characteristics typical of the manufacturers production and be as close to the production centre point values as possible. It may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply wit

35、h the standard for the majority of the production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance of sampling plans and procedures for inspection by attributes, see IEC 60410. 4.2 For tests which are carried

36、 out with a lamp or lamps, this lamp(s) shall fulfill the following requirements. The wattage of the lamp(s) when measured at its rated lamp voltage (d.c. or a.c. 50 Hz/60 Hz) shall not differ from the rated wattage by more than 6 0 +%. 4.3 The tests shall be carried out in the order of the clauses,

37、 unless otherwise specified. 4.4 One specimen shall be submitted to all the tests. 4.5 In general all the tests are made on each type of convertor or, where a range of similar convertors is involved for each rated wattage in the range or on a representative selection from the range as agreed with th

38、e manufacturer. 4.6 The tests shall be made under the conditions specified in Annex A. Data of lamps not published in an IEC standard shall be made available by the lamp manufacturer. 4.7 All convertors covered by this standard shall comply with the requirements of IEC 61347-2-2 in conjunction with

39、IEC 61347-1. Page6 EN61047:2004 65 Classification 5.1 Classification according to the load a) Single value load convertors This type of convertor is designed for use with one specific output wattage only, which may be dissipated by one or more lamps. b) Multiple value load convertor This type of con

40、vertor is designed for use with one or more lamps with a total load within the declared wattage range. 5.2 Classification according to output voltage a) Convertors having a stabilized output voltage b) Convertors without a stabilized output voltage 6 Marking 6.1 Mandatory marking 6.1.1 Convertors sh

41、all be clearly marked as follows. a) Circuit power factor, e.g. = 0,9. If the power factor is less than 0,95 leading, it shall be followed by the letter “C“, e.g. = 0,9 C. b) If applicable, the symbol H which indicates that the convertor is not of the low distortion type. 6.1.2 In addition to the ab

42、ove mandatory marking, the following information shall either be given on the convertor or made available in the manufacturers catalogue or the like. a) If applicable, limits of the permissible temperature range. b) If applicable, an indication that the convertor has a stabilized output voltage. c)

43、If applicable,. an indication that the convertor is suitable for operation with a mains supply dimmer. 6.2 Optional marking The following information may either be given on the convertor or made available in the manufacturers catalogue or the like. a) Total circuit power. b) If applicable, the symbo

44、l Z , which indicates that the convertor is designed to comply with conditions for audio-frequency impedance. c) If applicable, a symbol which indicates that the convertor is a short-circuit proof type (the symbol is under consideration). Page7 EN61047:2004 7 7 Output voltage and current 7.1 Open-ci

45、rcuit voltage At any supply voltage between 92 % and 106 % of the rated supply voltage the open-circuit voltage shall not exceed 150 % of the rated output voltage. In case the output voltage is higher than 150 % of the rated value, the measurement shall be repeated and the convertor is shunted with

46、a resistor having a resistance value equal to min 2 output1 0 P ) (V ,where P minis the minimum wattage declared for the convertor. Under this condition the output voltage shall not exceed 150 % of the rated value. 7.2 Voltage during operation At rated supply voltage the output voltage shall not dif

47、fer by more than 4 8 +% from the lamp rated voltage. At any supply voltage between 92 % and 106 % of the rated supply voltage, the output voltage shall be between 84 % and 110 % of the rated value. Multiple load convertors shall be tested with both the minimum and maximum load. If a manufacturer dec

48、lares that his convertor has a stabilized output voltage, the output voltage shall be limited between 95 % and 105 % of its rated value at any supply voltage between 92 % and 106 % of the supply voltage and at any load within the specified wattage range. 7.3 Voltage surges during switching and opera

49、tion Voltage surges superimposed on the output voltage shall not exceed the values specified below (values under consideration). 7.4 Voltage waveform The maximum ratio of the peak value to the r.m.s. value shall not exceed 2,5 (value under consideration). 7.5 Inrush current At rated supply voltage, the lamp peak inrush current shall be not more than 10 times the steady-state r.m.s. lamp current at any load within the specified wattag