BS EN 60118-12-1997 Hearing aids - Dimensions of electrical connector systems《助听器 第12部分 电连接器系统尺寸》.pdf

《BS EN 60118-12-1997 Hearing aids - Dimensions of electrical connector systems《助听器 第12部分 电连接器系统尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60118-12-1997 Hearing aids - Dimensions of electrical connector systems《助听器 第12部分 电连接器系统尺寸》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60118-12:1997 IEC 60118-12: 1996 Hearing aids Part 12: Dimensions of electrical connector systems The European Standard EN 60118-12:1996 has the status of a British Standard ICS 17.140.50BSEN60118-12:1997 This British Standard, having been prepared under the directionof the El

2、ectrotechnical Sector Board, was published underthe authority of the Standards Board and comes into effect on 15 September 1997 BSI 09-1999 ISBN 0 580 27795 X National foreword This British Standard is the English language version of EN 60118-12:1996. It is identical with IEC 60118-12:1996. It super

3、sedes BS 2813 Specification for dimensions of plugs for hearing aids: 1981 which will be withdrawn on 1997-07-01. The UK participation in its preparation was entrusted to Technical Committee EPL/29, Electroacoustics, which has the responsibility to: aid enquirers to understand the text; present to t

4、he responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtain

5、ed on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers

6、 from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or Eur

7、opean publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract.

8、 Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 16 and

9、a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publications Amd. No. Date CommentsBSEN60118-12:1997 BSI 09-1999 i Contents Page National forew

10、ord Inside front cover Foreword 2 Text of EN 60118-12 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60118-12 October 1996 ICS 17.140.50; 31.220.10 Supersedes HD 304 S1:1977 Descriptors: Electroacoustics, hearing aids, junctions, dimensions, interchangeability English version Hearing

11、aids Part 12: Dimensions of electrical connector systems (IEC 118-12:1996) Appareils de correction auditive Partie 12: Dimensions des connecteurs lectriques (CEI 118-12:1996) Hrgerte Teil 12: Mae elektrischer Steckverbindersysteme (IEC 118-12:1996) This European Standard was approved by CENELEC on 1

12、996-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may b

13、e obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to th

14、e Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United K

15、ingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1996 Copyright reserved to CENELEC members Ref. No. EN 60118-12:1996 EEN60

16、118-12:1996 BSI 09-1999 2 Foreword The text of document 29/330/FDIS, future edition 1 of IEC 118-12, prepared by IEC TC 29, Electroacoustics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60118-12 on 1996-10-01. This European Standard supersedes HD304S1:1977. The f

17、ollowing dates were fixed: Endorsement notice The text of the International Standard IEC 118-12:1996 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1 Scope 3 2 Overview of connector systems 3 Annex A (informative) Recommended use ofcircularconnector

18、systems 16 Figure 1 Two-terminal polarized plug forearphones 7 Figure 2 Three-terminal unpolarized plugforearphones 8 Figure 3 Three-terminal polarized plugforelectrical input 9 Figure 4 Three-terminal plug 10 Figure 5 Four-terminal plug 11 Figure 6 Five-terminal plug 12 Figure 7 Three-terminal sock

19、et 13 Figure 8 Four-terminal socket 14 Figure 9 Five-terminal socket 15 Table 1 Overview of connector systems 3 Table 2 Dimensions of plugs shown in Figure 1,Figure 2and Figure 3 4 Table 3 Dimensions of plugs shown in Figure 4,Figure 5and Figure 6 5 Table 4 Dimensions of sockets shown in Figure 7, F

20、igure 8 and Figure 9 6 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1997-07-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1997-07-01EN60118-12:1996 BSI

21、09-1999 3 1 Scope This International Standard applies to plugs and connector systems for hearing aids and specifies the dimensions and their tolerances essential for ensuring interchangeability. 2 Overview of connector systems Table 1 Overview of connector systems System Application Dimensions (see

22、table) Figure Rectangular connector system Two-terminal polarized plug Earphones Table 2 Figure 1 Three-terminal unpolarized plug Earphones Table 2 Figure 2 Three-terminal polarized plug Electrical input Table 2 Figure 3 Circular connector system Three-terminal plug See Annex A Table 3 Figure 4 Thre

23、e-terminal socket See Annex A Table 4 Figure 7 Four-terminal plug See Annex A Table 3 Figure 5 Four-terminal socket See Annex A Table 4 Figure 8 Five-terminal plug See Annex A Table 3 Figure 6 Five-terminal socket See Annex A Table 4 Figure 9EN60118-12:1996 4 BSI 09-1999 Table 2 Dimensions of plugs

24、shown in Figure 1,Figure 2and Figure 3 Ref. Min. Nom. Max. Notes A 3,45 3,50 3,55 5 B 1,56 1,58 1,60 1,5 C 1,26 1,28 1,30 1,5 D 1,16 1,18 1,20 1,5 E 4,15 4,20 4,25 5 F 0,10 0,12 0,14 5 G 2,00 2,05 2,10 4,5 H 1,90 1,90 2,00 5 K 1,90 5 L 1,70 2,5 M 2,50 2,5 N 0,04 3,5 P 0,30 1,5 Q 5,70 5,90 6 4,5 R 0,

25、42 0,45 0,48 5 ! 35 35 37 6 NOTE 1The pins are cylindrical with conical ends; therefore dimensions B, C, D and P are diameters. NOTE 2The distances between the face of the plug body and the centre lines of the outer pins shall not exceed the indicated values K and L within the portion designated by

26、dimension M. Beyond M, these dimensions are not limited. NOTE 3Any deviation of the position of each of the centres of the pins away from their common centre line shall be within the indicated value N. The distances between the centre pin and each of the two outer pins, shall not differ more than th

27、e indicated valueN. NOTE 4When a sealing device is to be used with a plug, dimensions G and Q are to be measured to the face of the compressed device in order to place the grooves in position for correct detent action. When it is intended that a sealing device be used, it shall be supplied as part o

28、f the plug. NOTE 5Dimensions in millimetres. NOTE 6Angle in degrees.EN60118-12:1996 BSI 09-1999 5 Table 3 Dimensions of plugs shown in Figure 4,Figure 5and Figure 6 Ref. Min. Nom. Max. Notes B 2,03 2,05 2,05 1,5 C 0,60 2,6 D 0,38 0,40 0,40 4 E 0,66 0,68 0,70 8 F 0,76 0,78 0,80 8 G 0,35 0,35 0,37 2 H

29、 0,25 0,25 0,27 2 J 1,50 1,50 1,60 8 K 120 3,6 L 90 3,6 M 72 3,6 N 0,03 7 P 1,40 1,40 8 NOTE 1All dimensions are diameters, in millimetres. NOTE 2All dimensions are radii, in millimetres. NOTE 3All dimensions are angles, in degrees. NOTE 4The terminals are in the form of a hollow cylinder with diame

30、ter D. NOTE 5Geometric tolerancing (datum A). NOTE 6Basic dimensions. NOTE 7Positional tolerance zone. NOTE 8Dimensions, in millimetres.EN60118-12:1996 6 BSI 09-1999 Table 4 Dimensions of sockets shown in Figure 7, Figure 8 and Figure 9 Ref. Min. Nom. Max. Notes B 2,06 2,10 2,10 1,5 C 0,60 2,6 D 0,4

31、0 0,40 0,42 1 E 0,70 0,70 0,74 8 F 0,80 0,80 0,84 8 G 0,33 0,35 0,35 2 H 0,23 0,25 0,25 2 J 1,48 1,50 1,52 8 K 120 3,6 L 90 3,6 M 72 3,6 N 1,18 1,20 1,27 8 P 0,98 1,00 1,07 8 Q 0,15 0,20 0,20 2 R 0,30 0,30 0,35 1,4 S 1,22 1,25 1,28 8 T 0,03 7 NOTE 1All dimensions are diameters, in millimetres. NOTE

32、2All dimensions are radii, in millimetres. NOTE 3All dimensions are angles, in degrees. NOTE 4Colour marking. NOTE 5Geometric tolerancing (datum A). NOTE 6Basic dimensions. NOTE 7Positional tolerance zone. NOTE 8Dimensions, in millimetres.EN60118-12:1996 BSI 09-1999 7 For dimensions: see Table 2 Fig

33、ure 1 Two-terminal polarized plug for earphonesEN60118-12:1996 8 BSI 09-1999 For dimensions: see Table 2 Figure 2 Three-terminal unpolarized plug for earphonesEN60118-12:1996 BSI 09-1999 9 For dimensions: see Table 2 Figure 3 Three-terminal polarized plug for electrical inputEN60118-12:1996 10 BSI 0

34、9-1999 For dimensions: see Table 3 Figure 4 Three-terminal plugEN60118-12:1996 BSI 09-1999 11 For dimensions: see Table 3 Figure 5 Four-terminal plugEN60118-12:1996 12 BSI 09-1999 For dimensions: see Table 3 Figure 6 Five-terminal plugEN60118-12:1996 BSI 09-1999 13 For dimensions: see Table 4 Length

35、 of terminal 1 = N Length of other terminals = P Figure 7 Three-terminal socketEN60118-12:1996 14 BSI 09-1999 For dimensions: see Table 4 Length of terminal 1 = N Length of other terminals = P Figure 8 Four-terminal socketEN60118-12:1996 BSI 09-1999 15 For dimensions: see Table 4 Length of terminal

36、1 = N Length of other terminals = P Figure 9 Five-terminal socketEN60118-12:1996 16 BSI 09-1999 Annex A (informative) Recommended use of circular connector systems A.1 The three-terminal connector system is intended for use in connection with electrical input for hearing instruments as specified in

37、IEC 118-6 1)A.2 The four- and five terminal connector systems are mainly intended for use in connection with programmable hearing instruments. A.3 The longer pin (number 1) in Figure 7, Figure 8 and Figure 9 is recommended for use as a ground connection. 1) IEC 118-6:1984, Hearing aids Part 6: Chara

38、cteristics of electrical input circuits for hearing aids.17 blankBS EN 60118-12:1997 IEC 60118-12: 1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Eur

39、ope and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our produc

40、ts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an

41、 individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In respons

42、e to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through it

43、s Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards d

44、evelopments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publica

45、tions of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permiss

46、ion from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.