BS EN 16051-1-2012 Inflation devices and accessories for inflatable consumer products Compatibility of valves and valve adapters《充气消费产品用的充气装置及配件 阀门和阀门接头的兼容性》.pdf

《BS EN 16051-1-2012 Inflation devices and accessories for inflatable consumer products Compatibility of valves and valve adapters《充气消费产品用的充气装置及配件 阀门和阀门接头的兼容性》.pdf》由会员分享，可在线阅读，更多相关《BS EN 16051-1-2012 Inflation devices and accessories for inflatable consumer products Compatibility of valves and valve adapters《充气消费产品用的充气装置及配件 阀门和阀门接头的兼容性》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16051-1:2012Inflation devices andaccessories for inflatableconsumer productsPart 1: Compatibility of valves and valveadaptersBS EN 16051-1:2012 BRITISH STANDARDNational for

2、ewordThis British Standard is the UK implementation of EN 16051-1:2012.The UK participation in its preparation was entrusted to TechnicalCommittee SW/136/8, Swimming pools and aquatic equipment.A list of organizations represented on this committee can beobtained on request to its secretary.This publ

3、ication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012ISBN 978 0 580 69787 6ICS 23.080Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard

4、 was published under the authority of theStandards Policy and Strategy Committee on 31 January 2012.Amendments issued since publicationDate Text affectedBS EN 16051-1:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16051-1 January 2012 ICS 23.080 English Version Inflation devices and access

5、ories for inflatable consumer products - Part 1: Compatibility of valves and valve adapters Dispositifs et accessoires de gonflage pour biens de consommation gonflables - Partie 1: Compatibilit des valves et adaptateurs de valves Pumpen und Pumpenzubehr fr aufblasbare Verbraucherartikel - Teil 1: Ko

6、mpatibilitt von Ventilen und Ventiladaptern This European Standard was approved by CEN on 29 October 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterati

7、on. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by

8、 translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

9、Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION E

10、UROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16051-1:2012: EBS EN 16051-1:2012EN 16051-1:2012 (E) 2 Contents Page Foreword 3Introduction .41

11、 Scope 42 Normative references 43 Terms and definitions .54 Valves 64.1 Dimensions, designation 64.1.1 General 64.1.2 Screw valve with non-return device.64.1.3 Valve with non-return device and a twist lock closure . 104.1.4 Plug valve 114.2 Pressure classes. 124.3 Requirements and testing 134.3.1 Te

12、st conditions . 134.3.2 Requirements for valves with non-return device 13BS EN 16051-1:2012EN 16051-1:2012 (E) 3 Foreword This document (EN 16051-1:2012) has been prepared by Technical Committee CEN/TC 136 “Sports, playground and other recreational facilities and equipment”, the secretariat of which

13、 is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility

14、that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 16051, Inflation devices and accessories for inflatable consumer products, consists of the following parts: Part 1: Compa

15、tibility of valves and valve adapters Part 2: Safety requirements, durability, performance, compatibility and test methods of inflators According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Au

16、stria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kin

17、gdom. BS EN 16051-1:2012EN 16051-1:2012 (E) 4 Introduction The process of inflating a floating leisure article should be considered in two ways: a) the device for inflating the product, a pump; b) the compatibility between the pump and the valve or valves on the product itself. This standard, EN 160

18、51, is in two parts and addresses the performance, safety requirements, durability and test methods that should be applied to the pump and the compatibility between a pump and the device to be inflated to ensure that the inflation process can be conducted efficiently and safely. Unless a device is s

19、upplied and sold with a pump, by the manufacturer, where it is reasonable to expect the pump to be compatible with the product, there is generally a requirement to have an adaptor between a pump and the device valves to ensure that the air hose or other connector fits into or onto the valves on the

20、device. This part of the standard, Part 1, addresses the requirements for valves and where necessary, adaptors to ensure good fit and mechanical efficiency when inflating the device. 1 Scope This document specifies the valve side interface geometry between valves and pump adapters as well as strengt

21、h requirements of valves and valve adapters for inflatable consumer articles (see definition in 3.1). This document does not apply for valves of personal flotation devices according to EN ISO 12402; diving accessories and buoyancy compensators according to EN 1809. This document excludes the followi

22、ng valve types: valves used for bicycles and vehicles; needle valves (e. g. valves used for team sport balls). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated reference

23、s, the latest edition of the referenced document (including any amendments) applies. EN 16051-2, Inflation devices and accessories for inflatable consumer products Part 2: Safety requirements, durability, performance, compatibility and test methods of inflators BS EN 16051-1:2012EN 16051-1:2012 (E)

24、5 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 inflatable consumer articles group of articles and related accessories which are used for leisure purposes on land and water or in households or childrens play NOTE Typically these articles ar

25、e floating leisure devices for use on or in the water, small inflatable boats, air beds, air furniture, air mattresses, swimming aids, inflatable toys, aquatic toys etc. 3.2 valve device intended to inflate air chambers, to close the inflated air chambers and to deflate them after use 3.3 screw valv

26、e valve in which the connection of valve body to valve base and the connection between valve body and valve closure (cap, plug) is designed as a threaded connection 3.4 plug valve valve in which valve base and valve body form a unit and the closed condition is created by a plug inserted into the val

27、ve body 3.5 valve with twist lock closure connection with inflation device is sealed by a twist lock closure 3.6 non-return device valve component preventing air discharge even with the valve closure opened 3.7 valve without non-return device valve in which the escape of air is unimpeded after remov

28、al of the closure (cap, plug) 3.8 valve adapter device which provide compatibility between a pump and a valve 3.9 valve closure element which provides the main and/or final sealing function of the valve 3.10 interface those dimensional locations where the pump adapter and the valve connect 3.11 nomi

29、nal pressure working pressure defined by the manufacturer BS EN 16051-1:2012EN 16051-1:2012 (E) 6 4 Valves 4.1 Dimensions, designation 4.1.1 General Dimensions are given in millimetres. The valves need not correspond to the pictorial representations, only the interface dimensions specified have to b

30、e complied with. 4.1.2 Screw valve with non-return device Closure: Cap (see Figure 1) a) front view (with cap) b) sectional view (without cap) Key 1 tethering strap or anchors 2 valve closure (cap) 3 valve body 4 valve base with weld flange 5 back pressure seal diinner diameter of connection opening

31、 h minimum inner depth of connection opening Figure 1 Example of a screw valve with non-return device and cap without twist lock closure Design types: 1) Valve base screwed with air chamber sheeting; 2 Valve base welded with air chamber sheeting; 3) Valve body integrated into valve base; 4) Valve bo

32、dy screwed into valve base. Closure: Cap with twist lock closure (see Figure 4) BS EN 16051-1:2012EN 16051-1:2012 (E) 7 a) front view b) section side view c) bottom view Key diinner diameter of connection opening doouter diameter of connection opening h minimum inner depth of connection opening Figu

33、re 2 Example of a X-large screw valve with non-return device Valve adapters regarding the bayonet closure valve and the X-large screw valve have to be provided together with the product by the manufacturer. These adapters shall provide complete compatibility with the valve and the pump hose intermed

34、iate adapter as shown in Figure 3. This is not applicable if product and pump provide an independent system. BS EN 16051-1:2012EN 16051-1:2012 (E) 8 a) sectional view without cap b) top view Key diinner diameter of connection opening Figure 3 Intermediate adapter For typical connecting interface dim

35、ensions of screw valves with non-return device see Table 1. BS EN 16051-1:2012EN 16051-1:2012 (E) 9 Table 1 Typical connecting interface dimensions of screw valves with non-return device Valve size Symbol Inner diameter of connection openingMinimum inner depth of connection openingadihX-Large 4 46,8

36、 17 Large 3 31,0 13 Medium 2 24,0 13 Small 1 17,5 13 aMeasured from upper edge of valve body to the first constriction which is less than the nominal dimension or its lower tolerance. bold = preferred size and preferred dimensions BS EN 16051-1:2012EN 16051-1:2012 (E) 10 4.1.3 Valve with non-return

37、device and a twist lock closure a) pump adapter to twist lock closure valve b) sectional view c) interface details Key 1 tethering strap or anchors 2 non-return device 3 valve closure (cap) with twist lock closure 4 gasket 5 valve body 6 valve base 7 valve adapter with twist lock closure 8 base of n

38、on-return device diinner diameter For other details see Figure 1. Figure 4 Example of the valve with non-return device and cap with twist lock closure (typical dimensions) BS EN 16051-1:2012EN 16051-1:2012 (E) 11 4.1.4 Plug valve The shape of the valve describes the following characteristics of the

39、plug valve (see Figures 2 and 3): Valve body can be sunk into the outer skin “s“/“ns“ (sinkable/not sinkable). Non-return device: “w n-r“/“wo n-r“ (with/without non-return device). Assembly condition non-return device s/wn-r sinkable, with non-return device (for an example see Figure 5) s/wo n-r sin

40、kable, without non-return device (for an example see Figure 6) ns/w n-r not sinkable, with non-return device ns/wo n-r not sinkable, without non-return device For typical connecting interface dimensions of plug valves with or without non-return device see Table 2. a) in pulled-out condition b) in cl

41、osed-in condition c) detail of non-return flap Key 1 plug 2 securing device 3 valve body diinner diameter of connection opening doouter diameter of connection opening 4 valve base 5 back pressure flap 6 weld flange 2 mm a 3 mm h variable height Figure 5 Example of a plug valve, sinkable, with non-re

42、turn device (s/wn-r) BS EN 16051-1:2012EN 16051-1:2012 (E) 12 a) in pulled-out condition b) in closed-in condition Key 1 plug 2 securing device 3 valve body 4 valve base 5 weld flange diinner diameter of connection opening Figure 6 Example of a plug valve, sinkable, without non-return device (s/wo n

43、-r) Table 2 Typical connecting interface dimensions of plug valves with or without non-return device Valve size Symbol Inner diameter of valve bodyMinimum inner lengthof connection nozzlea dihXX large (XXL) 5 24 - X largeb (XL) 4 18 36 Large (l) 3 8,5 21 Medium (m) 2 7,5 21 Small (s) 1 6,5 21 aMeasu

44、red from the upper edge of the valve body to the first constriction which is less than the nominal dimension or its lower tolerance. bSpecial size, not covered by the pump/valve adapter. bold = preferred size and preferred dimensions 4.2 Pressure classes Depending on the permissible operating pressu

45、re (= nominal pressure) for which the article has been designed, valves are classified according to the following pressure classes: 0,3 bar pressure class A 0,8 bar 0,06 bar pressure class B 0,3 bar pressure class C 0,06 bar BS EN 16051-1:2012EN 16051-1:2012 (E) 13 4.3 Requirements and testing 4.3.1

46、 Test conditions Unless otherwise specified, tests shall be carried out at room temperature. 4.3.2 Requirements for valves with non-return device 4.3.2.1 Cap/plug Valves with a non-return device shall be equipped with a cap/plug including a securing device. 4.3.2.2 Securing device for all component

47、parts of valves 4.3.2.2.1 Requirement The individual components shall be connected with the valve in such manner which prevents that they can be lost even when opened unintentionally. The individual parts of the valve with non-return device shall remain securely connected to the air chamber even aft

48、er the cap or plug has been removed and/or the insert has been taken out (for quick deflating). 4.3.2.2.2 Testing Testing of the securing device is carried out using a force of 10 N at 40 C for a period of 10 min. With the cap/plug of the valve with non-return device opened, the test force is applie

49、d onto the securing device at 90 to the closure axis. 4.3.2.3 Retaining force between valve and adapter of inflation device 4.3.2.3.1 Requirement The connection between the valve and the adapter of the inflation device shall not become disengaged at 1,2 times the value of the nominal pressure. 4.3.2.3.2 Testing Testing is carried out using the adapter defined in EN 16051-2. The adapter is firmly attached by hand. This page deliberately left blankThis page deliberately left blankBSI is