BS EN 14121-2009 Aluminium and aluminium alloys - Sheet strip and plate for electrotechnical applications《铝和铝合金 电工用薄板材 带材和厚板材》.pdf

《BS EN 14121-2009 Aluminium and aluminium alloys - Sheet strip and plate for electrotechnical applications《铝和铝合金 电工用薄板材 带材和厚板材》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14121-2009 Aluminium and aluminium alloys - Sheet strip and plate for electrotechnical applications《铝和铝合金 电工用薄板材 带材和厚板材》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 14121:2009ICS 77.150.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAluminium andaluminium alloys Sheet, strip and platefor electrotechnicalapplicationsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on

2、 30 June2009. BSI 2009ISBN 978 0 580 64175 6Amendments/corrigenda issued since publicationDate CommentsBS EN 14121:2009National forewordThis British Standard is the UK implementation of EN 14121:2009. Itsupersedes BS EN 14121:2003 which is withdrawn.The UK participation in its preparation was entrus

3、ted to TechnicalCommittee NFE/35/5, Wrought Aluminium and Aluminium Alloys.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct ap

4、plication.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 14121:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14121May 2009ICS 77.150.10 Supersedes EN 14121:2003 English VersionAluminium and aluminium alloys - Sheet, strip and plate forelectrotechnical a

5、pplicationsAluminium et alliages daluminium - Tles, bandes et tlespaisses pour applications lectrotechniquesAluminium und Aluminiumlegierungen - Bnder, Blecheund Platten fr elektrotechnische AnwendungenThis European Standard was approved by CEN on 24 April 2009.CEN members are bound to comply with t

6、he CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre

7、or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial vers

8、ions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spai

9、n, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members

10、.Ref. No. EN 14121:2009: EBS EN 14121:2009EN 14121:2009 (E) 2 Contents Foreword 31 Scope 42 Normative references 43 Terms and definitions . 44 Ordering information . 45 Requirements . 55.1 Production and manufacturing processes . 55.2 Quality control 55.3 Chemical composition 55.4 Mechanical propert

11、ies and electrical conductivity 65.5 Freedom from defects . 75.6 Tolerances on dimensions and form . 75.7 Other properties . 76 Test methods 76.1 Chemical composition 76.2 Tensile test . 76.3 Electrical conductivity . 76.4 Measurement of dimensions 76.5 Surface finish . 76.6 Other tests 87 Inspectio

12、n documents . 88 Marking of products 89 Packing . 810 Arbitration . 8Bibliography 9BS EN 14121:2009EN 14121:2009 (E) 3 Foreword This document (EN 14121:2009) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European

13、 Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2009, and conflicting national standards shall be withdrawn at the latest by November 2009. Attention is drawn to the possibility that some of the eleme

14、nts of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable

15、and not discriminatory conditions, then this product shall be removed from the corresponding document. This document will supersede EN 14121:2003. Within its programme of work, CEN/TC 132 entrusted CEN/TC 132/WG 7 “Sheets, strips and plates“ to revise EN 14121. The following modifications were intro

16、duced in the standard: Table 1: EN AW-1370, EN AW-1370A, EN AW-6101B were added. Table 1: the value of the electrical conductivity of EN AW-1350 and EN AW-1350A, in temper H19, was corrected to 34,0. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the follo

17、wing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slov

18、enia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 14121:2009EN 14121:2009 (E) 4 1 Scope This European Standard specifies the technical conditions for inspection and delivery, the mechanical properties and electrical conductivity of wrought aluminium and aluminium alloys sheet, strip and

19、 plate for electrotechnical applications such as bus bars and other conductors, products requiring a certain minimum electrical conductivity. It applies to products with a thickness over 0,20 mm up to and including 150 mm. 2 Normative references The following referenced documents are indispensable f

20、or the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 485-3, Aluminium and aluminium alloys Sheet, strip and plate Part 3: Tolerances on dimensions and fo

21、rm for hot-rolled products EN 485-4, Aluminium and aluminium alloys Sheet, strip and plate Part 4: Tolerances on shape and dimensions for cold-rolled products EN 515, Aluminium and aluminium alloys Wrought products Temper designations EN 573-3, Aluminium and aluminium alloys Chemical composition and

22、 form of wrought products Part 3: Chemical composition and form of products EN 10002-1, Metallic materials Tensile testing Part 1: Method of test at ambient temperature EN 10204, Metallic products Types of inspection documents EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Par

23、t 1: General terms 3 Terms and definitions For the purposes of this European Standard the terms and definitions given in EN 12258-1:1998 apply. 4 Ordering information The ordering information shall define the product required and shall contain the following information: a) form and type of product:

24、1) form of the product (sheet, strip or plate); 2) designation of the aluminium and aluminium alloy; b) temper of the material for delivery according to EN 515 and, if different, the temper for use; c) number of this European Standard; d) dimensions and form of the product: 1) thickness, 2) width, B

25、S EN 14121:2009EN 14121:2009 (E) 5 3) length (in the rolling direction); e) tolerances on the dimensions and form, in accordance with EN 485-3 or EN 485-4; f) quantity: 1) mass or number of pieces, 2) quantity tolerances, if required; g) any requirements for inspection documents; h) any special requ

26、irements agreed between manufacturer and purchaser. If codified product designations are used, they should be in accordance with EN 573-5. 5 Requirements 5.1 Production and manufacturing processes Unless otherwise specified in the order, the production and manufacturing processes shall be left to th

27、e discretion of the manufacturer. 5.2 Quality control The manufacturer shall be responsible for the performance of all inspection and tests required by this standard prior to shipment of the product. If purchasers wish to inspect the product at the manufacturers works, they shall notify the manufact

28、urer at the time of ordering. 5.3 Chemical composition The chemical composition shall comply with the requirements specified in EN 573-3. BS EN 14121:2009EN 14121:2009 (E) 6 5.4 Mechanical properties and electrical conductivity The mechanical properties and electrical conductivity shall be in confor

29、mity with those specified in Table 1. Table 1 Mechanical properties and electrical conductivity Material temper Specified thickness Mechanical properties Electrical conductivityTensile strength 0,2 % proof stress Elongation Brinell hardness RmRp0,2A50 mmA HBWa20 C mm MPa MPa % % MS/m over up to min.

30、 max. min. min. min. approx. min. EN AW-1350AF EN AW-1350F 2,5 150 65a 34,5 EN AW-1350AO EN AW-1350O EN AW-1350AH111 EN AW-1350H111 0,20,51,53,06,012,5 0,5 1,5 3,0 6,0 12,5 20 65 65 65 65 65 65 105 105 105 105 105 105 20 20 20 20 20 20 20 22 26 29 35 32 20 20 20 20 20 20 35,4 EN AW-1350AH19 EN AW-13

31、50H19 0,2 3,0 150 130 1 45 34,0 EN AW-1350AH24 EN AW-1350H24 0,20,51,53,0 0,5 1,5 3,0 12,5 105 105 105 105 150 150 150 150 75 75 75 75 3 3 5 8 33 33 33 33 34,5 EN AW-1350AH26 EN AW-1350H26 0,20,51,5 0,5 1,5 4,0 120 120 120 165 165 165 90 90 90 2 3 4 38 38 38 34,5 EN AW-1350AH28 EN AW-1350H28 0,21,5

32、1,5 3,0 140 140 110 110 2 3 41 41 34,0 EN AW-1370AF EN AW-1370F 2,5 150 65a 34,7 EN AW-1370AO EN AW-1370O EN AW-1370AH111 EN AW-1370H111 0,20,51,53,06,012,5 0,5 1,5 3,0 6,0 12,5 20 65 65 65 65 65 65 105 105 105 105 105 105 20 20 20 20 20 20 20 22 26 29 35 32 20 20 20 20 20 20 35,8 EN AW-1370AH19 EN

33、AW-1370H19 0,2 3,0 150 130 1 45 34,7 EN AW-1370AH24 EN AW-1370H24 0,20,51,53,0 0,5 1,5 3,0 12,5 105 105 105 105 150 150 150 150 75 75 75 75 3 3 5 8 33 33 33 33 34,7 EN AW-1370AH26 EN AW-1370H26 0,20,51,5 0,5 1,5 4,0 120 120 120 165 165 165 90 90 90 2 3 4 38 38 38 34,7 EN AW-1370AH28 EN AW-1370H28 0,

34、21,5 1,5 3,0 140 140 110 110 2 3 41 41 34,2 EN AW-6101BT7 0,4 150 170 120 6 55 32,0 aFor information only. BS EN 14121:2009EN 14121:2009 (E) 7 5.5 Freedom from defects The product shall be free from defects prejudicial to its suitable and proper use. It shall have a smooth and clean surface. However

35、, small surface defects such as light scratches, indentations, laminations, stripes, roll marks, discolorations and non-uniform surface appearance resulting from heat treatment, etc., which cannot always be totally avoided, are generally permitted on both sides of the product. Whilst an operation de

36、signed to mask a fault is not permitted, the elimination of a superficial fault is permissible, provided that the dimensional tolerances and material properties continue to meet the specifications. 5.6 Tolerances on dimensions and form The tolerances on dimensions and form shall be in conformity wit

37、h EN 485-3 or EN 485-4. Other tolerances on dimensions and form shall be agreed between manufacturer and purchaser. 5.7 Other properties Additional requirements for properties such as hardness, bending ability etc., shall be agreed between manufacturer and purchaser. 6 Test methods 6.1 Chemical comp

38、osition The methods of analysis shall be at the discretion of the manufacturer. In case of dispute concerning the chemical composition, a referee analysis shall be carried out by methods agreed between manufacturer and purchaser. The results obtained by these methods shall be accepted. 6.2 Tensile t

39、est The tensile test shall be carried out in accordance with EN 10002-1. 6.3 Electrical conductivity The determination of electrical conductivity shall be carried out in accordance with a documented procedure giving details, such as a temperature between 15 C and 25 C. This procedure shall address t

40、he precision of the measurements and possible errors. Induction methods can be used for measurement of electrical conductivity, according to EN 2004-1, but for thin products, care shall be taken to avoid inaccuracy due to the penetration depth of the electrical field. 6.4 Measurement of dimensions T

41、he dimensions shall be measured by means of measuring instruments which are of an accuracy consistent with that of dimensions and the dimensional tolerances. All dimensions shall be checked at the ambient temperature in the workshop or laboratory, and, in case of dispute, at a temperature between 15

42、 C and 25 C. 6.5 Surface finish Unless otherwise specified, examination of surface finish shall be carried out without the assistance of magnifying apparatus on products before delivery. BS EN 14121:2009EN 14121:2009 (E) 8 6.6 Other tests If other mechanical or physical tests are required, these sha

43、ll be agreed between manufacturer and purchaser. These tests shall be carried out either in accordance with the existing European Standards or agreed upon by manufacturer and purchaser. The following standards may be used as guidelines: a) the Brinell hardness (HBW) in accordance with EN ISO 6506-1;

44、 b) erichsen test: in accordance with ISO 8490; c) earing test: in accordance with EN 1669. 7 Inspection documents When requested by the purchaser and agreed by the manufacturer, the manufacturer shall provide the appropriate inspection document in accordance with EN 10204. 8 Marking of products Mar

45、king of products shall be undertaken when agreed between manufacturer and purchaser and stated on the order. This marking shall not adversely affect the final use of the product. 9 Packing Unless otherwise specified in European Standards relating to special products or specified in the order, the me

46、thod of packing shall be determined by the manufacturer who shall take all suitable precautions to ensure that, under the usual conditions of transportation, the products will be delivered in a condition suitable for use. 10 Arbitration In cases of dispute concerning conformity with the requirements

47、 of this European Standard and before any decision is made to reject the products, testing and examination shall be carried out by an arbitrator chosen by mutual agreement between manufacturer and purchaser. The arbitrators decision shall be final. BS EN 14121:2009EN 14121:2009 (E) 9 Bibliography 1

48、EN 485-1, Aluminium and aluminium alloys Sheet, strip and plate Part 1: Technical conditions for inspection and delivery 2 EN 573-5, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 5: Codification of standardized wrought products 3 EN 1669, Aluminium and aluminium alloys Test methods Earing test for sheet and strip 4 EN 2004-1, Aerospace series Test methods for aluminium and aluminium alloy products Part 1: Determination of electrical conductivity of wrought aluminium alloys 5 EN ISO 6506-1, Metallic materials Brinell hardness te