BS 6057-3 17-1990 Rubber latices - Methods of test - Determination of bound styrene content of non-reinforced styrene butadiene rubber latices《橡胶乳 第3部分 试验方法 第17节 非增强丁苯橡胶乳粘合苯乙烯含量测定》.pdf

《BS 6057-3 17-1990 Rubber latices - Methods of test - Determination of bound styrene content of non-reinforced styrene butadiene rubber latices《橡胶乳 第3部分 试验方法 第17节 非增强丁苯橡胶乳粘合苯乙烯含量测定》.pdf》由会员分享，可在线阅读，更多相关《BS 6057-3 17-1990 Rubber latices - Methods of test - Determination of bound styrene content of non-reinforced styrene butadiene rubber latices《橡胶乳 第3部分 试验方法 第17节 非增强丁苯橡胶乳粘合苯乙烯含量测定》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 6057-3.17: 1990 ISO 3136:1983 Rubber latices Part 3: Methods of test Section 3.17 Determination of bound styrene content of non-reinforced styrene butadiene rubber latices NOTEAttention is drawn to BS 6057-0 “General introduction”, issued separately.BS6057-3.17:1990 This British

2、Standard, having been prepared under the directionof the Rubber StandardsPolicy Committee, waspublished under the authorityof the Board of BSIandcomes into effect on 31 August 1990 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference RUM/38 Draft announce

3、d in BSI News July 1990 ISBN 0 580 18866 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Rubber Standards Policy Committee (RUM/-) to Technical Committee RUM/38, upon which the following bodies were represented: British Rubber Manufact

4、urers Association Malaysian Rubber Producers Research Association Medical Sterile Products Association Tropical Growers Association Amendments issued since publication Amd. No. Date CommentsBS6057-3.17:1990 BSI 12-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1

5、Scope and field of application 1 2 References 1 3 Principle 1 4 Reagents and apparatus 1 5 Sampling 1 6 Procedure 1 7 Expression of results 1 8 Test report 1 Publication(s) referred to Inside back coverBS6057-3.17:1990 ii BSI 12-1999 National foreword This Section ofBS6057 has been prepared under th

6、e direction of the Rubber Standards Policy Committee and is identical withISO3136:1983 “Rubber latex styrene-butadiene Determination of bound styrene content” published by the International Organization for Standardization (ISO). It supersedes clause8.1 ofBS3397:1976, which is deleted by amendment.

7、A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International Standard C

8、orresponding British Standard ISO 123:1985 BS 6057 Rubber latices Part 2:1987 Sampling (Identical) ISO 2028:1989 Section 3.16:1990 Preparation of dry polymer from synthetic latices (Identical) ISO 2453:1975 BS 1673 Methods of test for raw rubber and unvulcanized compounded rubber Section 5.1:1963 Bo

9、und styrene content (Technically equivalent) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be

10、indicated in the amendment table on the inside front cover.BS6057-3.17:1990 BSI 12-1999 1 1 Scope and field of application This International Standard specifies a method for the determination of the bound styrene content of styrene-butadiene rubber (SBR) latices. The method is applicable to hot (app

11、roximately50 C) emulsion polymerized SBR latices having a bound styrene content, expressed on the SBR content, of up to55% and to cold (approximately5 C) emulsion polymerized SBR latices having a bound styrene content between18and40%. The method is not applicable to reinforced styrene-butadiene rubb

12、er (SBRY) latices, carboxylated-styrene-butadiene rubber (XSBR) latices and pyridine-styrene-butadiene rubber (PSBR) latices. 2 References ISO 123, Rubber latex Sampling. ISO 2028, Rubber Synthetic latices Preparation of dry polymer. ISO 2453, Styrene-butadiene copolymers Determination of bound styr

13、ene content. 3 Principle Conversion of the latex to a dry polymer which is extracted and pressed into a thin sheet. Calculation of the bound styrene content from the measured refractive index of this sheet. 4 Reagents and apparatus The reagents and apparatus specified inISO2028 andISO2453 are requir

14、ed. 5 Sampling Sampling shall be carried out in accordance with one of the methods specified inISO123. 6 Procedure In accordance withISO2028, coagulate the latex with sodium chloride and sulphuric acid in the presence of methanol and collect and dry the resultant crumb. In accordance withISO2453, sh

15、eet out the polymer, extract with ethanol-toluene azeotrope, dry, press into a thin sheet and determine the refractive index. 7 Expression of results Calculate the bound styrene content, as a percentage by mass of the SBR content of the latex, in accordance withISO2453. 8 Test report The test report

16、 shall include the following information: a) the reference of the method used; b) the results and the method of expression used; c) any unusual features noted during the determination; d) any operation not included in this International Standard, or regarded as optional.2 blankBS6057-3.17:1990 BSI 1

17、2-1999 Publication(s) referred to See national foreword.BS 6057-3.17: 1990 ISO 3136:1983 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the

18、international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services

19、. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual upd

20、ating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for

21、 international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and i

22、ts Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and

23、 receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the in

24、ternational standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.

25、This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.