ASTM F3264-2018 Standard Specification for Normal Category Aeroplanes Certification《普通类飞机认证标准规范》.pdf
《ASTM F3264-2018 Standard Specification for Normal Category Aeroplanes Certification《普通类飞机认证标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F3264-2018 Standard Specification for Normal Category Aeroplanes Certification《普通类飞机认证标准规范》.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F3264 18Standard Specification forNormal Category Aeroplanes Certification1This standard is issued under the fixed designation F3264; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number
2、in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 Applicability:1.1.1 This specification identifies the industry standardswhich have been determined by consensus to demonstratecompliance to th
3、e requirements (“the Rules”) for Level 1, 2, 3,4 Normal Category Aeroplanes.1.1.2 Only standards that are considered mature enough forgeneral application to certification projects and have beenfound acceptable by committee consensus to propose to theCAAs for acceptance as a Means of Compliance to th
4、eir Rulesare included.1.1.3 In the event that a particular CAAs requirements arenot harmonized with the other CAAs requirements, the stan-dards will be written to include the non-harmonized require-ments as well as the harmonized requirements with theapplicability defined in the standard.1.2 Civil A
5、viation Authorities:1.2.1 CAAs may accept a specific revision of this specifi-cation as an acceptable Means of Compliance (MoC) to theirrequirements. Acceptance and applicability as a MoC to theCAAs airworthiness rules remains the decision of the respec-tive CAAs. CAAs may accept this specification,
6、 with orwithout limitations as defined in their specification acceptancedocument. For information on which CAAs have acceptedthese standards (in whole or in part) as an acceptable MoC totheir Rules, refer to the ASTM F44 webpage (www.astm.org/COMMITTEE/F44.htm) which includes CAA website links.1.3 A
7、pplicant Responsibility:1.3.1 The applicant must seek individual guidance fromtheir respective CAA concerning the use of this specificationand any referenced Specifications, Practices, Test Methods, orGuides to show compliance to the CAA rules. Alternatively, anapplicant may propose a MoC other than
8、 those included in thisspecification but it is their responsibility to obtain acceptanceof their proposed MoC from their CAA.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDe
9、velopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2NOTE 1Referenced ASTM standards are listed in Sections 510ofthis specification.F2490 Guide for Aircraft Elect
10、rical Load and Power SourceCapacity AnalysisF3060 Terminology for AircraftF3061/F3061M Specification for Systems and Equipment inSmall AircraftF3062/F3062M Specification for Aircraft Powerplant Instal-lationF3063/F3063M Specification for Aircraft Fuel and EnergyStorage and DeliveryF3064/F3064M Speci
11、fication for Aircraft PowerplantControl, Operation, and IndicationF3065/F3065M Specification for Aircraft Propeller SystemInstallationF3066/F3066M Specification for Aircraft Powerplant Instal-lation Hazard MitigationF3082/F3082M Specification for Weights and Centers ofGravity of AircraftF3083/F3083M
12、 Specification for Emergency Conditions,Occupant Safety and AccommodationsF3093/F3093M Specification for Aeroelasticity Require-mentsF3114 Specification for StructuresF3115/F3115M Specification for Structural Durability forSmall AirplanesF3116/F3116M Specification for Design Loads and Condi-tionsF31
13、17 Specification for Crew Interface in AircraftF3120/F3120M Specification for Ice Protection for GeneralAviation Aircraft1This specification is under the jurisdiction ofASTM Committee F44 on GeneralAviation Aircraft and is the direct responsibility of Subcommittee F44.10 onGeneral.Current edition ap
14、proved March 1, 2018. Published March 2018. Originallyapproved in 2017. Last previous edition approved in 2017 as F3264 17. DOI:10.1520/F3264-18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards
15、volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on s
16、tandardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1F3173/F3173M Specification for Aircraft Handling Charac-teristicsF3174/F3174M Specifi
17、cation for Establishing OperatingLimitations and Information for AeroplanesF3179/F3179M Specification for Performance ofAeroplanesF3180/F3180M Specification for Low-Speed Flight Charac-teristics of AircraftF3227/F3227M Specification for Environmental Systems inSmall AircraftF3228 Specification for F
18、light Data and Voice Recording inSmall AircraftF3229/F3229M Practice for Static Pressure System Tests inSmall AircraftF3230 Practice for Safety Assessment of Systems andEquipment in Small AircraftF3231/F3231M Specification for Electrical Systems inSmall AircraftF3232/F3232M Specification for Flight
19、Controls in SmallAircraftF3233/F3233M Specification for Instrumentation in SmallAircraftF3234/F3234M Specification for Exterior Lighting in SmallAircraftF3235 Specification for Aircraft Storage BatteriesF3236 Specification for High Intensity Radiated Field(HIRF) Protection in Small Aircraft2.2 Feder
20、al Aviation Administration (FAA) Regulations:14 CFR 23, Amendment 64 Airworthiness Standards: Nor-mal Category Airplanes32.3 European Aviation Safety Agency (EASA) Regulations:CS 23, Amendment 5 Certification Specifications for Nor-mal Category Aeroplanes4NOTE 2The above regulations and requirements
21、 are not directlyreferenced in the specification but are the “relevant applicable regulations”referred to in the Rules definition in 3.2.2.3. Terminology3.1 Unique and Common TerminologyTerminology usedin multiple standards is defined in F3060,Aircraft TerminologyStandard. Terminology that is unique
22、 to this specification isdefined in this section.3.2 Definitions:3.2.1 Means of Compliance (MoC)a method or processwhich is used to show that a rule has been complied withthrough either design, analysis, test, or a combination ofdesign, analysis and test.3.2.2 Rulesuniversal reference to the relevan
23、t applicableregulations or standards governing airworthiness requirementsfor Normal Category Aeroplanes issued by the CAAs.3.3 Abbreviations:3.3.1 CAACivil Aviation Authority3.3.2 MoCMeans of Compliance4. General4.1 Regulatory Applicability and Definitions:4.1.1 See the applicable CAA Rules for spec
24、ific CAAsApplicability and Definitions. There are currently no standardswritten or anticipated for these requirements.4.2 Certification of Normal Category Aeroplanes:4.2.1 This specification will identify in Sections 510allstandards that are applicable for certifying a Level 1, 2, 3, or 4Normal Cate
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF32642018STANDARDSPECIFICATIONFORNORMALCATEGORYAEROPLANESCERTIFICATION 普通 飞机 认证 标准规范 PDF

链接地址:http://www.mydoc123.com/p-540199.html