ASTM D471-2015 Standard Test Method for Rubber Property&x2014 Effect of Liquids《液体对橡胶性能影响的标准试验方法》.pdf
《ASTM D471-2015 Standard Test Method for Rubber Property&x2014 Effect of Liquids《液体对橡胶性能影响的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM D471-2015 Standard Test Method for Rubber Property&x2014 Effect of Liquids《液体对橡胶性能影响的标准试验方法》.pdf(19页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D471 12aD471 15Standard Test Method forRubber PropertyEffect of Liquids1This standard is issued under the fixed designation D471; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in p
2、arentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This test method covers the required procedures to evaluate
3、the comparative ability of rubber and rubber-like compositionsto withstand the effect of liquids. It is designed for testing: (1) specimens of vulcanized rubber cut from standard sheets (seePractice D3182), (2) specimens cut from fabric coated with vulcanized rubber (see Test Methods D751), or (3) f
4、inished articlesof commerce (see Practice D3183). This test method is not applicable to the testing of cellular rubbers, porous compositions, andcompressed sheet packing, except as described in 11.2.212.2.2.1.2 Periodically, it is necessary to produce a new lot of an IRM oil to replace the dwindling
5、 supply of the current product. TheChairman of the subcommittee shall have the authority to approve the production of a replacement lot. Once produced, thetechnical data of the new lot shall be presented, in a comparative fashion, to that of the existing lot and balloted upon by themembership of the
6、 D11.15 subcommittee and, either subsequently or concurrently, balloted upon by the membership of the D11main committee for approval to release the new lot for distribution.1.3 In the event that an IRM oil becomes unavailable for distribution due to depletion, the Chairman of the subcommittee shallh
7、ave the authority to approve production of a new lot and, after a meeting of the task group, regularly scheduled, or not, to releasea quantity of the product for distribution sufficient enough only to address a backlog. Once the backlog is addressed, the processdescribed in 1.2 shall be followed.1.4
8、 ASTM Oils No. 2 and No. 3, formerly used in this test method as standard test liquids, are no longer commercially availableand in 1993 were replaced with IRM 902 and IRM 903, respectively (see Appendix X1 for details).1.5 ASTM No. 1 Oil, previously used in this test method as a standard test liquid
9、, is no longer commercially available and in2005 was replaced with IRM 901; refer to Table 1 and Appendix X3 for details.1.6 ASTM No. 5 Oil was accepted into Specification D5900 as an industry reference material in 2010 and designated as IRM905. The composition, and properties of this immersion oil
10、were not changed and the data in Table 1 remains current. Refer toAppendix X4 for other details.1.7 The specifications and properties listed in Table 1 for IRM 901, IRM 902, IRM 903, and IRM 905 are also maintained inSpecification D5900.1.7.1 The subcommittee responsible for maintaining Test Method
11、D471, presently D11.15, shall review the data in SpecificationD5900 to ensure that it is identical to that which appears in Test Method D471. This shall be accomplished at the time of the 5year review or more frequently when necessary.1.8 Historical, technical, and background information regarding t
12、he conversion from ASTM No. 1, ASTM No. 2, and ASTMNo. 3 Oils to IRM 901, IRM 902, and IRM 903 immersion oils is maintained in Practice D5964.1.8.1 The subcommittee responsible for maintaining Test Method D471, presently D11.15, shall review the data in PracticeD5964 to ensure that it is identical t
13、o that which appears in Test Method D471. This shall be accomplished at the time of the 5year review or more frequently when necessary.1.9 This test method includes the following:1 This test method is under the jurisdiction of ASTM Committee D11 on Rubber and is the direct responsibility of Subcommi
14、ttee D11.15 on Degradation Tests.Current edition approved Dec. 1, 2012July 1, 2015. Published January 2013October 2015. Originally approved in 1937. Last previous edition approved in 2012 asD471 12.D471 12a. DOI: 10.1520/D0471-12A.10.1520/D0471-15.This document is not an ASTM standard and is intende
15、d only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current
16、versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1Change in Mass (after immersion) Section 10Change in Volume (after immersion) Section 11Dimensional-
17、Change Method for Water-Insoluble Liq-uids and Mixed Liquids Section 12Change in Mass with Liquid on One Surface Only Section 13Determining Mass of Soluble Matter Extracted by theLiquid Section 14Change in Tensile Strength, Elongation and Hardness(after immersion) Section 15Change in Breaking Resist
18、ance, Burst Strength, TearStrength and Adhesion for Coated Fabrics Section 16Calculation (of test results) Section 17TABLE 1 Specifications and Typical Properties of IRM Reference OilsProperty IRM 901A IRM 902 IRM 903 IRM 905 ASTM MethodSpecified Properties:Aniline Point, C (F) 124 1 (255 2) 93 3 (1
19、99 5) 70 1 (158 2) 115 1 (239 2) D611Aniline Point, C (F) 124 1 (255 2) 93 3 (199 5) 70 1 (158 2) 115 1 (239 2) D611Kinematic Viscosity(mm2/s cSt)38C (100F) . 31.934.1 . D44599C (210F) 18.1220.34 19.221.5 . 10.811.9 D445Gravity, API, 16C(60F)28.8 1 19.021.0 21.023.0 . D287Viscosity-Gravity Con-stant
20、0.7900.805 0.8600.870 0.8750.885 . D2140Viscosity-Gravity Con-stant0.7900.805 0.8600.870 0.8750.885 . D2501Flash Point COC, C(F)243(469) min 232 (450) min 163 (325) min 243 (469) min D92Naphthenics, CN (%) 27 (avg) 35 min 40 min . D2140Paraffinics, CP (%) 65 min 50 max 45 max . D2140Typical Properti
21、es:Pour Point, C (F) 12 (10) 12 (10) 31 (24) 15 (5) D97ASTM Color L 3.5 L 2.5 L 0.5 L 1.0 D1500Refractive Index 1.4848 1.5105 1.5026 1.4808 D1747UV Absorbance, 260 nm 0.8 4.0 2.2 . D2008Aromatics, CA (%) 3 12 14 4 D2140A Refer to Appendix X3. Table X3.1 reflects the differences in the properties bet
22、ween ASTM No. 1 Oil and IRM 901 for reference purposes.TABLE 2 IRM 901 2012 Batch Test ResultsProperty Method 2005 BatchCOA 2005 BatchCurrent 2012 Sample Data 2012 BatchAverageViscosity, cSt99C D445 19.58 19.518.8 18.7 18.8 18.7 18.818.8 18.8 18.9 18.7Gravity, API16C D287 28.6 28.928.9 28.9 28.8 28.
23、9 28.928.9 28.9 28.9 28.9Flash PointCOC, C D92 287 313306 289 292 288 296299 303 294 294Aniline Point,C D611 123.8 124.7124.8 124.8 124.7 124.3 124.5124.8 124.8 124.9 124.6Viscosity-Gravity Con-stantD2140 0.796 0.7980.799 0.799 0.800 0.7990.799Viscosity-Gravity Con-stantD2501 0.796 0.798 0.7990.7990
24、.799 0.799 0.799 0.799Naphthenics,Cn% D2140 2426 26 27 28 2726 26 27 29Paraffinics,Cp% D2140 70 7271 71 69 70 7171 71 71 70D471 152Change in Mass (after immersion) Section 11Change in Volume (after immersion) Section 12Dimensional-Change Method for Water-Insoluble Liq-uids and Mixed Liquids Section
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD4712015STANDARDTESTMETHODFORRUBBERPROPERTYX2014EFFECTOFLIQUIDS 液体 橡胶 性能 影响 标准 试验 方法 PDF

链接地址:http://www.mydoc123.com/p-511764.html