ARMY MS24539 REV D-1985 TRANSMITTER PRESSURE - 24 VOLT DC 120 PSI《24伏特直流电 120帕每平方英尺的压力变送器》.pdf

《ARMY MS24539 REV D-1985 TRANSMITTER PRESSURE - 24 VOLT DC 120 PSI《24伏特直流电 120帕每平方英尺的压力变送器》.pdf》由会员分享，可在线阅读，更多相关《ARMY MS24539 REV D-1985 TRANSMITTER PRESSURE - 24 VOLT DC 120 PSI《24伏特直流电 120帕每平方英尺的压力变送器》.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、MSZLi539 REV D bb m 9799912 0007257 7 m FayLCiL I 6620 I -2T6 3. -4 MAX. DIA. CALIBRATION DATA (LB PER SQUARE INCH) (oms) 20 4.5 TO 6.0 30 7.0 TO 8.5 9.0 TO 11.0 40 50 11.5 TO 13.5 I 60 I 14.0 TO 16.0 I 70 . 16.5 TO 18.5 80 18.5 TO 21.0 90 21.0 TO 23.5 100 I 23.0 TO 26.0 I 110 25.5 TO 28.5 120 28.0

2、TO 31.0 i REQUIREMENTS: 1. TYPE III (PRESSURE), UNIT 2 (TRANSMITTER) OF PROCUREMENT SPECIFICATION. 2. TRANSMITTER MUST OPERATE PROPERLY, LINEARLY, AND ACCURATELY THROUGHOUT THE RANGE OF O - 120 PSI WHEN CONNECTED TO THE ASSOCIATED INDICATOR, HS24540. CALIBRATION DATA IS REQUIRE0 FOR INITIAL CALIBRAT

3、ION PURPOSES. DURING A TEST OR SUBSEQUENT TO A TEST, THEN CALIBRATE AT O, 20, 70, AND 120 PSI ONLY. INSTRUMENTATION USE0 TO MEASURE RESISTANCE SHALL BE ACCURATE WITHIN 3. WHEN CALIBRATION IS REQUIRED 4. 0.5 PERCENT OF SCALE READING. 5. TRANSMITTER INTERNAL RESISTANCE ELEMENT SHALL BE OF WIRE-WOUND C

4、ONSTRUCTION. RESISTANCE SHALL NOT BE ACCEPTABLE. THIN FILM OR THICK FILM 6. SCREW THREADS SHALL BE IN ACCORDANCE WITH FED-STD-H28/2. 7. MARKING SHALL CONSIST OF THE MS PART NUMBER AND THE MANUFACTURERS IDENTIFICATION IN ACCORDANCE WITH MIL-STD-130. NOTES: 1. DIMENSIONS ARE IN INCHES. UNLESS OTHERWIS

5、E SPECIFIED, TOLERANCES ARE 1/64. 2. 3. FOR DESIGN FEATURE PURPOSES, THIS STANDARD TAKES PRECEDENCE OVER PROCUREMENT DOCUMENTS REFERENCED HEREIN. THIS STANDARD 15 NOT INTENDED TO LIMIT CONSTRUCTION TO FEATURES OTHER THAN AS SHOWN HEREON BY DIMENSIONS, NOTATIONS, ANO REFERENCED DOCUMENTS. REFERENCED

6、DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BIDS. THE USE OF RECYCLE0 MATERIALS WHICH MEET THE REQUIREMENTS OF THE APPLICABLE MATERIAL SPECIFICATION WITH- OUT JEOPARDIZING THE INTENDED USE OF THE ITEM SHALL BE ENCOURAGED. 4. 5. ENGINEERING IMC PART NO. DWG NO. i -. . DENOTES

7、CHANGES MS24539-1 I 8376928 ARMY-AT TITLE M Il ITARY ST AM DARD .A iMITTER, PRESSURE- r DC 12OPSI IhK 34539 lther Cust TRANS 1“d L I AF-99 24 VOL NAVY-Y D PROCUREMENT SPECIFICATION SUPERSEDES SHEET I OF I MIL-I- 10986 _. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-