ARMY MIL-STD-299-1957 VISUAL INSPECTION STANDARDS FOR NAILED WOOD BOXES AND WIREBOUND WOOD BOXES USED IN SMALL ARMS AMMUNITION PACKING《轻武器弹药包装使用的固定木箱和金属线螺旋钉的木箱的视觉检验标准》.pdf

《ARMY MIL-STD-299-1957 VISUAL INSPECTION STANDARDS FOR NAILED WOOD BOXES AND WIREBOUND WOOD BOXES USED IN SMALL ARMS AMMUNITION PACKING《轻武器弹药包装使用的固定木箱和金属线螺旋钉的木箱的视觉检验标准》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-STD-299-1957 VISUAL INSPECTION STANDARDS FOR NAILED WOOD BOXES AND WIREBOUND WOOD BOXES USED IN SMALL ARMS AMMUNITION PACKING《轻武器弹药包装使用的固定木箱和金属线螺旋钉的木箱的视觉检验标准》.pdf（83页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-STD-299 17 January 1957 SUPERSEDES ORD-SIP-S32i 1 October 1945 MI LI TARY STAN DARD VISUAL INSPECTION STANDARDS FOR NAILED WOOD BOXES AND. WIREBOUND WOOD BOXES USED IN SMALL ARMS AMMUNITION PACKING b THIS DOCUMENT CONTAINS $3 PAGES. Provided by IHSNot for ResaleNo reproduction or networking perm

2、itted without license from IHS-,-,-I _- MIL-STD-297 1 77997L1 0069355 2 Mll-ST.D-299 17 January 1957 OFFICE OF THE ASSISTANT SECRETARY OF DEFENSE WASHINGTON 25, D. C. Supply and Logistics Visual Inspection Standards for Nailed Wood Boxes and Wirebound Wood Boxes Used in Small Arms Ammunition Packing

3、 MILSTD-299 17 JANUARY 1957 1. This Standard has been approved by the Department of Defense and is mandatory for use 2. In accordance with established procedure the Standardization Division has deqignated 3. Recommended corrections, additions, or deletions should be addressed to the Standardiza- by

4、the Departments of the Army, the Navy, and the Air Force, effective 1 March 1957. the Ordnance Corps, Department of the Army as custodian of this Standard. tion Division, Office of the Assistant Secretary of Defense (Supply and Logistics), Washington 25, D. C. ii Provided by IHSNot for ResaleNo repr

5、oduction or networking permitted without license from IHS-,-,-FOREWORD This standard was prepared under the direction of the Office, Chief of Ordnance, to be used to supplement specifications for nailed mood boxes and wirebound wood boxes used in the packing of small arms ammunition. It replaces the

6、 following publications on the same subject: ORDSIPS321, 1 October 1945 and ORDSIPS321, Amendment 1, March 1954. This publication serves to create a military standard which evaluates and illustrates a practical majority of defects and mas assembled as a result of extensive surveys covering wood box

7、and small arms ammunition manufactur- ing facilities. The format used retains most of the features of the formats of the publica- tions it replaces because experience hm proved that the numbering of illustra- tions to conform to the numbering of visual defects in the applicable detailed specificatio

8、ns, special treatment of indexes and specialized grouping have served to facilitate inspection, training and general use. iii Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-277 81 m 7777731 0067357 6 m MI 1-STD-299 17 January 1957 CONTENTS 1

9、. SCOPE AND PURPOSE 1.1 SCOPE 1.2 PURPOSE 2. REFERENCED DOCUMENTS 2.1 STANDARDS 3. DEFINITIONS 3.1 GENERAL 3.2 SPECIFIC 3.2.1 Permissible Defect 4. GENERAL REQUIREMENTS 4.1 GENERAL 5. DETAIL REQUIREMENTS 5.1 DEFECT GROUPING V Provided by IHSNot for ResaleNo reproduction or networking permitted witho

10、ut license from IHS-,-,-1. SCOPE AND PURPOSE 1.1 Scope. This standard provides illus- trations and procedures for determining and evaluating defects normally found in nailed wood packing boxes and wirebound packing boxes used as shipping and storage containers for small arms ammunition and the stand

11、ard shall be used as a supplement to pertinent specifications. .1.2 Purpose. The purpose of this standard is to: (a) Provide a standard basis for the inspec- tion of small arms ammunition nailed wood and wirebound packing boxes. (b) Serve as an instruction manual for use in training personnel engage

12、d in packing or in inspection of small arms ammunition boxes. (c) Provide visual defect standards for use in connection with acceptance inspection of packed ammunition. MIL-STD-299 17 January 1957 (d) Promote the standardization of manu- facturing and inspection of small arms ammuni- tion boxes. 2.

13、REFERENCED DOCU- MENTS 2.1 Standards. MILSTD-1054ampling Procedures and Tables for Inspection by Attributes. 3. DEFINITIONS 3.1 General. Definitions of Standard MIL- STD-105 are applicable. 3.2 Specific. For the purpose of this stand- ard the following definition applies: 3.2.1 Pemksible deject. A c

14、ondition which, though not desirable from an appearance standpoint, may be permitted for reasons of economy. 1 .- ,-? 6 .I .-;- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-277 L 97777LL 0069357 T m MIL-STD-299 17 January 1957 4. GENERAL R

15、EQUIRE- MENTS 4.1 General. The descriptions and defini- tions of defects established in this standard are those commonly occurring. Any other defects not listed, present in the lot, shall be reported. If, in the opinion of the Government inspector, the other defects be serious, complete informa- tio

16、n, recommendations and request for disposi- tion shall be submitted through proper channels. 5. DETAIL REQUIREMENTS 5.1 Defect grouping. For convenience in referencing, the defect lists and defect photo- graphs are grouped as follows: Nailed Wood Boxes: Pages List of Defects . 3,4 Defect Photographs

17、 _ _- - 5-44 List of Defects . 45,46 Defect Photographs _ _ _ 47-79 Wirebound Wood Boxes: 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-LIST OF DEFECTS NAILED WOOD BOXES WORKMANSHIP AND ASSEMBLY 3 Provided by IHSNot for ResaleNo reproduction or n

18、etworking permitted without license from IHS-,-,-MIL-STD-299 17 lanuary 1957 4 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. ;-TIGHT KNOT. Minor. (Diameter greater than !4 width of part.) Provided by IHSNot for ResaleNo reproduction or networ

19、king permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. 1 -TIGHT KNOT. Minor; (Diameter greater No. 1 -TIGHT KNO

20、T. Permissible. (Diameter less than % width of cleat.) than % width of cleat.) No. 1-KNOT CLUSTER. Minor. (Diameter greater than % width of part.) 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. 1-KNOT CLUSTER. Permissible. (Diameter less than

21、M width of part.) r , Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. 1-KNOT CLUSTER. Minor. (Diameter greater than 45 width of part.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by I

22、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. 2-TIGHT I(N0TS. Minor. (Aggregate diameters more than E width Nok-If these same knots were in a one-piece side th

23、ey would be of part. permissible.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. 3-LOOSE KNOT. Minor. (Larger than %“ diameter.) No. 3-LOOSE KNOT.

24、 Permissible. (Smaller than than 95“. diameter.) No. 3-ENCASED KNOT. Minor. (Larger than %“ diameter.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-277 Bai 99977a13 00671-373 4 No. 3-KNOT HOLE. Minor. (Larger than H“ diameter.) No. J-KNOT

25、HOLE. Permissible. (maller than %“ diameter.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. 4-DECAY. Major. No. 4-DECAY. Major. II Ts 3 g* ., . ,.t - 19 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

26、HS-,-,-No. 4-DECAY. Major. NO. 4-DECAY. Major. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. I-CROS8 GUIN. Minor. No. I-CROS GRAIN. Minor. (lope g

27、reater than 1 in 8.) No. I-CRO GRAIN. Minor. (Slope greater thap 1 in 8.) .- -7- 9 1 ,. Y i 20 r“ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-297 Bl 37777lbb No. 5 -CROSS GRAIN. Minor. (Slope greater than 1 in 8.) No. I-CROSS GRAIN. Permi

28、ssible. (Slope 1 in 8 or less.)Slope illustrated approximately 1 h 8. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. 8-PLXT. Major. (Forms sliver at outside edge.) No. 9-FUEL LENGTH SLITS. Minor. (More. than one unrepaired in a part. Note.- This

29、 would be permissible if one or both of the splits were repaired with corrugated fasteners.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. 9-FULL LENGTH SPLIT. Permissible. (Not more than one, unrepaireci, in a part.) Provided by IHSNot for Res

30、aleNo reproduction or networking permitted without license from IHS-,-,-No, 10-FULL LENGTH SPLITS, Permissible. (Not more than two, repaired, in a part.) I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. No. 11 -PARTIAL SPLITS. Minor. (More than tw

31、o, unrepaired, in a part. Note.-This would be permissible if one or more of the splits were repaired with corrugated fasteners.) No. 11-PARTIAL SPLITS. Permissible. (Not more than two, unrepahd, in a part.) 26 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No. 12-BPLIT. Minor. (Either partial or nUll length in a cover.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-