ARMY MIL-G-50937-1971 GRENADE HAND FRAGMENTATION DELAY M67 AND M33 CONTAINER ASSEMBLY FOR《M67和M33型手榴弹手动迟延存储残片的集装箱装配》.pdf

《ARMY MIL-G-50937-1971 GRENADE HAND FRAGMENTATION DELAY M67 AND M33 CONTAINER ASSEMBLY FOR《M67和M33型手榴弹手动迟延存储残片的集装箱装配》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-G-50937-1971 GRENADE HAND FRAGMENTATION DELAY M67 AND M33 CONTAINER ASSEMBLY FOR《M67和M33型手榴弹手动迟延存储残片的集装箱装配》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、. “ ! 1 MIL-G-50937 (MU) . 16 June 1971 MILITARY SPECIFICATION GRENADE, HAND, FRAGMENTATION, DELAY: M67 and M33 CONTAINER ASSEMBLY FOR 1. SCOPE 1.1 This specification covers the.cover and bottom parts for one type of Container Assembly designated as Container for Grenade, Hand, Fragmentation, Delay:

2、 M67 and M33 (See 6.5). 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bids or request for proposal, forIn a part of this specification to the extent specified herein. SPECIFICATIONS MILITARY ST MIL-A-2550 - Ammunition and Special Weapons, Genera

3、l Specification for MIL-1-45607 - Inspection Equipment, Acquisition, Maintenance and biSpOSitiOn of ANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes (ABC-STD-105) FSC : 1330 “- Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

4、nse from IHS-,-,-. MIL-G-50937 (MU) MIL-STD-109 - Quality Assurance Terms and Definitions MIL-STD-1168 - Lot Numbering of Ammunition MIL-STD-1169 - Packaging, Packing and Marking for Shipment of Inert Ammuni- tion Components MIL-STD-1235 - Single and Multilevel Continu- ous Sampling Procedures and T

5、ables for Inspection by Attributes DRAWINGS U.S . ARMY MUNITIONS COMMAND 9269178 - Container Assembly PUBLICATIONS ARMY ET-9269178 - Equipment Tabulation (Copies of specifications, standards, drawings and publications re- quired by suppliers in connection with specific procurement func- tions should

6、 be obtained from the procuring activity or as directed by the Contracting Officer) . .3 . FU3QUI”ENTS 3.1 Material.-Materials shall be in accordance with the applicable drawings and specifications 3.2 Parts.-The parts shall comply with all requirements specified on Drawing (Dwg.) F-9269178, all ass

7、ociated drawings, and with all requirements specified in applicable specifications. 3.3 Workmanshi .-All parts and assemblies shall be fabricated and finishe * ln a t orough, workmanlike manner. They shall be free of burrs, chips, sharp edges, cracks, unblended radii, surface de- fects, dirt, grease

8、, rust, corrosion products, and other foreign Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-50737 L3 m 7779706 0332555 O WC matter. The cleaning method shall not be injurious to any parts, nor shall the parts be contaminated by the cleaning a

9、gents. All marking and stamping shall be neat a;?d sharply defined. 3.4 Submission of results of contractor-conducted examinations and tests.-The contractor shall forward copies of the results of any of his examinations or tests to the designated address as reiuired by the contract . (See 6.4) . 3.5

10、 First article testing.-This Specification makes proVisions for first article testing. Submission of first article quantity by the contractor shall be as specified in the Contract. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection.-Unless otherwise specified in the contract or purcha

11、se order, the supplier is responsible - far the performance f all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, un

12、less disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Reference. shall be made to MIL-STD-109 to define ter

13、ms used herein. The provisions of MIL-A-2550 shall apply. 4.1.1 Submission of product.-At the time the completed lot of items deliverable under the contract is submitted to the Government for acceptance, the contractor shall supply the following information accompanied by a certificate which attests

14、 that the information provided is correct and applicable to the product being submitted: I a. A statement that the lot complies with al the quality b. Drawing and specification number and date, together c. A statement that all material purchased by the contract0 assurance provisions specified in thi

15、s specification. with identification and date of changes thereto. meets requirements, when such material is controlled by Government or commercial specification referenced in any of the contractual 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI

16、L-G-50737 L3 777770b 0332556 2 =i MIL-G-50937 (MU) document, and that certificates of conformance are on file and available for review. d. Number of items in the lot. e. Date submitted. The certificate shall be signed by a responsible agent of the certifying organization. The initial certificate sub

17、mitted shall be substantiated by evidence of the agents authority to bind his principal. Substantiation of the agents authority will not be required with subsequent certificates unless, during the course of the contract, this authority is vested in another agent of the certifying organization. 4.2 F

18、irst article inspection 4.2.1 Submission.-The contractor shall submit a first article quantity as designated by the Contracting Officer for evaluation in accord.ance with the provisions of 4.2.2 . (See. 6.1) The first article sample shall consist of the following: a. 10 covers bo 10 bottoms. All par

19、ts and completed assemblies submitted shall have been produced by the contractor (or furnished by a supplier) using the same production processes, procedures and equipment as will be used in fulfilling the contract. All parts and materials, including packaging and packing, shall be obtained from the

20、 same sources of supply as will be used in regular production. The sample shall be accompanied by certificates of conformance. A first article . quantity, or portion thereof, as directed by the Contracting Officer, shall also be submitted whenever there is a lapse in production for a period in exces

21、s of 90=days, or whenever a change occurs in manufacturing process, material used, drawing, specification or source of supply as to significantly affect product uniformity as determined by the Government. Prior to submission, the contractor shall inspect the sample to the degree necessary to assure

22、that it conforms to the requirements of the contract and submit a record of this inspection with the sample. A sample containing known defects will not be submitted unless specifically authorized by the Contracting Officer. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

23、ut license from IHS-,-,-MIL-G-50937 (MU) 4.2.2 Inspections to be performed.-Assemblies and components will be subjected by the.Government to any or all the examinations or tests specified in this specification and any or all requirements of the applicable drawings. In addition, any or all of the fol

24、lowing examinations and tests will be performed. 4.2.3 Rejection,-If any assembly or component fails to Comply with any of the applicable requirements, the first article quantity shall be rejected. The Governmentreserves the right to terminate its .inspection upon any. failure of an assembly or comp

25、onent in the sample to comply with any of the stated requirements. In the event of rejection, the Government reserves the right to require the contractor to take corrective action and submit a new first article quantity or portion thereof. Until a first article quantity is ac- cepted, the contractor

26、 is in no way authorized by the Government to resume regular production unless otherwise directed by the Contract- ing Offices, 4.3 Inspection provisions 4.3.1 Lot formation.-The term “inspection lot“ as used in . . ,. this specification is defined as an essentially homogeneous collection of units o

27、f product from which a representative sample is drawn and inspected to determine conformance with . applicable requirements. The sample selected shall represent only that quantity of units from which the sample was drawn. and shall not be construed to represent any prior or subsequent . . quantities

28、 presented for inspection. Homogeneity shall be con- . sidered to exist provided the inspection lot has been produced . -. . by one manufacturer, in one unchanged process, in accordance with the same drawing, same drawing revision, same specificatidn and same specification revision and complies with

29、 the provisions . 1. for submission of product as specified in MIL-STD-105. Changes :-:- to process, specification, or drawing not affecting safety, performance, interchangeability, or storage, as determined by . . the Government, shall not be deemed to alter the homogeneity . . of an inspection lot

30、. All material submitted for inspection in .“-. accordance.with this specification shall comply with the homo- - genei.ty criteria specified herein regardless of the type of sampling procedure which is being applied to- determine confor- mance with requirements. Lot numbering, as required, shall be

31、in accordance with MIL-STD-1168. “ . -. . - : . . . . .- , - .- .P . .:.- , 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-50937 (MU) 4.3.2 “ Examination. -The examinations listed in the following subparagraphs shall be performed on inspecti

32、on lots (See 4.3.1) of the components or assemblies designated in the applicable para- graph headings. Inspection for critical defects (and major defects, when so specified) shall be 100 percent. Sampling plans for major and minor defects shall be in accordance with MIL-STD-105 except that continuou

33、s sampling plans in accordance with MIL-STD-1235 may be used if approved by the Government. Instead of applying the AQLs designated herein to the groups of major and minor defects listed, the contractor may elect to apply AQLs to individual de- fects using an AQL of 0.40 percent for each major defec

34、t and an AQL of 0.65 percent for each minor defect. When this metnod is elected, it shall be applied to al1 of the major and minor defects listed in the applicable subparagraph of this section, except where 100 percent inspection is specified, and be documented as part of the contractors inspection

35、system. Equipment for the performance of the inspections listed shall be necessary in accoz- dance with 4.3.4. 4.3.2.1 Cover, Container See Dwg. 9254953 Categories Defects Method of Critical: None defined Major: AQL 0.40 Percent 101. Flash or feather edge in 102. Flatness at force specified Gage joi

36、nt area Visual Minor : AQL 0.65 Percent 201. Evidence of poor workmanship See 3.3 Visual 4.3.2.2 Bottom, Container See Dwg 9254954 Code No. (See 6.2) 01001 01002 01003 Categories Critical: Major 101. 102. Minor : 201. Defects Method of Inspection None defined AQL O. 40 Percent Flash or feather edge

37、in joint area Visual Flatness at force specified Gage AQL 0.65 Percent Evidence of poor workmanship (See 3.3 Visual Code No. (See 6.2) 02001 02002 02003 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.3.2.3 Container Assembly, See Dwg 9269178 Cat

38、egories Defects Method of Code No. Critical: None defined Major : AQL 0.40 Percent Inspection (See 6.2) 101. Nismatch between cover and 102. Improper fit of insert in bottom, max Gage 03001 bottom Visual 03002 Minor: AQL O. 65 Percent 201. Evidence of poor workmanship See 3.3 Visual 03003 4.3.3 Test

39、ing 4.3.3.1 Dimensional control of plastic.parts.-In place of the normal sampling associated with the Classification of Defects, and with the approval of the Contracting Officer, and after a curing time for the parts has been approved (See Note l), a sample of three (3) parts (as molded) from each c

40、avity may be dimensionally inspected to qualify a new or reworked cavity for use in production or as a control of each cavity during production. curing time for the parts has been reached. The inspection for control of each cavity during production shall be performed on the above quantities from eac

41、h cavity after production of each 5000 parts or at the end of each shift, providing the number of parts produced during that shift is less than 5000 parts. Of the three (3) samples, one (1) sample shall be the last part produced. Parts that fail to comply with dimensional requirements after dimensio

42、nal stability has been attained shall be classed defective. cavity, the- cavity producing the defective part will not be used in production. If any defective parts are found when inspection is performed for control qf the cavity, the cavity producing the defective, part shall be removed from product

43、ion. Further, that portion of production since the last control check shall be returned to the contractor for corrective action. The inspection of the parts shall be performed only when the If any defective parts are found during qualification of the 7 Provided by IHSNot for ResaleNo reproduction or

44、 networking permitted without license from IHS-,-,-MIL-G-50937 (MU) All cavities formerly removed from production because of some fault, mayl after reworking, be returned to production providing they pass the qualification test as above. The contractor may request a change of inspection frequency pr

45、oviding he presents objective evidence to substantiate the request to the Contracting Officer . (NOTE 1) - In establishing a curing time, dimensionally check ten (10) parts from each cavity at periodic intervals (e.g. every 30, 60, etc. mins.) until dimensional stability is attained. the curing time

46、 will be from the time the part comes out cf the moid until dimensional stability is attained. The inspection data used in determining the curing time shall be sent to Picatinny Arsenal, SMUPA-ND3. If any new change in material, cycle time, a reworked cavity, or new cavity is used, a new curing time

47、 shall be established and approved. 4.3.4 Inspection equipnlent . -Equipment Tabulation (ET) number 9269178 and Equipment lists (ELS) referenced thereon identify the inspection equipment required to perform the examinations and tests prescribed in this section. The contractor shall design inspection

48、 equipment in accordance with the instructions in 6.3. Supply and maintenance of the equipment listed on the ELS shall be in accordance with MIL-1-45607. 4.3.4.1 Government rights to documentation.-Inspection equip- ment drawings and lists provided and revised in accordance with the requirements of

49、this specification may be used by DOD activities for design, procurement, manufacture, testing, evaluation, production and receiving inspection, overhaul, shipping, storage, identification of stock, ordering and storage of replacement parts, inspection of items at overhaul, general maintenance of equipment, construction, survey, and whenever inspection equipment drawings are needed. 5. PREPARATION FOR DELIVERY 5.1 I Preserva