ARMY MIL-DTL-3628 105 D-2010 BADGE OCCUPATIONAL CIVIL ENGINEER AIR FORCE《空军网络空间支持初级 高级及大师级职业徽章》.pdf

《ARMY MIL-DTL-3628 105 D-2010 BADGE OCCUPATIONAL CIVIL ENGINEER AIR FORCE《空军网络空间支持初级 高级及大师级职业徽章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 105 D-2010 BADGE OCCUPATIONAL CIVIL ENGINEER AIR FORCE《空军网络空间支持初级 高级及大师级职业徽章》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 2 FSC 8455 DETAIL SPECIFICATION SHEET BADGE, OCCUPATIONAL, CIVIL ENGINEER, AIR FORCE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification

2、 sheet and the latest issue of MIL-DTL-3628. BASIC SENIOR MASTER DASH NO. -1: Basic, Regular Size -4: Basic, Mid Size -2: Senior, Regular Size -5: Senior, Mid Size -3: Master, Regular Size -6: Master, Mid Size MATERIAL: Not less than 85/15 Rich-Low Brass or Nickel Silver FINISH: Nickel Plated (Brass

3、 only), Mirror-like Polished and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 16. DIMENSIONS: HEIGHT (overall): -1: 3/4 inch (REF) -2: 1-1/16 inches (REF) -3: 1-1/16 inches (REF) -4: 9/16 inch (REF) -5: 57/64 inch (REF) -6: 57/64 inch (REF) INCH-POUND MIL-DTL-3628/105D 19 Ma

4、rch 2010 SUPERSEDING MIL-DTL-3628/105C 11 May 2005 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/105D Page 2 of 2 WIDTH (overall): -1 to -3: 1-5/8 inches (REF) -4 to -6: 1-7/32 inches (REF) THICKNESS (at thickest point): -1 to -3: 0.10

5、5 0.005 inch -4 to -6: 0.090 0.005 inch NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. Piercing shall be as indicated for all the regular and mid size badges except that the mid size master badge (-6) shall not be pierced in the area of the wre

6、ath and star. 3. Attaching device shall be prong and clutch type. Two prongs shall be located at each intersection of the horizontal center line of the badge and the center of each side of the wreath. CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to in

7、dicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irre

8、spective of the marginal notations and relationship to the last previous issue. Custodian: Preparing activity: Army - IH Army - IH Air Force - 11 Review activities: (Project No. 8455-2010-112) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-