ARMY MIL-DTL-14639 31 B-2010 INSIGNIA RANK CAPTAIN ARMY AND AIR FORCE《陆军和空军上尉军衔徽章》.pdf

《ARMY MIL-DTL-14639 31 B-2010 INSIGNIA RANK CAPTAIN ARMY AND AIR FORCE《陆军和空军上尉军衔徽章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-14639 31 B-2010 INSIGNIA RANK CAPTAIN ARMY AND AIR FORCE《陆军和空军上尉军衔徽章》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 2 FSC 8455 DETAIL SPECIFICATION SHEET INSIGNIA, RANK, CAPTAIN, ARMY AND AIR FORCE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sh

2、eet and the latest issue of MIL-DTL-14639. DASH NO. -1: Regular Size -2: Miniature Size (AF) -3: Regular Size, Subdued MATERIAL: -1,-2: Red Brass or Nickel Silver -3: Red Brass or Zinc Aluminum DIMENSIONS: HEIGHT (overall): -1,-3: 1 inch (REF) -2: 3/4 inch (REF) WIDTH (overall): -1,-3: 1 inch (REF)

3、-2: 3/4 inch (REF) THICKNESS (overall): -1,-3: 0.065 inch + 0.005 inch -2: 0.050 inch + 0.005 inch INCH-POUND MIL-DTL-14639/31B 5 February 2010 SUPERSEDING MIL-DTL-14639/31A 30 January 1998 PIERCED Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-

4、DTL-14639/31B Page 2 of 2 FINISH: -1,-2: Nickel Plated, Mirror-like Polished and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 16. -3: Dull Flat Black and shall match TIOH Metal Finish Chip Number 21. NOTES: 1. The term (REF) refers to the measurements taken from the Governme

5、nt furnished hub or die. 2. Attaching device shall be prong and clutch type. One prong shall be centered on the back of each bar. 3. Miniature insignia shall be dapped in the horizontal plane along a 2-1/2 inches + 1/64 inch radius. The dap for regular size insignia is built into the Government furn

6、ished hub. 4. Dash No. -1 and -2 may be rhodium plated with a mirror-like polished finish at the option of the manufacturer. 5. A forcer may be used to bring up the design for Dash No. -1 and -3. There shall be a thickness of 0.065 inch + 0.005 inch from the edge and high point of the bevel. CHANGES

7、 FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors

8、are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodian: Preparing activity: Army - IH Army - IH Air Force - 11 Review activities: (Project No. 8455-2010-069) Air Force - 99

9、DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-