ARMY MIL-C-606 F-1987 CLOTH BANNER RAYON《人丝旗布》.pdf

《ARMY MIL-C-606 F-1987 CLOTH BANNER RAYON《人丝旗布》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-606 F-1987 CLOTH BANNER RAYON《人丝旗布》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-60bF 3 E 9979906 0371355 O W /Lt -37-53 MIL-C-606F 18 December 1987 SUPERSEDING 5 May 1970 MIL-C-606E MILITARY SPECIFICATION CLOTH, BANNER, RAYON This specification is approved for use by all Departments and Agencies of the Department of Defense. 1, SCOPE -. -. 1.1 Scope. This document covers

2、one type of rayon banner cloth. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Documents. The following documents form a part of this document to the extent specified herein. documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DOD

3、ISSI and supplement thereto, cited in the solicitation. Unless otherwise specified, the issues of these SPECIFICATIONS FEDERAL PPP-P-1133 - Packaging of Synthetic Fiber Fabrics STANDARDS FEDERAL FED-STD-191 - Textile Test Methods Beneficial comments (recommendations, additions, deletions) and any pe

4、rtinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self- addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or

5、 by letter. AMSC N/A FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS / PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - MIL-C-b0bF 3 W 999990b 037135b 2 W MIL-C-606F MILITARY

6、MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes 2.1.2 Other Government documents. The following other Government documents Unless otherwise form a part of this document to the extent speci.fied herein. specified, the issues shall be those in effect on the date of the solici

7、tation. Rules and Regulations Under the Textile Fiber Products Identification Act (Application for copies should be addressed to the Federal Trade Commission, 4 Pennsylvania Avenue at Sixth Street, N.W., Washington, DC 20580.) J. .* (Copies of documents required by contractors in connection with spe

8、cific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) * 2.2 Other publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are D

9、OD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the date of the solicitation. AMERICAN ASSOCIATION OF TEXTIL

10、E CHEMISTS AND COLORISTS ( AATCC Chromatic Transference Scale (Application for copies should be addressed to the American Association of Textile Chemists and Colorists, AATCC National Headquarters, P.O. Box 12215, Research Triangle Park, NC 27709-2215.) COLOR ASSOCIATION OF THE UNITED STATES Standar

11、d Color Reference of America (Application for copies should be addressed to the Color Association of the United States, Inc., 343 Lexington Avenue, New York, NY 10016). (Technical society and technical association documents are generally available for reference from libraries. They are also distribu

12、ted among technical groups and using Federal agencies.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-h0bF 3 W 777790b 0371357 4 E MIL-C-606F 2.3 Order of precedence. In the event of a conflict between the text of this document and the refe

13、rences cited herein, the text of this document shall take precedence. Nothing in this document, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Standard sample. The dyed and finished cloth shall match the standard sample for

14、 shade and appearance and shall be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced (see 6.3). 3.2 Material. 3.2.1 Rayon. The rayon shall be multifilament cuprammonium rayon. 3.2.1.1 Yarn. The yarn shall be 2-ply for both the

15、 warp and filling. * 3.3 Color. The color shall be as specified (see 6.2). Shade designations and cable numbers (see 6.3.1) are from the Color Association of the United States (see 2.2 and 6.4). The dyeing shall be accomplished on the yarns prior to weaving, using vats, napthols, or cellulose reacti

16、ve dyes as appropriate (see 6.3.1). The use of solution dyed cuprammonium yarns in lieu of the above dye types is permitted provided that the hue and brilliancy of the shade can be achieved. Care should be exercised during dyeing to achieve a degree of penetration of the yarns such that the finished

17、 cloth shall show no more barre than is shown by the standard sample. * 3.3-1 Matching. The color of the finished cloth shall match the standard sample when viewed under filtered tungsten lamps that approximate artificial daylight and that have a correlated color temperature of 7500 2 200K, with ill

18、umination of 100 2 20 foot candles and shall be a good match to the standard sample under incandescent lamplight at 2300 2 200K. * 3.3.2 Colorfastness. The finished cloth shall show fastness to wet drycleaning and light equal to or better than the standard sample or equal to or better than a rating

19、of llgood.ll The finished cloth shall show fastness to crocking equal to or better than the standard sample or shall have an AATCC Chromatic Transference Scale rating of not lower than 7.5, except that for napthol dyed cloth shall have an AATCC Chromatic Transference Scale rating of not lower than 6

20、.5. Testing shall be as specified in 43. 3.4 Physical requirements. The dyed and finished cloth shall conform to the requirements as specified in table I when tested as specified in 4.3. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-60bF 3

21、W 779790b 0371358 b W MIL-C-606F TABLE I. Physical requirements Weight per Breaking strength, square yard, Yarns per inch (minimum) pounds (minimum) ounces (minimum) Warp Fil 1 ing Warp Fil ling Weave 5.0 282 2 Right - 94 125 50 2 twill 3.4.1 Width. The width of the cloth shall be as specified (see

22、6.2) and shall be the minimum acceptable width inclusive of selvages when fly shuttle looms are used, and exclusive of selvages and fringe when shuttleless looms are used. Tuck-in selvages shall not be permitted. 3.5 Finish. The cloth shall have a hand and drape equal to or better than the standard

23、sample. cloth is prohibited, unless otherwise specifically approved and authorized by the contracting officer (see 4.3). The use of resin finishes to impart stiffness to the 3.5.1 pH. The pH value of the water extract of the finished cloth shall be no less than 5.5 nor more than 8.5 when tested as s

24、pecified in 4.3, 3.6 Length and put-up. Unless otherwise specified (see 6.21, the finished cloth shall be furnished in continuous lengths, each not less than 50 yards. Each length shall be put up in a full width roll as specified in 5.1.1. 3.7 Fiber identification. Each roll of cloth shall be labele

25、d and ticketed for fiber content in accordance with the Textile Fiber Products Identification Act. 3.8 Workmanship. The finished cloth shall conform to the quality of product established by this document and the occurrence of defects shall not exceed the applicable acceptable quality levels. 4 -.*,

26、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I I t I i ! I I t ! l i I I t 1. t I t 1 I i 1 MIL-C-606F 3 7799706 0373357 B MIL-C-606F 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or

27、purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements sp

28、ecified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this document where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. Al

29、l items must meet all requirements of sections 3 and 5. The inspection set forth in this document shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirement in the document shall not relieve the contractor of the responsibility of a

30、ssuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of def

31、ective material. 4.1.2 Certificates of compliance. When certificates of compliance are submitted, the Government reserves the right to inspect such items to determine the validity of the certification. 4.2 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be p

32、erformed in accordance with MIL-STD-105. 4.2.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this document or applica

33、ble purchase document. 4.2.2 End item examination. * 4.2.2.1 One hundred percent inspection. The entire yardage of each roll of cloth shall be inspected on both sides. All defects listed below that are clearly noticeable at normal inspection distance (3 feet) shall be scored as a defect. All defects

34、 found shall be counted except where two or more defects appear within 1/2 linear yard of the cloth, in which case only one defect shall be counted. A continuous defect shall be counted as one defect for each warpwise yard 01“ fraction thereof in which it occurs. Each defect shall be marked with a r

35、ed string, 1 inch to 1 1/2 inches long, sewn into the selvage opposite the defect. A deduction of 1/4 yard for each strung defect shall be 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b0bF 3 7779706 0373360 4 W MIL-C-606F subtracted from t

36、he gross length of the roll to determine the net yards to be entered on the roll ticket. yardage basis. Acceptance by the Government shall be on a net Cut, hole, or tear Broken or missing yarn Smash Float, mispick, harness skip, or other misweave Hitchback, stripback Open or thin place, crack (warp

37、or filling) Loose, slack, or tight yarns Reed mark, wrong draw Abrasion mark, bruise, tender or weak spot Crease or wrinkle, embedded Selvage cut, torn, folded, rolled, slack, tight or Filling bar, coarse filling, or mixed filling Spot, stain, streak, or dirty yarn Foreign matter 4.2.2.2 Overall exa

38、mination. The cloth shall be examined for extensive, Knot , kink scalloped with identations more than 1/2 inch general, or overall defects. shall be rejected. Any roll containing any of the following defects Finish not equal to nor better than standard Offshade, or uneven throughout piece Overall un

39、cleanness or soiled Baggy, ridgy, wavy, or unevenly woven Width not within established tolerances Net length less than indicated on the ticket Incorrect deduction for defects strung by the supplier, Fiber identification marking omitted Mottled, Cloudy, streaky, Or barre as indicated on piece ticket

40、4.2.3 Government verification. Verification examination shall be on a sampling basis. 4.2.3.1 Yard-by-yard examination. The finished cloth shall be examined for the defects listed in 4.2.2.1. Any defect not strung and visible at normal inspection distance (3 feet) and not within 1/2 linear yard of a

41、 strung defect shall be scored. sample unit shall be one linear yard. the acceptable quality level (AQL) shall be 1.0 unstrung defects per 100 linear yards, If the number of,unstrung defects in the sample equals or exceeds the reject number for the sample size and foregoing AQL, the entire lot shall

42、 be returned to the contractor for screening and stringing of all unstrung defects. The lot shall be expressed in units of one yard each. The The inspection level shall be III and 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-60bF 83 I 9979

43、70b 03713bL b MIL-C-606F I I r 1 4.2.3.2 Overall examination. The sample size for overall examination shall be the number of rolls selected for the yard-by-yard examination (see 4.2.3*1). the defects listed in 4.2.2.2. The lot shall be unacceptable if one or more rolls contain any of 4.2.4 Shade exa

44、mination. Each roll in the lot shall be examined visually for shade match (see 3.3.1). the requirements for shade match. The sample unit for this examination shall be a 4-inch by 20-inch swatch of the cloth. each roll in the lot. A roll shall be unacceptable if it fails to meet A sample unit shall b

45、e drawn from 4.3 End item testing. The cloth shall be tested for the characteristics listed in table III. The methods of testing specified in FED-STD-191 wherever applicable, and as listed in table III shall be followed. The physical and chemical values specified in section 3, except where otherwise

46、 specified, apply to the results of the determinations made on a sample unit for test purposes as specified in the applicable test method. contain the individual values utilized in expressing the final result. The sample unit shall be 1 1/2 continuous yards full width of the finished cloth. The lot

47、size shall be expressed in units of one yard. The lot shall be unacceptable if one or more sample units fail to meet any requirement specified. The sample size shall be in accordance with the following: All test reports shall Lot size (Pards) Sample size (sample units) 800 or less 2 801 up to and in

48、cluding 22,000 3 22,001 and over 5 TABLE II. End item tests Characteristic Requirement reference Test method Rayon fiber iden tif ica ti on blultifilament Yarn ply Warp Filling 3.2.1 3.2.1 3.2.1.1 3.2.1.1 1/ - Visual 2/ - Visual 2/ Visua 2/ - 7 I Provided by IHSNot for ResaleNo reproduction or netwo

49、rking permitted without license from IHS-,-,-MIL-C-bObF 3 m 9799906 0373362 8 - MIL-C-606F TABLE II. End item tests - Continued Characteristic Requirement reference Test method Colorfastness to: Light Crocking Wet drycleaning Weight Yarns per inch: Warp Filling Breaking strength: Warp Fil 1 ing Weave Finish PH 3.4 3.4 3.4 3.4 3.4 3.5 3.5.1 5660 5651 - 3/ 5622 504 1 5050 5050 51 O0 51 O0 Visual 2/ - 4/ 281 1 - I/ Unless otherw