ARMY FF-S-611 A-1972 SPIKES TRACK SQUARE-SHANK《鞋钉方柄轨道》.pdf

《ARMY FF-S-611 A-1972 SPIKES TRACK SQUARE-SHANK《鞋钉方柄轨道》.pdf》由会员分享，可在线阅读，更多相关《ARMY FF-S-611 A-1972 SPIKES TRACK SQUARE-SHANK《鞋钉方柄轨道》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、FF- S- 61 lA June 26, 1972 SUPERSEDING Fed. Spec. FF-S-611 April 26, 1954 FEDERAL SPECIFICATION SPIKES, TRACK, SQUARE-SHANK This specification was approved by the Comissioner , Federal Supply Services, General Services Administration, for use of all Federal Agencies. 1. SCOPE AND CLASSIFICATION 1.1

2、Scope. This specification covers square-shank, cut-steel track spikes. 1.2 Ciassification. 1.2.1 Grades. Spikes shall be of the following grades, as specified (see 6.2). Grade A - High-carbon steel. Grade B - Soft steel. 1.2.2 Sizes. Spikes shall be of the sizes as specified, (see Table IV and 6.2).

3、 2. APPLICABLF: DOCUMENTS 2.1 The following documents of the.issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. Federal Specifications NN-K-231 - Kegs: Wood, Slack PPP-D-705 - Drum: Metal Shipping, Steel (Over 12

4、and Under 55 Gallon) FSC 2250 - -:Y Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF- S- 6 11A Federal Standards Fed. Test Method Std. No. 151 - Metals: Test Methods (Activities outside the Federal Government may obtain copies of Federal Specificat

5、ions and Standards as outlined under General Information in the Index of Federal Specifications and Standards and at the prices indicated in the Index. The Index, which includes cumulative monthly supplements as issued, is for sale on a subscription basis by the Super- intendent of Documents, U.S. G

6、overnment Printing Office, Washington, D.C. 20402. Single copies of this specification and other product specifications required by activities outside the Federal Government for bidding purposes are available without charge at the General Services Administrat5on Regional Offices in Boston, New York,

7、 Washington, D.C., Atlanta, Chicago, Kansas City, Mo., Dallas, Denver, San Francisco, Los Angeles and Seattle, Washington. Federal Government activities may obtain copies of Federal Specifications and Standards and the Index of Federal Specifications and Standards from established distribution point

8、s in their agencies.) Military Specifications: MIL-D-6054 - Drum, Metal-Shipping and Storage MIL-D-6055 - Drums, Metal, Reusable Shipping and Storage (Cap. From 88 to 510 Cubic Inches) Military Standards: MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking

9、 or Shipment and Storage (Copies of specifications, standards, drawings and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publications. The following document

10、s form a part of this specification to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply. Uniform Classification Committee, Agent: Uniform Freight Classification (Application for copies should be addressed

11、to the Uniform Classification Committee, Tariff Publishing Officer, Room 202 Union Station, 516 W. Jackson Blvd., Chicago, Ill. 60606.) . , . L -. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-(Application for copies should be addressed to Nation

12、al Motor Freight Traffic Association, Inc. , 1616 P. Street, NeW. , Washington, D.C. 20036.) 3. REQUIREMENTS 3.1 Material. Spikes shall be of steel manufactured by the open- hearth, acid-bessemer, electric-furnace or basic-oxygen processes. The chemical composition shall be as specified in Table I,

13、3.1.1 Chemical Analysis. A chemical Analysis of the steel used in the spikes shall be furnished by the manufacturer and shall show the carbon content and the copper content when copper-bearing steel is specified. Table I - Chemical Composition Carbon Content % Min Copper* Material Coiient % Min Acid

14、-Bessemer Other I Grade A Grade B .20 .O6 .30 .20 12 .20 - - When copper-bearing steel is specified (see 6.2). 3.2 Tensile properties. The manufacturer may, at his option, sub- stitute tension tests for the chemical analysis specified in 3.1.1. sile properties of the spikes shall be as specified in

15、Table II. Ten- Table II - Tensile Properties Tens i le Yield Elongation PSI Min PSI Min % Min Mat er ia 1 S t r eng th Point: in 2 inches t I I I I I Grade A 70 , O00 35,000 Grade B 55,000 27 , 500 25 25 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

16、,-,-FF-S-6LLA 22 mm97L1 0033252 7 a I - - FF-S- 611A 3.3 Bending properties. 3.3.1 Grade A. 3.3.1.1 Stem (bodyl. The body of a finished spike shall withstand being bent cold through 120 around a pin having a diameter not greater than the thickness of the spike, without cracking on the outside of the

17、 bent p Ort ion. 3.3.1.2 Head. The head of a finished spike shall withstand being. bent backwards to an angle of 55 with the line of the face of the spike, without cracking on the outside of the bent portion. 3.3.2 Grade B. 3.3.2.1 Stem (bodyl. The body of a finished spike shall withstand being bent

18、 cold through 180, flat on itself, without cracking on the outside of the bent portion. 3.3.2.2 Head, The head of a finished spike shall withstand being bent backward to the line of the face of the spike, without cracking on the outside of the bent portion and without showing evidence of forging lap

19、s on the surface of the bent portion. 3.4 Dimensions. Head shape and dimensions for spikes 5 inches or less in length shall be as commercially manufactured, unless otherwise specified (see 6.2 and Table IV). Spikes more than 5 inches in length shall conform to figures 1, 2 and 3, as applicable, as s

20、pecified in Table III. specified. Tolerances shall be All dimensions are in inches, unless otherwise Table II - Tolerances Cross-section +1/32 -1164 Head +3 /32 - 1/32 Length, under head to point +1/8 -118 Angle, under side of head +1 deg. -1 deg. 3.5 Marking. The heads of all spikes shall carry bra

21、nd marks or letters so that the manufacturer may be readily determined. 3.5.1 High-carbon steel (grade A) spikes shall be marked with the letters “HC“ . 3.5.2 Spikes specified to be of copper-bearing steel shall be marked Provided by IHSNot for ResaleNo reproduction or networking permitted without l

22、icense from IHS-,-,-4 4 400 =li rolm 4 IrJp - - +a 1 6. UNDER HEAD (FOR OPTIONAL DESIGN SEE FIGURE 3) FIGURE 2. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF-C - 611A 9 6 2 5 8 I O W L Q- W Z 3 (D a ti -IN 8 uj I; 5 g X 6. (OPTION FOR FIGURE 2

23、.) ZX 5 62 I FIGURE 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF-S-61 I A Table IV - Sizes and Weights Size Cross Section 114 114 114 114 114 114 5/16 5/16 5/16 5/16 5/16 5/16 5/16 318 318 3 /8 3 I8 318 318 3 I8 Length Under Head 1- 114 1- 1

24、12 2 2-114 2i1/2 3 1- 112 2 2-1/4 2-112 3 3- 112 4 2 2-114 2-112 3 3- 112 4 4- 1/2 Nomina 1 Numb er of Spikes Per 200- Pounds 6,800 5,735 4,350 3,850 3 , 500 3,070 3,440 2,875 2,760 2,460 2,165 1,970 1,775 1,720 1 , 560 1,365 1 , 880 1,210 1,080 975 Size Cross Section 318 7/16 7/16 7/16 7/16 7/16 7/

25、16 112 112 112 112 1 /2 1/2 9 / 16* 9 / 16* 9/16 5/g*a 5/8* 518 518 Length Under Head 5 2-112 3 3-112 4 4- 112 5 2-112 3 3- 112 4 4- 112 5- 4- 112 5 5-112 4- 112 5 6 6- 1/2 Nominal Numb er of Spikes Per 200- Pounds 885 1 , 105 1,055 87 5 775 7 10 650 890 7 80 69 O 59 5 545 515 410 365 5.33 5 3 10 2

26、85 *245 *230 NUTE: The number of finished spikes varies as much as 2 15%, except for those marked with an (Jc) , which vary about 2 5%. * Heads are similar to the designs shown in figures 1 and 2. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF-

27、S-bLLA 22 7779774 00L325b b FF-S-611 A 3.6 Workaanshtp Finished spikes shall be smooth and straight with well-formed heads, sharp points, and be free from :licks, checks, cracks and ragged edges. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the con

28、tract or purchase order, the supplier is responsible for the per- formance of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requirements spec

29、ified herein, unless disapproved by the Government. “he Government reserves the right to perform any of the inspections set forth inthe specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 E. Unless otherwise specified (see

30、 6.2), a lot shall consist of not more than 10 tons of spikes of the same heat and size manufactured by the same process and offered for acceptance at any one time, specified (see 6.2), a number of lots may be offered simultaneously for acceptance. When 4.3 Sampling. 4.3.1 Sampling for examination.

31、A random sample of spikes shall be taken from each lot in accordance with MIL-STD-105, Inspection Level S-1. The Acceptable Quality Level (AQL) shall be 6.5 percent defective. 4.3.2 Sampling for chemical analysis. 4.3.2.1 Melt known. Samples shall consist of one test ingot cast during the pouring of

32、 each heat of steel. 4.3.2.2 Melt unknown. Sample drillings shall be taken from three sample spikes selected at random from each 10 tan lot of spikes offered for acceptance. 4.3.3 Sampling for tension test. When the manufacturer requests to conduct a tension test instead of chemical analysis, one sa

33、mple spike shall be selected from each 10 ton lot or fraction thereof for the tension test. 4.3.4 Sampling for bend test. One sample spike shall be selected from each 5 tons or fraction thereof in a lot for the stem (body) bend test and another sample spike for the head bend test. 4.4 Examination. S

34、amples selected as specified in 4.3.1 shall be subjected to visual inspection for marking (3,5) and workmanship (3.6), and to measurements (using standard inspection equipment) for dimensional requirements (3.4) o 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

35、 from IHS-,-,-4.5 Tests. 4.5.1 Chemical analysis. Samples selected as specified in 4.3.2 shall be subjected to a chemical analysis to verify conformance to 3.1.1 and Table I. The analysis shall be conducted in accordance with Methods 111.2 or 112.2 of Fed. Test Method Std. No. 151. In case of disput

36、e, Method 111.2 shall be the basis for acceptance. 4.5.2 Tension test. When requested by the manufacturer, samples selected as specified in 4.3.3 shall be subjected to a tension test to verify conformance to 3.2 and Table II. 4.5.3 Bend test. The bend test may be made by pressure or hammer blows. 4.

37、5.3.1 Stem (body). Samples selected as specified in 4.3.4 shall be subjected to a bend test to verify conformance with 3.3.1.1 and 3.3.2.1, as app licab le. 4.5.3.2 Head. Samples selected as specified in 4.3.4 shall be subjected to a bend test to verify conformance with 3.3.1.2 and 3.3.2.2, as appli

38、cable. 4.6 Rejection, re-examination and retest 4.6.1 Reiection. Failure of any sample to meet the chemical or mechanical requirements of this specification shall be cause for the rejection of the lot. 4.6.2 Re-examination. A lot rejected for failing to meet the marking, workmanship or dimensional r

39、equirements may be resubmitted for examination provided the manufacturer has examined all the spikes in the lot for the defect noted and has removed and replaced, reworked or repaired all non- conforming spikes. 4.6.3 Retest. A lot rejected for failing to meet any test require- ments may be resubmit

40、ted for retest in accordance with the requirements of MIL- STD- 105 o 5. PWPARATION FOR DELIVERY 5.1 Packing. Packing shall be level A or C, as specified (see 6.2). 5.1.1 Level A. Spikes separated by grade and size shall be packed in kegs conforming to NN-K-231 or steel drums conforming to MIL-D-605

41、4, Class S .of MIL-D-6055, PPP-D-705 or equal. Each container shall contain approximately 200 pounds of the nominal number of finished spikes listed in Table IV. 5.1.2 Level C. Approximately 200 pounds of spikes separated by grade and size, and consisting of the nominal number listed in Table IV, sh

42、all be packed to afford adequate protection against damage during direct shipment 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF-S-6LLA 22 E 9979974 0033258 T = FF-S-61 I A from supply source to first receiving activity at the lowest applicable

43、 rate. rules or National Motor Freight Classification rules. Containers and packing shall comply with Uniform Freight; Classification 5.2 Marking. Each container shall be marked in accordance with MIL-STD-129 and tagged as follows: (a) Name of the item. (b) (c) Size: cross-sectional size and length.

44、 (d) (e) Quantity contained (by weight). (f) Contract or order number. (g) (h) 6, NOTES Grade, and if copper-bearing steel (CU), Federal Specification Number and/or Federal Stock Number. Manufacturers name or trade mark. Contractors name (if not the same as manufacturers), 6.1 Intended use. The larg

45、er spikes covered by this specification are intended to hold down railroad rails to the tie and tie plate. spikes are intended for general purpose use wherever an offset head is required. Smaller 6.2 Ordering data. Purchasers should exercise any desired options offered herein, and procurement docume

46、nts should specify the following: (a) Title, number and date of this specification. (b) Grade, and if copper-bearing steel is required, not specified, either grade may. be furnished (1.2*1). (c) Size: cross-section and length (1.2.2 and Table IV). (d) Dimensions, if other than specified (3.4). (e) L

47、ot size and number, if other than specified (4.2). (f) Level of packing required (see 5.1) o If grade is Military Custodians: Amy - WC Navy - YD Air Force - 84 Reviewer Activities: Amy - ME Navy - None Air Force - None User Activities: Navy - None Air Force - None by - CE bepasing Activity: Civil Ag

48、encies Interest: Army - wc GSA Orders for this publication are to be placed with the General Services Administration, acting as an agent for the Superintendent of Documents. See section 2 of this specification to obtain extra copies and other documents referenced herein. Price 15 cents each. t U. S. GOVERNhENT PRINTING OFFICE : 1972 O - 514-169 (26) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-