ARMY A-A-56012-1989 HANDLE FOLDING FEMALE 90 DEG DETENT《90度可折叠女士制动器手柄》.pdf

《ARMY A-A-56012-1989 HANDLE FOLDING FEMALE 90 DEG DETENT《90度可折叠女士制动器手柄》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-56012-1989 HANDLE FOLDING FEMALE 90 DEG DETENT《90度可折叠女士制动器手柄》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、16- August 1989 COMNERCIAL ITEM DESCI HANDLE, FOLDING, FEMALE The General Services Admini stration use of this commercial item descript Abstract. This Commercial Item Description covers one type of handle, folding, female 90“ detent. IPTION 90“ DETENT has authorized the on. 1- D I- TABLE I. DASH NUM

2、BERS L T FIGURE 2 - Beneficial comments, recommendations, additions, deletions, clarifications, etc., and data which may improve this document should be sent to: Commander, U.S. Army Missile Command, ATTN: AMSMI-RD-SE-TD-ST, Redstone Arsenal, AL 35898-5270. DISTRIBUTION STATEMENT A. Approved for pub

3、lic release; distribution? is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L, Handles shall be detent for two ,wsitions 90“ apart as shown in figure 2, 2, Material. Brass, composition 22, 1/2 hard, per QQ-B-626. “0“ Ring Iraterial per M

4、IL-P-25732. J. Proeective finish. Nickel plate ,oer QQ-N-290, Class 1, Type 6 (KC). 4. Pin, Hardened Ground Production Wei, .L25 x .281 steel, Lper ANSI Bld.8.2-1978, chromium plate per QQ-C-329 Class 1, Typs II (Satin Finish) (see figure 2 above), - 3. gardmre. 2 “O“ Rings and. the roateria1 as sta

5、te6 above. . The contractor shall certify and mintain the product ofzered meets the salient characteristics of this CmErcial Item Description, and that the prdict conform to the producers em drawings, specifications, standards, and quality assurance practices. The Governmalt reserves the right to re

6、quire proof sf such conformnc2 prior to first delivery and thereafter as my be otherwise provided for under the provisions of the contract, “etr!ic products, Products manufactured to mtric dinensions will !x considered on an equal basis with those manufactured using inch-wund units, provided they fa

7、ll within specified tolerances using conversion tables contained in the latest revision of Federal Standard No. 376, and all other requirawnts o this Conmercial Item Description are met. If a product is manufactured to wtric dimensions and those ddnsions exceed the tolerances specified in the inch/p

8、ound units, a request should be mde to the contracting officer to determine if the product is acceptable -quirementa. The offeror/contractor is encouraged to use recover& materials in accordance with Public Law 94-580 to the maxilnlun extent practicable. Preservation, packaging, packing, labzlinq, a

9、nd Lmrkinq. Preservation, scicaging, gacking, labeling, and marking shall be a s,oecif ied in the contract or order, CID bas4 part identification number. The following part identification numbering procedure is for Govermwnt purpses and does not constitute a requirerui3nt for the contractor, L“56012

10、“l Designates dash nlunber (see table I) CID Nuher Designates a CID Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-56012 53 7777774 0002158 b W - _- ,S- - - .* A-A-56012 Notes. 1. Size and quantity required shall be as specified in the contract

11、or order (see table 1). 2. FED-STO-376 is available from tQe Naval Publications and Forms Center, 5801 Tabor Avenue, Phi ladelphia, PA 19120-5093. Custodian: Army - MI Prepariiny Activity: Army - MI Project 90. 5340-A047 3 FSC 5340 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-