SAE AS 4573B-2001 Hose Assembly PTFE Para-Aramid Reinforced Standard Duty 3000 psi 275 degrees F Titanium Fittings Flareless 90 degrees to 90 degrees《(R)FSC 4720 90度对90度非扩口钛接头3000 .pdf

《SAE AS 4573B-2001 Hose Assembly PTFE Para-Aramid Reinforced Standard Duty 3000 psi 275 degrees F Titanium Fittings Flareless 90 degrees to 90 degrees《(R)FSC 4720 90度对90度非扩口钛接头3000 .pdf》由会员分享，可在线阅读，更多相关《SAE AS 4573B-2001 Hose Assembly PTFE Para-Aramid Reinforced Standard Duty 3000 psi 275 degrees F Titanium Fittings Flareless 90 degrees to 90 degrees《(R)FSC 4720 90度对90度非扩口钛接头3000 .pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Copyright 2004 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, orotherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT

2、ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.orgSAE Technical Standards Board Rules providethat: “This report is published by SAE to advancethe state oftechnical and engineering sciences.Theuse

3、ofthis reportisentirelyvoluntary, andits applicabilityand suitabilityfor any particularuse,including any patentinfringement arising therefrom,isthe sole responsibility of the user.”SAE reviews each technical reportatleastevery five years atwhich timeitmay bereaffirmed,revised, or cancelled.SAE invit

4、es yourwritten comments and suggestions.SHEET 1 OF 4AS4573REV.BTHIRD ANGLE PROJECTIONAEROSPACE STANDARDAS4573REV. BISSUED 1992-06 REVISED 2001-01 REAFFIRMED 2004-06(R) HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED,STANDARD DUTY, 3000 PSI, 275 F, TITANIUMFITTINGS, FLARELESS, 90 TO 90CUSTODIAN: SAE G-3/

5、G-3D PROCUREMENT SPECIFICATION: AS1975 /2/FEDERAL SUPPLY CLASS 4720FIGURE 1 - HOSE ASSEMBLY, 90 ELBOW TO 90 ELBOWFIGURE 2 - ELBOWS ORIENTATIONCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-(R) HOSE AS

6、SEMBLY, PTFE, PARA-ARAMID REINFORCED,STANDARD DUTY, 3000 PSI, 275 F, TITANIUMFITTINGS, FLARELESS, 90 TO 90AEROSPACE STANDARDAS4573SHEET 2 OF 4AS4573REV.BREV. BTABLE 1 - ASSEMBLY DIMENSIONSHOSEASSEMBLYNO. & SIZECODEHOSESIZE(REF)THREAD TPER AS8879(REF)HOSEIDMINAMAXBGAGEBASICD(REF)E /8/MAXWITHOUTSLEEVI

7、NGF HEX(REF)GMINGMAXSPHERICALBALL SIZEFORDETERMININGMINIMUMHOSEASSEMBLY ID /7/INAS4573E .250 .4375-20UNJF-3B .212 1.880 .2930 .16 .69 .56 .645 .790 .115AS4573G .375 .5625-18UNJF-3B .298 2.180 .4120 .16 .80 .69 .715 .840 .204AS4573H .500 .7500-16UNJF-3B .391 2.530 .5600 .19 .97 .88 .845 .970 .289AS45

8、73J .625 .8750-14UNJF-3B .485 3.375 .6730 .20 1.15 1.00 1.065 1.210 .349AS4573K .750 1.0625-12UNJ-3B .602 3.940 .8100 .23 1.38 1.25 1.275 1.400 .434AS4573M 1.000 1.3125-12UNJ-3B .852 4.485 1.0620 .30 1.66 1.50 1.500 1.625 .646AS4573N 1.250 1.5625-12UNJ-3B 1.100 5.225 1.3160 .04 2.33 1.81 1.700 1.825

9、 .816AS4573P 1.500 TBD TBD TBD TBD TBD TBD TBD TBD TBD TBDTABLE 2 - HOSE OR SLEEVE OUTSIDE DIAMETERSLEEVECODE SLEEVE MATERIALTEMPLIMITF TOLERANCEHOSESIZE/10/.250HOSESIZE/10/.375HOSESIZE/10/.500HOSESIZE/10/.625HOSESIZE/10/.750HOSESIZE/10/1.000HOSESIZE/10/1.250HOSESIZE/10/1.500- BRAIDED HOSE ONLY PERA

10、S1975275 MAXMIN.465.405.555.495.710.650.920.8501.075.9951.3651.2851.6601.580TBDTBDA FIRESLEEVE (AS1072 SIL FG)(5 min) /11/ /12/275 MAXMIN.840.658.970.7881.150.9681.3801.1981.5901.3181.7501.5681.9501.768TBDTBDB FIRESLEEVE INTEGRALSILICONE (5 min) /8/275 MAXMINTBDTBDTBDTBDTBDTBDTBDTBDC PROTECTIVE SLEE

11、VESHRINK-ON (POLYOLEFINAS1073 CODE B) /21/275 MAXMIN.520.450.620.550.795.7251.000.9201.1701.0601.4601.350TBD TBDTABLE 3 - ASSEMBLY LENGTH TOLERANCEHOSE ASSEMBLY LENGTH TOLERANCEUNDER 18 in .125 in18 THRU 36 in EXCLUSIVE .250 in36 THRU 50 in EXCLUSIVE .500 in50 in AND OVER 1%Copyright SAE Internation

12、al Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-(R) HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED,STANDARD DUTY, 3000 PSI, 275 F, TITANIUMFITTINGS, FLARELESS, 90 TO 90AEROSPACE STANDARDAS4573SHEET 3 OF 4AS4573REV.BREV. BNOTES:1.

13、 MATERIALS:a. HOSE AND FITTINGS - PER AS1975b. SLEEVES - SEE APPLICABLE STANDARDS, TABLE 2/2/ THIS PRODUCT SHALL BE QUALIFIED IN ACCORDANCE WITH PROCUREMENT SPECIFICATION AS1975 CLASS 3000. USERS OF THIS STANDARD SHALL PROCURE THIS PRODUCT FROM ACCREDITED MANUFACTURER(S), OR THEIR ACCREDITED DISTRIB

14、UTOR(S), AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS1975 CLASS 3000 FOR THIS STANDARD. CHANGE-OVER FROM USER-QPL TO PRI-QPL SHALL BE IN ACCORDANCE WITH AS1975 REVISION C OR HIGHER AND BE COMPLETED WITHIN SIX MONTHS FROM THE DATE OF ISSUE OF THIS STANDARD.3.

15、 CONSTRUCTION AND PERFORMANCE PER AS1975 CLASS 3000. FITTINGS SHALL BE PERMANENTLY ATTACHED TO THE HOSE.4. OPERATING CHARACTERISTICS PER AS1975.5. MARKING: MARKING SHALL BE PER AS1975 ON A STAINLESS STEEL BAND NOT OVER 1.0 in WIDE OR ON THE COLLAR. THE CHARACTERS SHALL BE A MINIMUM OF .06 in HIGH. T

16、HE BAND SHALL BE SO DESIGNED AS TO REMAIN TIGHT ON THE HOSE TO PREVENT RELATIVE MOVEMENT AND RESULTANT CHAFING. IT SHALL BE OF SUFFICIENT STRENGTH TO PREVENT REMOVAL BY HAND. HOSE ASSEMBLY DATE AND “PT” SYMBOL SHALL BE PERMANENTLY MARKED ON THE BAND OR ON AN END FITTING OR A FIRESLEEVE CLAMP. MARKIN

17、G BAND SHALL BE COVERED WITH TRANSPARENT POLYOLEFIN SHRINK SLEEVE PER AS1073 CODE A./6/ LENGTH “L” IS A THREE DIGIT NUMBER OF WHICH THE FIRST TWO DIGITS DESCRIBE THE HOSE ASSEMBLY LENGTH IN WHOLE INCHES, AND THE FOURTH DIGIT, THE FRACTION OF AN INCH IN EIGHTHS. LENGTH “L” IS MEASURED FROM “GAGE DIAM

18、ETER” TO “GAGE DIAMETER”. FOR LENGTH TOLERANCES SEE TABLE 3. “END TO END” LENGTH MEASUREMENTS IS THE SAME AS THE “GAGE DIAMETER” TO “GAGE DIAMETER” BECAUSE BOTH ENDS ARE 90 ELBOWS./7/ A TRUE CIRCULAR CROSS SECTION IS NOT REQUIRED THROUGH THE FITTING ID. HOWEVER, THE APPLICABLE MINIMUM BALL DIAMETER

19、LISTED IN TABLE 1 MUST BE CAPABLE OF PASSING THROUGH THE HOSE ASSEMBLY./8/ DISTANCE ACROSS CORNERS OF THE HEX MAY EXCEED THIS DIMENSION./9/ FITTING END IN SIZE CODES E THROUGH M MUST CONFORM TO NAS1760 TO MATE WITH AS33514 OR AS4375. FITTING END FOR SIZE CODE N AND LARGER MUST CONFORM TO AS4703 TO M

20、ATE WITH AS4658 OR AS4659. STANDARD COUPLING NUTS SHALL BE IN ACCORDANCE WITH OR EQUIVALENT TO AS5234 OR AS4370. SIZE CODE N AND LARGER NUTS SHALL CONFORM TO AS4660 OR AS4702. NUTS SHALL MEET THE TORQUE REQUIREMENTS PER AS1975.TABLE 4 - HOSE AND FITTING WEIGHTSHOSEORSLEEVECODE HOSE OR TYPE OR PART U

21、NITSHOSESIZE.250HOSESIZE.375HOSESIZE.500HOSESIZE.625HOSESIZE.750HOSESIZE1.000HOSESIZE1.250HOSESIZE1.500- BRAIDED HOSE ONLY PER AS1975 LB/IN (MAX) .006 .008 .012 .020 .025 .040 .050 TBDA FIRESLEEVE AS1072 (5 minPER AS1055) /15/LB/INB FIRESLEEVE INTEGRAL WITHHOSE (5 min PER AS1055) /15/LB/INC PROTECTI

22、VE SLEEVE SHRINK-ON(POLYOLEFIN AS1073, CODE B) /21/LB/IN .001 .001 .001 .002 .002 .003 TBD TBDNONE FIRESLEEVE CLAMP LB/EA (REF) .020 .020 .021 .021 .025 .025 .032 TBDNONE FITTING END (90) TITANIUM /16/ LB/EA (REF) .077 .121 .176 .310 .560 .950 TBD TBD /9/Copyright SAE International Provided by IHS u

23、nder license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-(R) HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED,STANDARD DUTY, 3000 PSI, 275 F, TITANIUMFITTINGS, FLARELESS, 90 TO 90AEROSPACE STANDARDAS4573SHEET 4 OF 4AS4573REV.BREV. B/10/ DIAMETERS ARE LISTED FO

24、R CLAMP SELECTION. TUBULAR SLEEVES MAY NOT BE A PERFECT ROUND AND SHALL BE MEASURED WITH A DIAMETER TAPE RULE (OFTEN REFERRED TO AS A PI-TAPE)./11/ THE TABLE 2 SLEEVE DIAMETERS FOR AS1072 SLEEVES APPLY WHEN THE SLEEVE IS COMPRESSED, OR CLAMPED, TO CONTACT THE HOSE. IN THIS CASE, A WRINKLE MAY OCCUR

25、OVER APPROXIMATELY 10% OF THE SLEEVE CIRCUMFERENCE./12/ THE CUT ENDS OF THE FIRESLEEVE SHALL BE COATED WITH RTV SILICONE RUBBER PRIOR TO INSTALLATION TO PREVENT WICKING OF FLUIDS. THE FIRESLEEVE ENDS SHALL BE SECURED TO THE HOSE ASSEMBLY END FITTINGS WITH CORROSION RESISTANT STEEL BANDS. AFTER INSTA

26、LLATION, CRACKS OR VOIDS IN THE FIRESLEEVE, WHICH EXPOSE THE FIBERGLASS, SHALL BE COATED WITH RTV SILICONE RUBBER./13/ THE END OF THE INTEGRAL FIRESLEEVE SHALL BE COVERED WITH SILICONE EXTENDING OVER THE END FITTING COLLAR.14. ADD “AS1055 TYPE Ib CLASS A-S/P” OR “AS150 TYPE XIII” TO IDENTIFICATION M

27、ARKING TO SHOW LEVEL OF COMPLIANCE, “FIRE RESISTANT” 275 F (5 min), WITH AS1055 OR AS150./15/ WHEN FIRESLEEVES ARE REQUIRED, WEIGHT LIMITS SHALL BE DEFINED BY THE PROCURING AUTHORITY./16/ TITANIUM PARTS MAY BE REPLACED WITH STAINLESS STEEL IF MAXIMUM WEIGHT FOR FITTING IS NOT EXCEEDED AND THE STAINL

28、ESS STEEL COMPONENTS HAVE BEEN PREVIOUSLY QUALIFIED.17. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994./18/ THE FITTING ORIENTATION DASH NUMBER IS A THREE DIGIT NUMBER DEFINING THE RELATIVE POSITION OF THE END FITTINGS IN 1 INCREMENTS (EXAMPLE 090 = 90). FITTING ORIENTATION SHALL BE MEASURED COUNTER

29、CLOCKWISE FROM THE NEAREST END FITTING, WHICH SHALL BE IN THE RELATIVE 000 POSITION (SEE FIGURE 2). WHEN END FITTINGS ARE POINTED IN THE SAME DIRECTION, THIS DASH NUMBER SHALL BE 000.19. SAFETY WIRE HOLES LOCATION AND DIAMETER PER AS1043 CODED AS FOLLOWS:a. U = TWO HOLES 180 APARTb. W = THREE HOLES

30、120 APART20. THIS PART STANDARD TAKES PRECEDENCE IN CASES OF CONFLICT.21. EXAMPLE OF PART NUMBER:22. ALL ASSEMBLIES PROCURED TO THIS STANDARD PRIOR TO REVISION B CAN BE UTILIZED FOR EITHER CLASS 3000 OR CLASS 4000 SYSTEM APPLICATIONS. ALL FUTURE PROCUREMENTS TO THIS STANDARD SHALL BE FOR CLASS 3000

31、ONLY. REFER TO AS4585 FOR PROCUREMENT OF CLASS 4000 HOSE ASSEMBLIES.23. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-