ANSI UL 2586B-2015 UL Standard for Safety Hose Nozzle Valves for Diesel Fuel Biodiesel Fuel Diesel Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20) Ker.pdf

《ANSI UL 2586B-2015 UL Standard for Safety Hose Nozzle Valves for Diesel Fuel Biodiesel Fuel Diesel Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20) Ker.pdf》由会员分享，可在线阅读，更多相关《ANSI UL 2586B-2015 UL Standard for Safety Hose Nozzle Valves for Diesel Fuel Biodiesel Fuel Diesel Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20) Ker.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 2586B Hose Nozzle Valves for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel OilUL COPYRIGHTED MATERIAL

2、NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Hose Nozzle Valves for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nom

3、inal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 2586B First Edition, Dated February 20, 2015 Summary of Topics This rst edition of the Standard for Hose Nozzle Valves for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to

4、 20 Percent (B20), Kerosene, and Fuel Oil, ANSI/UL 2586B, covers valves that are intended to be used for the control of uids and their vapors. They are of the type commonly used in piping systems and in the assembly of motor fuel dispensing equipment. The requirements are substantially in accordance

5、 with Proposal(s) on this subject dated October 17, 2014. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provide

6、s this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of

7、prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for thi

8、s Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or d

9、eviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the

10、note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. FEBRUARY 20, 2015 UL 2586B tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPROD

11、UCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 20, 2015 UL 2586B tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL February 20, 2015 1 UL 2586B Standard for Hose Nozzle Valves for Diesel Fuel, Biodiesel Fuel

12、, Diesel/ Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil Prior to the rst edition, the requirements for the products covered by this standard were included in the Outline of Investigation for Hose Nozzle Valves for Diesel Fuel, Biodiesel Fuel, D

13、iesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 2586B. First Edition February 20, 2015 This ANSI/UL Standard for Safety consists of the First Edition. The most recent designation of ANSI/UL 2586B as an American National Standard (ANSI)

14、occurred on February 20, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal

15、Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standa

16、rds shall remain the sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 2586B-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 20, 2015 UL 2586B 2 No Text on This PageUL COPYRIGHTED MATERIAL

17、NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 General 6 2.1 Components .6 2.2 Units of measurement .6 2.3 Undated references .7 3 Glossary .7 CONSTRUCTION 4 Assembly 8 4.1 General .8 4.2 Hose nozzle valves .8 5 Materials 9 5.1 M

18、etallic materials .9 5.2 Nonmetallic materials 11 5.3 Casting impregnation materials 13 5.4 Internal parts .13 6 Bodies and Covers 14 7 Diaphragms 16 8 Springs 16 9 Operating Mechanisms 16 PERFORMANCE 10 General 17 11 Deformation Test .18 12 Long Term Exposure Test .18 12.1 General .18 12.2 Samples

19、19 12.3 Method .19 12.4 Results .20 13 External Leakage Test 20 14 Hose Nozzle Valve Guard Strength Test 21 15 Operation Test .22 15.1 Automatic hose nozzle valve .22 15.2 Bellows secondary shut off operation .23 16 Pull Test 23 17 Sensitivity Test 23 18 Hose Nozzle Endurance Test 24 19 Bellows Seco

20、ndary Shut Off Operation Test .24 20 Visible Discharge Indicator Tests .25 20.1 Thermal shock test .25 20.2 Drop test 25 21 Hydrostatic Strength Test .25 22 Electrical Continuity Test 26 23 Salt Spray Test 26 24 Moist Ammonia-Air Stress Cracking Test 27 25 Marking Adhesion Test .27 FEBRUARY 20, 2015

21、 UL 2586B 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MANUFACTURING AND PRODUCTION 26 General .28 INSTALLATION INSTRUCTIONS 27 General .28 MARKING 28 General .29 SUPPLEMENT SA - Test Fluids SA.1 Representative aggressive combustible tes

22、t fuel mixtures SA1 FEBRUARY 20, 2015 UL 2586B 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover hose nozzle valves that are intended to be used for the control of motor fuels as indicated in

23、1.2. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with motor fuels which are handled at temperatures within the range of minus 29C (minus 20F) to 52C (125F) and an operating pressure of minimum 50 psi (350 kPa). 1.2 Hose nozzle

24、 valves covered by these requirements are intended for use with one or more of the following as applicable: a) Diesel fuel and diesel/biodiesel blends with nominal biodiesel concentrations up to 5 percent (B0 B5) formulated in accordance with the Standard Specication for Diesel Fuel Oils, ASTM D975;

25、 b) Diesel /biodiesel blends with nominal biodiesel concentrations from 5 percent up to 20 percent (B6 B20) formulated in accordance with the Standard Specication for Diesel Fuel Oil, Biodiesel Blends (B6 B20), ASTM D7467; c) Biodiesel (B99.9/B100) formulated in accordance with the Standard Specicat

26、ion for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels, ASTM D6751; d) Kerosene formulated in accordance with the Standard Specication for Kerosine, ANSI/ ASTM D3699; or e) Fuel oil (heating oil) formulated in accordance with the Standard Specication for Fuel Oils, ASTM D396. 1.3 Thes

27、e requirements cover hose nozzle valves of the manually operated and automatic pressure operated type. When they form a part of an assembly which provides for additional functions or service, the requirements are outside the scope of these requirements. 1.4 When they form a part of an assembly which

28、 provides for additional functions or service, the requirements are outside the scope of these requirements. 1.5 These requirements do not cover the following: a) Hose nozzle valves for handling liquids under cryogenic conditions. b) Hose nozzle valves for general renery service, offshore and pipe l

29、ine terminals, natural gas processing plants, gas distribution systems, petrochemical processing facilities, or the like. c) Hose nozzle valves operated wholly or partially by electricity or battery. FEBRUARY 20, 2015 UL 2586B 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTR

30、IBUTION WITHOUT PERMISSION FROM UL 1.6 This standard does not cover hose nozzle valves for use with gasoline or gasoline/ethanol blends which are covered under the Standard for Hose Nozzle Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85),

31、UL 2586A. 1.7 This standard does not cover hose nozzle valves for use with liqueed petroleum gas (LP-Gas), which are covered under the Standard for Flow Control Valves for Anhydrous Ammonia and LP-Gas, UL 125. 1.8 Requirements for the installation and use of these dispensing devices are included in

32、the Code for Motor Fuel Dispensing Facilities and Repair Garages, ANSI/NFPA 30A. 2 General 2.1 Components 2.1.1 Except as indicated in 2.1.2, a component of a product covered by this standard shall comply with the requirements for that component. 2.1.2 A component is not required to comply with a sp

33、ecic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.1.3 A component shall be used in accordance with its rating established for the intended c

34、onditions of use. 2.1.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic condit

35、ions. 2.1.5 A hose nozzle valve with an integral swivel shall be additionally evaluated to the Electrical-Continuity and Operation Tests in the Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nomi

36、nal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 567B. The force is to be applied at the point on the swivel farthest from the joint. When necessitated by the swivel construction, this test is to be conducted on additional samples of the swivel with the load applied on

37、 the opposite side of the plane of rotation. See UL 567B, Figures 16.1 16.3 for examples. 2.2 Units of measurement 2.2.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. FEBRUARY 20, 2015 UL 2586B 6UL COPYRIGHTED MATERIAL NOT AU

38、THORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2.3 Undated references 2.3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 3 Glossary 3.1 For th

39、e purpose of this standard, the following denitions apply. 3.2 DIESEL/BIODIESEL BLENDS Blended fuels composed of a diesel component and a biodiesel component. The numerical value corresponding to the biodiesel component determines the blend rating (such as B20 for 20% biodiesel, 80% diesel). 3.3 HOS

40、E NOZZLE VALVE, AUTOMATIC A hose nozzle valve which is held open during the entire lling operation. It may be held open by manual force or by an integral hold-open or latching device. It incorporates a mechanism that shuts off the ow of liquid during refueling operations to prevent overow from the l

41、l opening when liquid reaches a predetermined point on the spout. 3.4 HOSE NOZZLE VALVES A self-closing device designed to control the ow of ammable and combustible liquids at an operating pressure of minimum 50 psi (345 kPa). It is intended for use at the outlet end of a hose for dispensing ammable

42、 liquids. 3.5 HOSE NOZZLE VALVE, MANUALLY OPERATED A hose nozzle valve that is manually held open during the entire lling operation and closes only upon release of the manual force. 3.6 HOSE NOZZLE VALVE, VAPOR RECOVERY A system constructed to capture vapors displaced during lling operations. The va

43、pors are not processed during the course of this activity. a) Assist Nozzle A vacuum or pump is used to draw the vapors back to tank. b) Balance Nozzle Displacement of vapors from tank being ll forces the vapor back into the storage tank. 3.7 SEALS, DYNAMIC A seal that is subject to mechanical movem

44、ent or other applied forces that result in movement or exing of the seal under normal use conditions. 3.8 SEALS, STATIC A seal that is not subject to mechanical movement or other applied forces other than compressing forces that are applied during installation, after which, the seal is held in place

45、 during normal use conditions. FEBRUARY 20, 2015 UL 2586B 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONSTRUCTION 4 Assembly 4.1 General 4.1.1 A hose nozzle valve shall include all of the components required for its intended function a

46、nd installation. 4.1.2 A seat disc shall be attached to its poppet or holder or otherwise assembled so as to prevent it from becoming dislocated under service conditions as determined by the Hose Nozzle Endurance Test, Section 18. The means to secure the disc shall not rely upon cement or adhesive.

47、4.1.3 A brazing material used for joining liquid conning parts of a valve shall have a melting point (solidus temperature) of minimum 538C (1000F). 4.2 Hose nozzle valves 4.2.1 A hose nozzle valve shall be of the manually-operated or of the automatic type. A manually-operated valve requires the valv

48、e to be manually held open during the entire lling operation without the aid of hold-open devices or latches, but is capable of closing automatically. An automatic valve requires the valve to: a) Be manually opened, but is capable of being held open during the lling operation by a latch or other dev

49、ice and b) Is provided with automatic closing features. Exception: A hose nozzle valve for use in salt water or boat yard environments shall be of the automatic closing type without a latch-open device. 4.2.2 Automatic hose nozzle valves equipped with an integral hold open or latching device shall be so designed that, if left in the latched position after the ow has been stopped by means other than the automatic feature of the hose nozzle, it shall automatically unlatch whe