ANSI TIA-455-87-B-1993 FOTP-87 Fiber Optic Cable Knot Test《光缆结试验》.pdf

《ANSI TIA-455-87-B-1993 FOTP-87 Fiber Optic Cable Knot Test《光缆结试验》.pdf》由会员分享，可在线阅读，更多相关《ANSI TIA-455-87-B-1993 FOTP-87 Fiber Optic Cable Knot Test《光缆结试验》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA-455-87-B (Revision of EIA-455-87-A) March 1993FOTP-87 Fiber Optic Cable Knot Test ANSI/TIA-455-87-B-1993 APPROVED: MARCH 1993 REAFFIRMED: MAY 11, 1999 REAFFIRMED: MAY 10, 2005 REAFFIRMED: MARCH 22, 2013 NOTICE TIA Engineering Standards and Publications are designed to serve the public interest

2、through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publica

3、tions shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or int

4、ernationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publica

5、tion. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitatio

6、ns before its use. (From Project No. ANSI/TIA-PN-455.87-RF3, formulated under the cognizance of the TIA TR-42 Telecommunications Cabling Systems, TR-42.12 Subcommittee on Optical Fibers and Cables). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 1320 N. Cour

7、thouse Road Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call IHS, USA and Canada (1-877-413-5187) International (303-397-2896) or search online at http:/www.tiaonline.org/standards/catalog/

8、 All rights reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this docum

9、ent, please contact the TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.tiaonline.org/standards/catalog/info.cfm#copyright or Telecommunications Industry Association Technology (b) there is no assurance

10、 that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectu

11、al property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder t

12、hereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead

13、 left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its c

14、ontents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference

15、consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy

16、of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a clai

17、m of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. A

18、LL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHT

19、S. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO

20、 IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAM

21、AGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A

22、FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Section Appendix Figure Copyright Telecommunications Industry Association Provided by IHS under license with EIA No reproduction or networking permitted without license f

23、rom IHS - - - . . - - . - . . - FOTP-87 FIBER OPTIC CABLE KNOT TEST CONTENTS Title INTRODUCTION APPLICABLE DOCUMENTS APPARATUS SAMPLING AND SPECIMENS PROCEDUFE CALCCLATIONS OR INTERPEETATION OF RESULTS DOCUMENTATION SPECIFICATION INFORMATION Comparison between FOTP-87 and IEC, CCITT, and IS0 Require

24、ments Knot Test Setup with Mandrel-Procedure A Knot Test Setup with no Mandrel-Procedure B Examples of Minimum Cross-sectional Diameter - i - Sold to:TIA, 01429452 Not for Resale,200415112 17:3:23 GMT Page TIA-155-87-B Page 1 FBER OPTIC CABLE KNOT TEST (From EM Standards Proposal Number 2285, formul

25、ated under the cognizance of TIA FO-6.7 Subcommittee on Fiber Optic Cables.) This FOTP is part of the series of test procedures included within Recommended i: Standard TIA/EIA-455. NOTE: This FOTP was previously published in EIA-455-87A as FOTP-87. 1. INTRODUCTION 1.1 Intent. The intent of this knot

26、 test is to determine the self-limiting protection built into a cable to prevent the optical fiber from being bent to the point of mechanical or optical failure, as specified in the Detail Specification. 1.2 Scope. This test method may be used to test any type of fiber optic cable, using the appropr

27、iate Procedure (see 1.3 and Section 5) and test parameters, as required by the Detail Specification. 1.3 Summary of the Test Method. The test method evaluates the effect of a severe bend in a fiber optic cable due to a knot. Two Procedures are described: Procedure A uses a mandrel to limit the degre

28、e of bend of the cable. Procedure B uses no mandrel, allowing the stiffness of the cable, together with the applied load, to limit the bend. Procedure A may be used to evaluate increases in fiber attenuation in a controlled manner. Procedure B may be used to determine the ultimate bending capability

29、 of the cable, considering fiber breakage or cable damage. (Note that Procedure B was the only procedure in the previous revisions of FOTP-87. See 1.6 for discussion.) 1.4 Procedure Defaults. Section 8 defines the detailed specification requirements that are required to be specified in the Detail Sp

30、ecification to properly utilize this FOTP. “Default“ requirements are those that apply if no other alternative requirements are given in the Detail Specification. Procedure Defaults are provided for the convenience of users of this FOTP. They are stated in Sections 3 and 5 and are summarized below:

31、a. Test Procedure A. b. A mandrel diameter equal to the minimum bend diameter of the cable, for Procedure A only. (See 8.1.3.) c. Maximum test force as shown in the schedule in 5.8.1. d Test force applied at a rate of 5 centimeters per minute and held at its maximum value for 1 minute. e. Visual exa

32、mination, as detailed in 5.12. Copyright Telecommuncations Industry Association Provided by IHS under license with EIA No reproduction or networking permitted without license from IHS Sold to:TIA, 01429452 Not for Resale,2004/5/12 17323 GMT 1.5 Potential Failure Modes for this test include, but are

33、not limited to, the following: 1.5.1 Optical performance degradation. 1.5.2 Cracking, splitting, or tearing of the cable jacket. Although, permanent deformation of the cable jacket may occur, this would not normally result in cable rejection. Any additional failure criteria shall be specified in the

34、 Detail Specification. 1.6 Obsolete References. If a specification makes reference to either the original EIA RS-455-87 or to EIA-455-87A, such testing may be accomplished using Procedure B of this FOTP. Users of Detail Specifications having such obsolete references are directed to 1.3 and Section 5

35、 for details of the differences in Procedures A and B. In such cases, users should carefully consider the recommendation that Procedure A be used in lieu of Procedure B. Whenever specifications refer to FOTP-87 without citing a specific Procedure (A or B) or without indicating a specific document re

36、vision level (-455-87, -455-87A, or -455-87B). the users should carefully consider the intent of the specification in determining whether to use Procedure A or B. (In general this applies to specifications published prior to the publication date of this revision.) 2. APPLICABLE DOCUMENTS: The follow

37、ing documents form a part of this FOTP to the extent referenced herein: FOTP- 13, EIA/TIA-455- 13 Visual and Mechanical inspection of Fibers. Cables, Connectors andlor Other Fiber Optic Devices. FOTP-20, TIA/EIA-S-ZOA Measuremenr of Change in Optical Trumminance. FOP-46, EIA/TIA-455-46A Spectral Att

38、enuation Measurement for Long-Length, Graded-lndex Optical Fibers. FOV-53, EIA/TIA355-53A Attenuation by Substitution Measurement for Mdrimde Graded-lndex Oprical Fibers or Fiber Assemblies used in Long Length Communications System. FOTP-57, EIAfTIA355-57A Optical Fiber End Preparation and Examhutio

39、n. FOTP-6 1. TIA/EIA-S-IA OTDR Measurement of Fiber or Cable Attenuation. FOTP-78, EIWIA-455-78A Spectral Attenuation Cutback Measurement for Single- Mode Optical Fibers. CEI IEC 794-1. Second Ed. (1987) Optical fibre cables, Part I. Generic Specijication. In process of preparation. Pending publicat

40、ion of this revision, use the previous issue. Copyright Telecommunicatons Industry Association Provided by IHS under license with EIA Sold to:TIA, 01429452 No reproduction or networking permitted wthout license from IHS Not for Resale.2004/5/12 17:3:23 GMT . - -. .- - . . . . -. . . - . - . . . . -

41、TlA-455-87-B Page 3 3. APPARATUS: The test fixture (see Figures 1 and 2) shall consist of: 3.1 Appropriate clamping devices, as follows: 3.1.1 A restraining clamp to prevent the cable from slipping while the test force is applied. 3.1.2 A loading clamp to permit the application of the test force to

42、the cable. NOTE: The design of the restraining and force-application clamps used can be critical to the outcome of this test. The clamps shall be designed such that they are securely fastened to either the cable outer jacker or the strength members inside the cable, depending upon the cable design.

43、The clamps shall be designed such that they will not result in degradation of the optical performance of the fiber during either the preparation or execution of the test. If clamping methods are specified in the Detail Specification, they shall be used. 3.2 A device to apply the test force, such as

44、a test mass or a tensile testing machine. (The test force is discussed in 5.8.) 3.3 Mandrel: For Procedure A (defined in Section 3, a mandrel with an appropriate diameter, and a length at least four times the mandrel diameter is required. Unless otherwise specified in the Detail Specification, use a

45、 mandrel diameter equal to the minimum bend diameter of the cable to be tested. 3 Optical measuring equipment: Use appropriate optical measuring equipment, as required by the Detail Specificadon. Procedures which may be specified include, but are not limited to, FOTP-20, FOTP-36, FOTP-53, FOTP-61, a

46、nd FOTP-78. (See 5, 5.6, 5.8.3, and 5.10.) 4. SAMPLING AND SPECIhlESS Use a convenient length of the cable for the specimen. The specimen shall be long enough so that the optical performance may be 3ccuntely monitored to the limits established in he Detail Specification. The recommended minimum spec

47、imen length is approximately 5 meters (or 15 fr.). 5, PROCEDURE Conduct the cable knot test using one of the following two Procedures: Procedure A or Procedure B. These two Procedures are illustrated in Figures 1 and 2, respectively. Unless otherwise specified iri the Detail Specification and with t

48、he exception stated in 1.6, Procedure A shall be used. Gopyrlght Telecommuncations industry Association Provided by IHS under license with EIA No reproduction or networking permitted without license from IHS .- . . - . Sold to:TIA, 01429452 Not for Resale.2004/5112 17:3.23 GMT TL4-455-87-B Page 4 In

49、 Procedure A, a mandrel is placed inside the knot. This mandrel limits the severity of the test by restricting the bending of the cable to the mandrel diameter. Per 3.3, the mandrel diameter is usually equal to the minimum bend diameter of the cable, and if another mandrel diameter is to be used, it shall be specified in the Detail Specification. In Procedure B, no mandrel is used to limit the severity of the bend. The knot may result in the cable being bent tighter than its minimum bend diameter. Other than this difference, the test procedure for Procedure A and Proc