ANSI TIA EIA 568-B.2-1-2002 Commercial Building Telecommunications Cabling Standard - Part 2 Balanced Twisted Pair Components - Addendum 1 - Transmission Performance Specifications.pdf

《ANSI TIA EIA 568-B.2-1-2002 Commercial Building Telecommunications Cabling Standard - Part 2 Balanced Twisted Pair Components - Addendum 1 - Transmission Performance Specifications.pdf》由会员分享，可在线阅读，更多相关《ANSI TIA EIA 568-B.2-1-2002 Commercial Building Telecommunications Cabling Standard - Part 2 Balanced Twisted Pair Components - Addendum 1 - Transmission Performance Specifications.pdf（86页珍藏版）》请在麦多课文档分享上搜索。

1、TIA/EIA STANDARD Commercial Building Telecommunications Cabling Standard Part 2: Balanced Twisted Pair Cabling Components Addendum 1 - Transmission Performance Specifications for 4-pair Category 6 Cabling TIA/EIA-568-B .2-1 (Addendum No. 1 to TIA/EIA-568-B.2) JUNE 2002 TELECOMMUNICATIONS INDUSTRY AS

2、SOCIATION The Telmmmicalionu Industry A.wociation represatu the mmunicatimw secior of Elsctronic Industries Alliance Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE TWEIA

3、 Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the pro

4、per product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of TWEIA rom manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications pre

5、clude their voluntary use by those other than TIARIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by TIARIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TWEIA does not

6、assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user

7、of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal Nos.3-3727-ADl-B, 3-3727-AD1-B-1, and 3-3727-AD1-B-2, formulated under the cognizance of the TIA TR-42.7 Subcommittee on Telecom

8、munications Copper Cabling Systems.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION 2002 Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 PRICE: Please refer to current Catalog of EIA ELECTRONIC INDUSTRIES ALLIANCE STANDARDS and ENGINEERING PUBLICATIONS or call Glo

9、bal Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) All rights reserved Printed in U. S.A. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Co

10、pyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE OF DISCLAIMER AND LIMITATION OF LIABILITY The document to which this Notice is affixed has been prepared by one or more Engi

11、neering Committees of the Telecommunications Industry Association (“TIA”). TIA is not the author of the document contents, but publishes and claims copyright to the document pursuant to licenses and permission granted by the authors of the contents. TIA Engineering Committees are expected to conduct

12、 their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at . TIAS function is to administer the process, but not the content, of document preparation in accordance with the Manual and, when appropriate, the policies and pro

13、cedures of the American National Standards Institute (“ANSI”). THE USE OR PRACTICE OF CONTENTS OF THIS DOCUMENT MAY INVOLVE THE USE OF INTELLECTUAL PROPERTY RIGHTS (“IPR), INCLUDING PENDING OR ISSUED PATENTS, OR COPYRIGHTS, OWNED BY ONE OR MORE PARTIES. TIA MAKES NO SEARCH OR INVESTIGATION FOR IPR.

14、WHEN IPR CONSISTING OF PATENTS AND PUBLISHED PATENT APPLICATIONS ARE CLAIMED AND CALLED TO TIAS ATTENTION, A STATEMENT FROM THE HOLDER THEREOF IS REQUESTED, ALL IN ACCORDANCE WITH THE MANUAL. TIA TAKES NO POSITION WITH REFERENCE TO, AND DISCLAIMS ANY OBLIGATION TO INVESTIGATE OR INQUIRE INTO, THE SC

15、OPE OR VALIDITY OF ANY CLAIMS OF IPR. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS

16、 ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION. OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAG

17、ES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH

18、OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUC

19、H LIMITATIONS. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TINEIA-568-B.2-1 TRANSMISSION PERFORMANCE SPECIFICATIONS FOR 4-PAIR 100 !2 CATEGORY 6 CABLING TABLE OF CONTENTS 1

20、INTRODUCTION . 1 2 PURPOSE AND SCOPE . 1 3 NORMATIVE REFERENCES 2 4 DEFINITIONS. ACRONYMS parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated. ANSI and TIA maintain registers of currently valid nat

21、ional standards published by them. ANSMCEA S-80-576, Communications Wire and Cable for Wiring Premises, 1994 ANSM CEA S-90-661, Individually Unshielded Twisted Pair Indoor Cable for Use in Communication Wiring Systems, 1994 ANSITTIA/EIA-568-B. 1, Commercial Building Telecommunications Standard Part

22、1: General Requirements, 2001 ANSITTIA/EIA-568-B.2, Commercial Building Telecommunications Standard Part 2: Balanced Twisted-pair Cabling Components, 2001 ANSITTINEIA-568-B.2-3, Additional Considerations for Insertion Loss and Return Loss PasdFail Determination, 2002 ANSITTIA/EIA-568-B.3, Commercial

23、 Building Telecommunications Standard Part 3: Optical Fiber Cabling Components, 2000 ASTM D 4566-98, Standard Test Methods for Electrical Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable, 1998 IEC 60603-7, Connectors for frequencies below 3 MHz for use with pri

24、nted boards - Part 7: Detail specification for connectors, &way, including fixed and free connectors with common mating features, with assessed quality, 1996 4 DEFINITIONS, ACRONYMS & ABBREVIATIONS 4.1 Definitions The generic definitions in this section have been formulated for use by the entire fam

25、ily of telecommunications infrastructure standards. As such, the definitions do not contain mandatory requirements of the Standard. Specific requirements are found in the normative sections of this Standard. balance: Balance is the ratio of the differential signal output at either end of any pair to

26、 a common mode signal input, at either end of the same or a different pair, and vice versa, under specified termination conditions. insertion loss deviation: The difference between the actual insertion loss as measured on a permanent link or channel and the insertion loss as determined by adding the

27、 component losses. longitudinal conversion loss: A ratio, expressed in dB, of measured differential voltage relative to the common mode voltage on the same conductor pair applied at the same end. longitudinal conversion transfer loss: A ratio, expressed in dB, of measured differential voltage at one

28、 end of a conductor pair relative to the common mode voltage applied on any pair at the opposite end or on any other pair on the same end. modular plug cord: A length of cable with a modular plug on both ends. power sum attenuation to crosstalk ratio: A ratio, expressed in dB, determined by subtract

29、ing the insertion loss from the power sum near-end crosstalk loss. transverse conversion loss: A ratio, expressed in dB, of the measured common mode voltage on a pair relative to the differential mode voltage on the same pair applied at the same end. 2 Copyright Telecommunications Industry Associati

30、on Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TINEIA-568-B.2-1 4.2 Acronyms and abbreviations DUT Device under test I LD Insertion loss deviation LCL Longitudinal conversion loss LCTL Longitudinal conversion transfer loss

31、PSACR PWB Printed wiring board SIP IC SSTP Screened and shielded twisted-pair TCL Transverse conversion loss 5 TEST CONFIGURATIONS Power sum attenuation to crosstalk ratio Single Inline Package Integrated Circuit 5.1 Component test configurations Cable and connecting hardware test configurations and

32、 procedures are specified in ANSITTINEIA-568-B.2 with the additional requirements specified within this Standard. 5.2 Cabling test configurations The channel test configuration is described in ANSITTINEIA-568-B. 1. A supplemental schematic representation of the channel test configuration is illustra

33、ted in figure 1. Legend Cables and cords Connecting hardware Work area cord A Optional transition cabling B Horizontal cabling . C Patch cord or jumper cable . D Telecommunications room Horizontal cross-connect or equipment cord .E Telecommunications outlet Optional transition/consolidation connecto

34、r point connector . interconnect . CI Maximum length B + C . 90 m (295 fi) A + D + E . 10 m (32.8 fi) Figure 1 - Supplemental schematic representation of a channel test configuration 3 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproducti

35、on or networking permitted without license from IHS-,-,-TIA/EIA-568-B.2-1 The permanent link test configuration is defined in ANSITTIA/EIA-568-B. 1. A supplemental schematic representation of the permanent link test configuration is illustrated in figure 2. -b Permanent link under test i 4- Cables a

36、nd cords Connecting hardware Test equipment cord F Optional transition cabling . B Horizontal cabling C Telecommunications outlet/ Optional transition/consolidation connector point connector . interconnect. . Horizontal cross-connect or Maximum length B + C 90 m (295 ft) Figure 2 - Supplemental sche

37、matic representation of a permanent link test configuration 6 COMPONENTS 6.1 Recognized cable The following category of twisted-pair cable is recognized in addition to those identified in clause 4.2.1 of ANSlTTlAIEIA-568-B.2: Category 6: This designation applies to 1 O0 Q cables whose transmission c

38、haracteristics are specified up to 250 MHz. 6.1.1 Horizontal cable Four-pair 100 Q UTP and ScTP cables are recognized for use in category 6 horizontal cabling systems. The cable shall consist of 22 AWG to 24 AWG thermoplastic insulated solid conductors that are formed into four individually twisted

39、pairs and enclosed by a thermoplastic jacket. The cable shall meet all of the mechanical requirements of ANSI/ICEA S-80-576 applicable to four-pair inside wiring cable for plenum or general cabling within a building. In addition to the applicable requirements of ANSVICEA S-90-661-1994, the physical

40、design of horizontal cables shall meet the requirements of clauses 4.3.3.1 to 4.3.3.6 of ANSlTTlAIEIA-568-B.2. NOTE - Additional requirements for 100 Q ScTP cables are located in annex K of ANSITTINEIA-568-B.2. 4 Copyright Telecommunications Industry Association Provided by IHS under license with EI

41、ANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIAIEIA-568-B.2-1 6.1.2 Backbone cable Four-pair 100 Q UTP and ScTP cables are recognized for use in category 6 backbone cabling systems. The cable shall consist of 22 AWG to 24 AWG thermoplastic insulated solid cond

42、uctors that are formed into four individually twisted-pairs and enclosed by a thermoplastic jacket. The cable shall meet all of the mechanical requirements of ANSI/ICEA S-80-576 applicable to four-pair inside wiring cable for plenum or general cabling within a building. In addition to the applicable

43、 requirements of ANSMCEA S-90-661-1994, the physical design of backbone cables shall meet the requirements of clauses 4.4.3.1 to 4.4.3.6 of ANSITTIAIEIA-568-B.2. NOTE - Additional requirements for 100 Q ScTP cables are located in annex K of ANSITTINEIA-568-B.2. 6.1.3 Bundled and hybrid cable Bundled

44、 and hybrid cables may be used for horizontal and backbone cabling provided that each cable type is recognized (see clause 6.1.1 of this Standard and clause 4.4 of ANSITTIAIEIA-568-B.l) and meets the transmission and color-code specifications for that cable type as given in ANSITTIAIEIA-568-B.2, ANS

45、ITTIAIEIA-568-B.3, and clause 7 of this Standard. Additionally, for all frequencies from 1 MHz to 250 MHz, the total power sum NEXT loss for any disturbed pair from all pairs internal and external to that pairs jacket within the bundled or hybrid cable shall not exceed the values determined using eq

46、uation (1). Calculated power sum NEXT loss limit values that exceed 65 dB shall revert to a limit of 65 dB. psNEmbmdled - and - hbnd ,all - pairs - 41.1 - 15 log(f / 100) NOTES, 1 Hybrid UTP cables (color coded per ANSITTINEIA-568-B.2, clause 4.3.3.3) can be distinguished from multipair UTP backbone

47、 cables (color coded per ANSITTIAIEIA-568-B.2, clause 4.4.3.3) by the color coding scheme and by the transmission requirements. 2 Hybrid cables consisting of optical fiber and copper conductors are sometimes referred to as composite cables. The individual cables within a bundled cable shall meet the

48、 applicable requirements in clause 4 of ANSITTIAIEIA-568-B.3, clause 4 of ANSITTINEIA-568-B.2, annex K of ANSITTIAIEIA-568-B.2, annex M of ANSITTINEIA-568-B.2, and clause 7 of this Standard after bundle formation. 6.2 Recognized connecting hardware The following category of twisted-pair connecting h

49、ardware is recognized in addition to those identified in clause 5.4.1 of ANSITTIAIEIA-568-B.2: Category 6: This designation applies to 100 Q connecting hardware whose transmission characteristics are specified from 1 MHz to 250 MHz. 6.3 Cords Patch cords, equipment cords, and work area cords used for system moves, adds, and changes are critical to transmission performance. Category 6 cords and cordage shall meet the applicable requirements of clauses 6.1 thro