ANSI ISO IEC 11160-2-1996 Information technology - Office equipment - Minimum information to be included in specification sheets - Printers - Part 2 Class 3 and Class 4 printers (A.pdf

《ANSI ISO IEC 11160-2-1996 Information technology - Office equipment - Minimum information to be included in specification sheets - Printers - Part 2 Class 3 and Class 4 printers (A.pdf》由会员分享，可在线阅读，更多相关《ANSI ISO IEC 11160-2-1996 Information technology - Office equipment - Minimum information to be included in specification sheets - Printers - Part 2 Class 3 and Class 4 printers (A.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD ISO/IEC 11160-2 First edition 1996-08-01 Information technology - Office equipment - Minimum information to be included in specification sheets - Printers - Part 2: Class 3 and Class 4 printers Technologies de /information - iquipements de bureau - Information minima/e devant

2、figurer dans /es notices techniques - lmprimantes - Partie 2: lmprimantes classe 3 et classe 4 Adopted by INCITS (InterNational Committee for Information Technology Standards) as an American National Standard.Date of ANSI Approval: 1/11/99Published by American National Standards Institute,25 West 43

3、rd Street, New York, New York 10036Copyright 2002 by Information Technology Industry Council (ITI).All rights reserved.These materials are subject to copyright claims of International Standardization Organization (ISO), InternationalElectrotechnical Commission (IEC), American National Standards Inst

4、itute (ANSI), and Information Technology Industry Council(ITI). Not for resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, withoutthe prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 E

5、ye Street NW,Washington, DC 20005.Printed in the United States of AmericaISOAEC 11160-2:1996(E) Contents 1 Scope 2 Normative references 3 Conformance 4 Test and measurement conditions 5 Information to be included in the specification sheets Annex A - Classification of printers - Class 3 and Class 4

6、Annex B - Target Document Annex C - Classification of Printers Annex D - Bibliography Annex E - Example of a layout for a specification sheet 1 1 2 14 16 17 18 19 Q ISO/IEC 1996 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or

7、by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. ISOllEC Copyright Office l Case Postale 56 l CH-1211 Geneve 20 l Switzerland Printed in Switzerland ii 0 ISO/IEC 11160-2:1996(E) Foreword IS0 (the International Organizatio

8、n for Standardization) and IEC (the International Electrical Commission) form the specialised system for worldwide standardisation. National Bodies that are members of IS0 or IEC participate in the development of International Standards through technical committees established by the respective orga

9、nisation to deal with particular fields of mutual interest. Other international organisations, governmental and non-governmental, in liaison with IS0 and IEC, also take part to the work. In the field of information technology, IS0 and IEC have established a joint technical committee lSO/IEC JTCl. Dr

10、aft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75% of the national bodies casting a vote. International Standard ISO/IEC 11160-2, was prepared by Joint Technical

11、 Committee ISO/IEC JTCl, lnformafion technology, Subcommittee SC28, Office equipment. ISO/IEC 11160 consists of the following parts, under the general title Information technology - Office equipment - Minimum information to be included in specification sheet - Printers: - Part 1: Class 1 and Class Z

12、printers - Part 2: Class 3 and Class 4 printers Annexes A and B form an integral part of this part of ISO/IEC 11160. Annexes C, D and E are for information only. . Ill lSO/lEC 11160-2:1996 (E) 0 ISOAEC Introduction Printers of many different types and capacities are now available and their specifica

13、tions vary so widely that it is difficult for potential users to assess which machine might best meet their requirements. INTERNATIONAL STANDARD OISO/IEC ISO/lEC 11160-2:1996 (E) Information technology - Office equipment - Minimum information to be included in specification sheets - Printers - Part

14、2: Class 3 and Class 4 printers 1 Scope ISO/IEC 11160 is intended to facilitate the users in selecting a printer which meets their requirements. ISO/IEC 11160 specifies the minimum information that shall be included in the specification sheets of printers so that users may compare the characteristic

15、s of different machines. ISO/IEC 11160 applies to printers that could be operated in an office environment. Printers requiring specially equipped rooms or specially instructed operators are not considered in ISO/IEC 11160. ISO/IEC 11160 will accommodate different classes of printers. This part of IS

16、O/IEC 11160 accommodates Class 3 and Class 4 printers, as defined in annex B. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO/IC 11160. At the time of publication, the editions indicated were valid. Al

17、l standards are subject to revision, and parties to agreements based on this part of ISO/IC 11160 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards.

18、 IS0 216:1975”, Writing paper and certain classes of printed matter - Trimmed sizes - A and B series. IS0 554: 1976, IS0 7779: 1988”, Standard atmospheres for conditioning and/or testing - Specifications Acoustics - Measurement of airborne noise emitted by computer and business equipment. IS0 9295:1

19、988, Acoustics - Measurement of high-frequency noise emitted by computer and business equipment. IS0 9296:1988, ISO/IEC 10561), Acoustics - Declared noise emission values of computer and business equipment. Information technology - Printing devices - Method for measuring printer throughput. IEC 950:

20、1991, Safety of information technology equipment, including electrical business equipment. 3 Conformance In order to comply with this part of ISO/IEC 11160, specification sheets shall contain, in the order shown, all items listed in clause 5 which are relevant to the machine being described. 4 Test

21、and measurement conditions Unless otherwise specified, all tests and measurements shall be conducted at the following conditions: l Temperature: 18Cto25”C l Relative humidity: 30 % to 70 % 0 Line Voltage: rated input voltage l Line Frequency: rated frequency l Paper size: A4 I) Currently under revis

22、ion lSO/lEC 11160-2: 1996 (E) lSO/IEC l Paper weight: 60 g/m2 to 90 g/m2 l Paper transport direction: standard direction l Test pattern: as specified The test conditions shall be indicated in the specification sheet. Instead of A4 paper size, the size most commonly used in the country may be used, b

23、oth for the test page and the copies. This shall be indicated in the specification sheet. When weight of paper (g/m2) is given, it is assumed that the paper has been conditioned in the standard atmosphere defined in IS0 554 (temperature 20 “C f 2 “C; relative humidity 65 % * 5 %). 5 Information to b

24、e included in the specification sheets Table 1 defines, for each parameter, the number and name of the parameter and a short description of the entry. These constitute the information to be included in the specification sheet. The heading of the specification sheet shall indicate that it has been pr

25、epared in accordance with this part of ISO/IEC 11160. The numbers and headings of Table 1 shall be used. Not applicable parameters may be ignored, without changing the number of other parameters. The “Remarks and examples” column is provided for the persons who prepare the information sheet, and it

26、is not intended to appear in the specification sheet. The “Remarks and Examples” column is intended to be informative. Test methods to be applied, when not defined in other International Standards, are defined in this column. Whenever a capacity is given in sheets, the reference paper weight (g/m) s

27、hall be specified. Table 1 - Information to be included Parameter 1 General data Description of the entry Remarks and examples 1.1 Printer class Class 3 or Class 4 printer. See Annex B for description of classes. 1.2 Machine name, model and/or model number 1.3 Type Product name, model number. State

28、if the machine is portable, desk-top, or floor- standing. 1.4 Printing method The printing process used. ink-jet, thermal transfer, electrophotographic, ion deposit. 1.5 Dot density Horizontal and vertical dots per 25,4 mm (dpi) . The design capability of the machine to place the dots. Note that the

29、 theoretical writing resolution and the actual printing resolution may be different. If the dot density can be stepped up and down, all grades should be indicated. OISO/I EC lSO/lEC 11160-2: 1996 (E) Table 1 (contd) Parameter 1.6 Line smoothing Description of the entry Available/not available Remark

30、s and examples Indicate smoothing technology by type or trademarks 1.7 Dot depth Indicate the number of bits per dot available 1.6 Colour printing 1.8.1 Monochrome 1.8.2 Multi-colour Specify which colour. Available/not available. Also known as functional colour, spot colour, highlight or accent colo

31、ur. State the number of discrete colours that can be printed by colorants residing in the machine. 1.8.3 Full colour Available/not available. The full colour is often described as YELLOW, MAGENTA, CYAN Or YELLOW, MAGENTA, CYAN, BLACK. State if the machine can print full colour, continuous tone, half

32、-tone or both. 1.8.4 Colour transparencies Available/not available. Indicate if the colour can be projected. 2 Performance data 2.1 Rated engine speed First Page: Time in seconds Specify if monochrome, Continuous Print: Pages Per colour or both rates are Minutes (PPM) listed. This parameter is a dec

33、laration of manufacturer dealing with the mechanical aspect of the printer only. 3 lSO/lEC 11160-2: 1996 (E) OISO/IEC Table 1 (contd) Parameter 2.2 Warm-up time Description of the entry 1) Time in minutes and/or seconds from power up to ready state. 2) Time in minutes and/or seconds from power saver

34、 mode to ready state. Remarks and examples If the machine is pre-heated, this shall be indicated. If the printer is off, it shall measure the time between power on and the indication of a ready status. If the printer is in the power saver mode, it shall measure the time between the start command and

35、 the indication of a ready status or the beginning of printing. The value is rounded to the nearest whole number of seconds. 2.3 Recommended monthly print volume Manufacturers For the determination of this recommended range of use: parameter, the month is number of pages per month. considered consis

36、ting of 20 days of 8 hours each. Specify if monochrome, colour or both rates are listed. 2.4 First Page Out Time 2.5 Sustained Throughput Time in seconds from the Report two significant digits moment the mechanical (e. g. 4.5 seconds, 11 engine motion starts until the seconds). moment the first shee

37、t of paper is completely ejected into the output tray. To measure this parameter, a document as described in Annex D shall be created and sent to the printer. Performance in Pages Per Minute (PPM) that the printer is capable of sustaining. To measure this parameter, a document as described in Annex

38、D shall be created and sent to the printer. Measure the time (t, in seconds) between the first and the second page being ejected into the output tray. The sustained throughput (S) is calculated using the equation: s = 60. t The value S (PPM) shall be rounded off to at least two significant digits. 0

39、lSO/IEC lSO/lEC 11160-2: 1996 (E) Table 1 (contd) Parameter 3 Control Description of the entry Remarks and examples 3.1 Interface for hardware connection State the hardware connections available. Centronics, RS232, RS422, Token Ring, Ethernet. If automatic switching feature is available, state the f

40、eature here. 3.2 Interface for connection control Identify communication protocols. XON/XOFF, TCP/IP, AppleTalk. If multiple protocols are supported, state the feature here. 3.3 Interface for printer control Identify printer control PCL5, PostScript, Escape P, languages, including ISO/IEC 10180. ver

41、sion. 3.4 Memory 3.4.1 Standard memory 3.4.2 Optional memory Size in KB or MB. Size in KB or MB. Specify the method. Optional memory that can be added to support additional fonts or font processing. PCMCIA, SIMM. 3.5 Control panel 4 Printing features Describe the kind and size of the operator panel

42、and display. Alphanumeric 20 character display with 4 buttons and 4 status LED. 4.1 Printing margins In millimetres, from the top, Area in which printing is not bottom, left and right edges possible.(This area is given of the paper. on the condition that the print paper is fed through its ideal posi

43、tion). If the printing margins vary with paper sizes, this situation should be described. 4.2 Duplex printing Available/not available. State if special paper or accessories are available. Options shall be listed under parameter 16. 5 lSO/lEC 11160-2: 1996 (E) OISO/IEC Table 1 (contd) Parameter 4.3 O

44、ther printing features Description of the entry Remarks and examples Manufacturer may highlight Print Image Rotation: features or capabilities. Printer panel control capability to rotate the image which is described by incoming data. Image shift Fit Image to paper 5 Fonts and character sets The capa

45、bilities of the basic machine and the capabilities that can be added by 5.1 Resident Fonts 5.2 Standard Character Set 5.3 Optional Capabilities 6 Output material 6.1 Paper type List fonts or number of fonts available in the printer. List the character set (Glyph Index Mapping) available. List fonts

46、and character set optionally available. List the methods for optional font handling capability. additional print elements (external cartridges, external print elements, downloadable fonts) shall be clearly identified. Times Regular Type 1, Roman Italic True Type, 35 Type 1 fonts, 45 True Type Roman-

47、8, IS0 8859-l If the external cartridge or card with character sets is packed with printer, state here. Number of PCMCIA slots for the font cards. Download from a host computer. Additional hard disk for fonts. Plain, coated, thermal paper. The manufacturer shall specify for which characteristics of

48、the paper, other than normal paper, normal warranted performance can be assured. 6.2 Special material The manufacturer shall specify the printing materials that can be processed, possibly with degraded performances, e.g. Transparent sheets, labels, envelopes and recycled paper. OISO/IEC lSO/lEC 1116

49、0-2: 1996 (E) Table 1 (contd) Parameter 6.3 Paper size Description of the entry State the minimum and maximum width and the minimum and maximum length of the paper. This indication can be given either in millimetres or by quoting standard paper sizes. Remarks and examples 6.3.1 Cut sheets 6.3.2 Paper in continuous forms (roll or fanfold) Available/not available. A sizes (IS0 216), B sizes Standard name and/or sizes (IS0 216), North American of paper in millimetres. sizes. Available/not available. Indicate if length is manually Width, maximum and pre-selectable (maximum minimum in mill