ANSI INCITS ISO IEC 22050-2002 Information technology Data interchange on 12 7 mm 384-track magnetic tape cartridges Ultrium-1 format (Adopted by INCITS).pdf

《ANSI INCITS ISO IEC 22050-2002 Information technology Data interchange on 12 7 mm 384-track magnetic tape cartridges Ultrium-1 format (Adopted by INCITS).pdf》由会员分享，可在线阅读，更多相关《ANSI INCITS ISO IEC 22050-2002 Information technology Data interchange on 12 7 mm 384-track magnetic tape cartridges Ultrium-1 format (Adopted by INCITS).pdf（140页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference numberISO/IEC 22050:2002(E)ISO/IEC 2002INTERNATIONAL STANDARD ISO/IEC22050First edition2002-10-01Information technology Data interchangeon 12,7 mm, 384-track magnetic tape cartridges Ultrium-1 format Technologies de linformation change de donnes sur cartouches bande magntique 12,7 mm, 384

2、 pistes Format Ultrium-1 Adopted by INCITS (InterNational Committee for Information Technology Standards) as an American National Standard.Date of ANSI Approval: 7/7/2003Published by American National Standards Institute,25 West 43rd Street, New York, New York 10036Copyright 2003 by Information Tech

3、nology Industry Council (ITI).All rights reserved.These materials are subject to copyright claims of International Standardization Organization (ISO), InternationalElectrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry Council(ITI). Not f

4、or resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, withoutthe prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW,Washington, DC 20005.Printed in the United States of Ame

5、ricaISO/IEC 22050:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.

6、In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found

7、 in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the a

8、ddress given below. ISO/IEC 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below

9、or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO/IEC 2002 All rights reservedISO/IEC 22050:2002(E) ISO/IEC 2002 All rights reser

10、ved iiiContents Section 1 General 1 Scope 1 2 Conformance 1 2.1 Magnetic tape cartridge 1 2.2 Generating system 1 2.3 Receiving system 1 3 Normative references 1 4 Terms and definitions 2 4.1 Access Point 2 4.2 algorithm 2 4.3 algorithmically processed data 2 4.4 a.c. erase 2 4.5 Average Signal Ampl

11、itude 2 4.6 back surface 2 4.7 Beginning of Tape (BOT) 2 4.8 Beginning of Wrap (BOW) 2 4.9 bit 2 4.10 bit cell 2 4.11 Broad Band Signal-to-Noise Ratio (BBSNR) 2 4.12 byte 2 4.13 cartridge 2 4.14 Channel bit 3 4.15 Codeword 3 4.16 Codeword Pair 3 4.17 Codeword Quad (CQ) 3 4.18 CQ Set 3 4.19 cyclic re

12、dundancy check (CRC) character 3 4.20 Data Set 3 4.21 Data Set Information Table (DSIT) 3 4.22 End of Data (EOD) 3 4.23 End of Tape (EOT) 3 4.24 End of Wrap (EOW) 3 4.25 Error Correcting Code (ECC) 3 4.26 File Mark 3 4.27 flux transition position 3 4.28 flux transition spacing 3 4.29 forward tape mo

13、tion 3 4.30 header 3 4.31 Housekeeping Data Set 3 4.32 logical forword 4 4.34 Logical Point 4 4.35 magnetic tape 4 4.36 Master Standard Reference Tape (MSRT) 4 4.37 LTO Cartridge Memory (LTO CM) 4 4.38 Optimum Recording Current 4 ISO/IEC 22050:2002(E) iv ISO/IEC 2002 All rights reserved4.39 physical

14、 end of tape 4 4.40 physical forward 4 4.41 physical reverse 4 4.42 pre-record condition 4 4.43 processed data 4 4.44 Processed Record 4 4.45 Processing (Compression) 4 4.46 Protected Record 4 4.47 Record 5 4.48 recorded element 5 4.50 Reprocessing (Decompression) 5 4.51 reverse tape motion 5 4.52 r

15、un length limited encoding (RLL) 5 4.53 Secondary Standard Reference Tape (SSRT) 5 4.54 servo acquisition region 5 4.55 Standard Reference Amplitude (SRA) 4.56 Symbol 5 4.57 Synchronised Codeword Quad (SCQ) 4.58 Test Recording Density (TRD) 5 4.59 wrap 5 4.60 write equalisation 5 4.61 (1,7) RLL code

16、 5 5 Conventions and notations 6 5.1 Representation of numbers 6 5.2 Dimensions 6 5.3 Names 6 5.4 Alphanumeric string encoding 6 6 Acronyms 6 7 Environment and safety 6 7.1 Cartridge and tape testing environment 7 7.2 Cartridge operating environment 7 7.3 Cartridge storage environment 7 7.4 Tape ten

17、sion 7 7.5 Safety 7 7.6 Flammability 7 7.7 Transportation 7 Section 2 - Requirements for the Cartridge 8 8 Dimensional and Mechanical Characteristics of the Cartridge 8 8.1 Elements of the cartridge 8 8.2 Reference Planes of the case 8 8.3 Dimensions of the case 8 8.3.1 Overall dimension 8 8.3.2 Ref

18、erence points for reference planes 9 8.3.3 Positioning notches 10 8.3.4 Handling notches 10 8.3.5 Mis-insertion protection 11 8.3.6 Stacking features 11 8.3.7 Label area of the rear side 12 8.3.8 Central window 12 8.3.9 Sliding door 12 8.3.10 Case opening 12 8.4 Write-inhibit mechanism 13 ISO/IEC 22

19、050:2002(E) ISO/IEC 2002 All rights reserved v8.5 Flexibility of the case 13 8.5.1 Requirements 13 8.5.2 Procedure 13 8.6 Tape reel 13 8.6.1 Locking mechanism 13 8.6.2 Axis of rotation of the reel 14 8.6.3 Reel flanges 14 8.6.4 Metallic insert 14 8.6.5 Toothed rim 15 8.6.6 Hub of the reel 15 8.6.7 R

20、elative positions of hub and case 15 8.6.8 Characteristics of the toothed rim 15 8.7 Magnetic tape 16 8.7.1 Tape wind 16 8.7.2 Wind tension 16 8.7.3 Circumference of the tape reel 16 8.7.4 Moment of inertia 16 8.8 Leader pin assembly 17 8.8.1 Leader pin assembly dimensions 17 8.8.2 Leader tape attac

21、hment to leader pin assembly 17 8.8.3 Latching the leader pin assembly in the case 8.8.4 Mechanism and tape exit keepout area 18 8.9 LTO CM 18 8.10 Areas reserved for cartridge presence sensing 19 8.11 Handling grips and insertion indicator 8.11.1 Side grips 19 8.11.2 Insertion indicator 19 8.11.3 T

22、op grip 19 8.11.4 Bottom grip 20 8.12 Pad Printing Areas 20 8.13 Opacity 20 Section 3 - Requirements for the Unrecorded Tape 35 9 Mechanical, physical and dimensional characteristics of the tape 35 9.1 Materials 35 9.2 Tape length 35 9.2.1 Length of magnetic tape 35 9.2.2 Length of leader tape 35 9.

23、2.3 Length of splicing tape 35 9.3 Tape Width 35 9.3.1 Width of magnetic tape 35 9.3.2 Width of leader tape 35 9.3.3 Width of splicing tape 35 9.3.4 Procedure 36 9.4 Tape Thickness 36 9.4.1 Procedure 36 9.5 Longitudinal curvature 36 9.5.1 Procedure 36 ISO/IEC 22050:2002(E) vi ISO/IEC 2002 All rights

24、 reserved9.6 Edge Quality 36 9.6.1 Edge deviation 36 9.7 Tape flatness 37 9.7.1 Cupping 37 9.7.2 Curl/Twist 38 9.8 Coating adhesion 38 9.8.1 Procedure 38 9.9 Layer-to-layer adhesion 38 9.9.1 Requirement 38 9.9.2 Procedure 39 9.10 Coefficient of friction 40 9.10.1 Requirement 40 9.10.2 Procedure for

25、the measurement of the dynamic friction between the magnetic surface and the back surface 40 9.10.3 Procedure for the measurement of the dynamic friction between the back surface and SS-310 stainless steel 40 9.10.4 Procedure for the measurement of the dynamic friction between the magnetic surface a

26、nd AlO2/TiC ceramic 40 9.11 Surface quality 41 9.11.1 Surface roughness 41 9.12 Abrasivity 41 9.13 Tensile strength 41 9.13.1 Breaking strength 41 9.13.2 Offset yield strength 41 9.14 Longitudinal compliance 41 9.14.1 Procedure 42 9.15 Residual elongation 42 9.15.1 Requirement 42 9.15.2 Procedure 42

27、 9.16 Flexural rigidity 42 9.16.1 Requirement 42 9.16.2 Procedure 42 9.17 Transverse dimensional stability 42 9.18 Electrical resistance of coated surfaces 42 9.18.1 Requirement 42 9.18.2 Procedure 42 10 Magnetic Recording Characteristics 43 10.1 General 43 10.2 Test conditions 43 10.3 Optimum Recor

28、ding Current 44 10.4 Signal amplitude 44 10.5 Resolution 44 10.6 Overwrite 44 10.6.1 Requirement 44 ISO/IEC 22050:2002(E) ISO/IEC 2002 All rights reserved vii10.7 Ease of erasure 44 10.8 Broad Band Signal-to-Noise Ratio 44 10.8.1 Requirement 44 10.9 Tape quality 44 10.9.1 Missing pulses 44 10.9.2 Mi

29、ssing pulse zone 45 Section 4 - Requirements for an Interchanged Tape 45 11 Method of recording servo bands 45 11.1 General 45 11.2 Servo bands 45 11.2.1 Servo stripes 46 11.2.2 Servo bursts 46 11.2.3 Servo frames 46 11.2.4 Servo signal amplitude 47 11.2.5 Servo signal polarity 47 11.2.6 Servo defec

30、ts 48 11.3 Servo frame encoding 48 11.3.1 Method of encoding position and manufacturers data 48 11.3.2 LPOS word construction 50 11.3.3 Tape manufacturer encoding 51 11.3.4 Cross tape identification 53 11.4 Servo band location 53 11.5 Servo band pitch 53 11.6 Nominal servo locations 53 11.7 Long-ter

31、m average servo location 53 12 Method of recording data tracks 54 12.1 Physical recording density 54 12.2 Nominal bit cell length 54 12.3 Long-term average bit cell length 54 12.4 Short-term Average Bit Cell Length (STA) 54 12.5 Rate of change of the STA 54 12.6 Bit shift 54 12.7 Recording performan

32、ce test conditions 12.8 Track sequence addressing 54 12.9 Location of data tracks 55 12.10 Track width 55 12.11 Adjacent track pitch 56 12.12 Azimuth 56 12.13 Total character skew 56 12.14 Channel Layout 56 13 Format 57 13.1 General 57 13.2 Protected Record 58 13.3 Processed Protected Record Sequenc

33、e 59 13.3.1 Control Symbols 59 13.3.2 End Marker 60 13.3.3 Access Points 60 13.3.4 Alignment and append points 61 ISO/IEC 22050:2002(E) viii ISO/IEC 2002 All rights reserved13.4 Data Set 61 13.4.1 Format Identification Data Set (FID) 61 13.4.2 User Data Set 62 13.4.3 EOD Data Set 62 13.4.4 Housekeep

34、ing Data Set 62 13.5 Data Set Information Table (DSIT) 62 13.5.1 Drive Manufacturer Use 63 13.5.2 Drive Manufacturer Use C1 63 13.5.3 Reserved 63 13.5.4 Drive Manufacturers Identity 63 13.5.5 Data Set number 63 13.5.6 Valid Data Length 64 13.5.7 Access Point Offset 64 13.5.8 Total Records 64 13.5.9

35、Total File Marks 65 13.5.10 Record Count 65 13.5.11 File Mark Count 66 13.5.12 Thread Count 66 13.5.13 Data Set Type 66 13.5.14 Data Set Flags 67 13.5.15 Thread Write Pass 67 13.5.16 Tape Write Pass 67 13.6 ECC 67 13.6.1 Sub Data Set 68 13.6.2 C1 Sub Data Set 68 13.6.3 ECC Encoded Sub Data Set 69 13

36、.6.4 Codeword Pair designation 70 13.7 Codeword Quads (CQ) 70 13.7.1 Codeword Pair Header 71 13.7.2 First Codeword Pair 72 13.7.3 Second Codeword Pair 72 13.8 Allocation of CQs to Logical Tracks 73 13.9 Data randomisation 74 13.10 RLL encoding 74 14 Recording of data on tape 75 14.1 Synchronised Dat

37、a Set 75 14.1.1 Data Set Separator (DSS) 75 14.1.2 VFO Field 1 76 14.1.3 VFO Field 2 76 14.1.4 Synchronised Codeword Quad (SCQ) 76 14.2 Write equalisation bit encoding 77 14.3 Writing cells on tape 77 15 Regions on tape 77 15.1 Logical Points and regions 77 15.2 Calibration Region 79 15.3 User Data

38、Region 79 15.4 Interrupted Data Sets 79 15.5 Repeated CQ Sets 80 ISO/IEC 22050:2002(E) ISO/IEC 2002 All rights reserved ix15.6 Amble CQs 80 15.7 Beginning of Wrap (BOW) 81 15.8 End of Wrap (EOW) 81 15.9 Appending and Overwriting 81 15.10 Servo Tracking Faults 82 Annexes A - Measurement of Bit Shift

39、83 B - Measurement of Broad Band Signal-to-Noise Ratio 84 C - Tape Abrasivity Measurement Procedure 86 D - LTO Cartridge Memory 88 E - Flexural Rigidity Procedure 107 F - LTO CM electrical interface 109 G - Recommendations for transportation 126 H - Inhibitor Tape 127 I - Vendor code lists 128 ISO/I

40、EC 22050:2002(E) x ISO/IEC 2002 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the de

41、velopment of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-govern

42、mental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of

43、 the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote

44、. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 22050 was prepared by ECMA (as ECMA-319) and was adopted, under a spe

45、cial “fast-track procedure”, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel with its approval by national bodies of ISO and IEC. Annexes A to F form a normative part of this International Standard. Annexes G to I are for information only. INTERNATIONAL STANDARD ISO/I

46、EC 22050:2002(E) ISO/IEC 2002 All rights reserved 1. Information technology Data interchange on 12,7 mm, 384-track magnetic tape cartridges Ultrium-1 format Section 1 General 1 Scope This International Standard specifies the physical and magnetic characteristics of magnetic tape cartridges, using ma

47、gnetic tape 12,65 mm wide so as to provide physical interchange of such cartridges between drives. It also specifies the quality of the recorded signals, the recording method and the recorded format, thereby allowing data interchange between drives by means of such cartridges. The format supports va

48、riable length Logical Records, high speed search, and the use of a registered algorithm for data compression. This International Standard specifies four types of cartridges depending on the length of tape contained in the case. These four types are referred to as Type A, Type B, Type C and Type D; t

49、heir nominal capacity is 100 Gbytes, 50 Gbytes, 30 Gbytes and 10 Gbytes, respectively. NOTE - One Gbyte contains 1 000 000 000 bytes. Information interchange between systems also requires, at a minimum, agreement between the interchange parties upon the interchange code(s) and the specification of the structure and labeling of the information on the interchanged cartridge. This International Standard shall be used only in conjunction with ISO/IEC 22091. Together with a standard for volume and file structure, e.g. Standard