ANSI INCITS ISO IEC 10561-1999 Information technology - Office equipment - Printing devices - Method for measuring throughput - Class 1 and Class 2 printers.pdf

《ANSI INCITS ISO IEC 10561-1999 Information technology - Office equipment - Printing devices - Method for measuring throughput - Class 1 and Class 2 printers.pdf》由会员分享，可在线阅读，更多相关《ANSI INCITS ISO IEC 10561-1999 Information technology - Office equipment - Printing devices - Method for measuring throughput - Class 1 and Class 2 printers.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、B CReference numberISO/IEC 10561:1999(E)INTERNATIONALSTANDARDISO/IEC10561Second edition1999-05-01Information technology Officeequipment Printing devices Methodfor measuring throughput Class 1 andClass 2 printersTechnologies de linformation quipements de bureau Dispositifsdimpression Mthode de mesura

2、ge de la capacit Imprimantes declasses 1 et 2Adopted by INCITS (InterNational Committee for Information Technology Standards) as an American National Standard.Date of ANSI Approval: 1/3/01Published by American National Standards Institute,25 West 43rd Street, New York, New York 10036Copyright 2002 b

3、y Information Technology Industry Council (ITI).All rights reserved.These materials are subject to copyright claims of International Standardization Organization (ISO), InternationalElectrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry C

4、ouncil(ITI). Not for resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, withoutthe prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW,Washington, DC 20005.Printed in the Un

5、ited States of AmericaISO/IEC 10561:1999(E) ISO/IEC 1999All rights reserved. Unless otherwise specified, no part of this publication may be reproducedor utilized in any form or by any means, electronic or mechanical, including photocopying andmicrofilm, without permission in writing from the publish

6、er.ISO/IEC Copyright Office Case postale 56 CH-1211 Genve 20 SwitzerlandPrinted in SwitzerlandiiContents1 Scope 12 Normative references 13 Conformance 14 Test principles 15 Test conditions 26 Letter test 37 Spreadsheet test 38 Graphics test 49 Test report 4Annex A - Presentation of test results 5Ann

7、ex B - Letter test patterns 6Annex C - Spreadsheet test pattern 9Annex D - Graphic test pattern 11Annex E - Classification of printers - Classes 1 and 2 12ISO/IECISO/IEC 10561:1999(E)iiiForewordISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commi

8、ssion)form the specialized system for worldwide standardization. National bodies that are members of ISO or IECparticipate in the development of International Standards through technical committees established by therespective organization to deal with particular fields of technical activity. ISO an

9、d IEC technical committeescollaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, inliaison with ISO and IEC, also take part in the work.In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC J

10、TC 1.Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting.Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote.International Standard ISO/IEC 10561 was prepared by Joint Techni

11、cal Committee ISO/IEC JTC 1, Informationtechnology, Subcommittee SC 28, Office equipment.This second edition cancels and replaces the first edition (ISO/IEC 10561:1991), which has been technicallyrevised.Annexes A, B, C and D form an integral part of this International Standard. Annex E is for infor

12、mation only.INTERNATIONAL STANDARD ISO/IEC ISO/IEC 10561:1999(E)1Information technology Office equipment Printing devices Method for measuring throughput Class 1 and Class 2 printers1 ScopeThis International Standard specifies a method for measuring the throughput of class 1 and class 2 printers, as

13、defined in ISO/IEC 11160-1. This International Standard specifies three different test patterns: a standard business letter; a spreadsheet; a graphic pattern.In addition, this International Standard defines a method for a performance test and one for an endurance test.These tests are intended to mea

14、sure only the printer throughput for documents in the same class as the testpatterns and not to evaluate any other printer features such as character shaping, print compressions,network/controller performance, colour, etc. The method is relevant to class 1 and class 2 printer types (e.g. dotmatrix,

15、daisy wheel, ink jet, thermal transfer printers) and to all configurations (e.g. tractor feed, cut sheet feed,80-column and over 132-column print width, etc.). It is not the most suitable for comparing performance of otherclasses of printing devices such as high-speed page-oriented printers or color

16、 printers.This method is intended for use by printer manufacturers and test houses so that a common form of test resultpresentation shall be obtained. It will also enable a user to make a quick and easy comparison of the printingthroughput of different printers.2 Normative referencesThe following st

17、andards contain provisions which, through reference in this text, constitute provisions of thisInternational Standard. At the time of publication, the editions indicated were valid. All standards are subject torevision, and parties to agreements based on this International Standard are encouraged to

18、 investigate thepossibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintainregisters of currently valid International Standards.ISO/IEC 11160-1:1995, Information techology, Office equipment - Minimum information to be included inspecification sh

19、eets - Part 1: Class 1 and Class 2 printers.DIN 32751 - Bro- und Datentechnik - Drucker - Ermittlung der Druckleistung bezogen auf Prfvorlagen.3 ConformanceTest results claimed to be in conformance with this International Standard shall have been obtained in accordancewith the method specified in th

20、is International Standard.4 Test principles4.1 GeneralFor each test the specified test pattern shall be printed a number of times on the device under test. A test shall beperformed under the conditions specified in clause 5. The initial set-up conditions for the printer shall be asdescribed under ea

21、ch individual test. Once started a test shall be performed without interruption.The performance tests are designed to enable measurement of the printer under typical user application print tasks.The endurance tests are designed to show any effects of extended high duty print tasks on printing throug

22、hput, dueto any limiting factors within the printer (for example, dot density limitations, temperature rises, etc.).For both types of test the throughput unit shall be “printed pages per hour“ and shall be calculated by means of theformula:Number of printed pages x 3600 s/hMeasured time in secondsIS

23、O/IEC 10561:1999(E)ISO/IEC24.2 Performance testIn the performance tests the test pattern shall be transmitted from the host system five times, either as a single,five-page document or as five, single-page documents.The test time measurement shall start from the moment the data arrive at the printer

24、interface. Measurement fromthe moment the “start“ key is depressed on the host computer is permitted, if it can be proved that this does notaffect the test time measurement by more than 1 %.When the test is performed with cut sheet paper the test shall be started with the paper in its normal print m

25、ode. Forprinters pre-loading the paper, the paper path shall be cleared before each test.The measurement of the time required by the test shall end when the fifth sheet has been ejected.For a printer operating with continuous paper the test shall start with the paper loaded to the top of form positi

26、on.The measurement of the time required by the test shall end after execution of the form feed at the end of printingthe fifth page.The performance figures shall be recorded along with a reference to the matrix used.4.3 Endurance testIn the endurance tests the test pattern shall be transmitted from

27、the host system repeatedly for 1 h.The test time measurement shall start from the moment the data arrive at the printer interface. Measurement fromthe moment the “start“ key is depressed on the host computer is permitted, if it can be proved that this does notaffect the test time measurement by more

28、 than 1 %.When the test is performed with cut sheet paper the test shall be started with the paper in its normal print mode. Forprinters pre-loading the paper, the paper path shall be cleared before each test.For a printer operating with continuous paper the test shall start with the paper loaded to

29、 the top of form position.The measurement of the time requested by the test shall end with the completion (ejection) of the first sheet after1 h has elapsed (1 h and n seconds) so that a whole number of pages shall be printed.The 1 h test time shall include any time required to reload paper, change

30、ribbon cassette or replenish ink/tonersupplies. It is assumed that the test is commenced with new consumables, loaded to capacity.The endurance figures shall be recorded along with a reference to the matrix used.5 Test conditions5.1 Test environmentThe test shall be performed in the following enviro

31、nment.Temperature: 18 C to 25 CRelative humidity: 30 % to 70 %The printer, fully enclosed in its normal operating cover set, shall be acclimatized in the test environment in poweredcondition for at least 1 h.5.2 VoltageThe printer shall be connected to a voltage supply which remains within 10 % of t

32、he nominal value of the specifiedoperating voltage for the printer under test.5.3 Data inputData shall be sent to the printer at such a rate that the printer is never waiting for data to arrive and thereforeproducing a misleading (lower) throughput figure.5.4 Test sequenceEach test sequence shall be

33、 completed without stopping.After each test sequence the printer shall be allowed to re-stabilize (cool down) to its normal powered up ambientstate.ISO/IECISO/IEC 10561:1999(E)35.5 Print paperThe paper used shall have the following weight cut sheet: 60 g/m2 to 90 g/m2 fanfold single ply: 60 g/m2 to

34、80 g/m2 fanfold multiply: according to the manufacturers specification.For testing with fanfold multiply paper an original plus two copies shall be used. The manufacturer shall specify thetype of the paper and carbons.A printer configured for continuous paper (tractor, pin wheel or friction feed) sh

35、all preferably be loaded with304,8 mm (12 in) form length paper. If this is not possible any near equivalent length may be used but the testpatterns can then be printed over more than one page. Any “skip over perforation“ feature in the printer shall bedisabled.A printer configured for cut sheet pap

36、er shall be operated in automatic mode, not in manual single sheet feed mode.A4 size paper or near equivalent shall be used. If a size other than A4 is used, the size shall be so recorded in thetest results.The printer shall be tested with single ply paper and also with three-ply paper (original plu

37、s two copies). The multiplytest shall only apply if the printer can handle at least three-ply paper (original plus two copies, with or without carboninterleaves).6 Letter test6.1 GeneralThis test simulates a typical user application of printing a letter.6.2 Test patternsTwo test patterns are defined

38、 in annex B. The first one (pattern A) is the standard letter defined in DIN 32751. Thesecond pattern (pattern B) is a letter in English to be used for printers not printing diacritical signs. The results of thetwo test patterns are not comparable, and the test patterns used shall be declared in the

39、 test results.The printer shall be set up for 0,4 characters per millimetre (10 cpi)1)and 0,24 lines per millimetre (6 lpi)2)operation.If the manufacturer declares more than one print quality mode, test 1 shall be made with the printer set to the lowestquality mode, and tests 2 and 3 with the printe

40、r set to the highest quality mode.6.3 Test 1 - performanceSet the printer to the lowest quality mode.6.4 Test 2 - performanceSet the printer to the highest quality mode.6.5 Test 3 - enduranceSet the printer to the highest quality mode.7 Spreadsheet test7.1 GeneralThis test simulates a typical user a

41、pplication of printing a spreadsheet.If the manufacturer declares more than one print quality mode, the test shall be made with the printer set to thelowest quality mode and for 0,24 lines per mm (6 lpi).7.2 Test patternThe test pattern shall be the 132-column spreadsheet shown in annex C.1)cpi = ch

42、aracters per inch2)lpi = lines per inchISO/IEC 10561:1999(E)ISO/IEC47.3 Test 1 - performanceThe printer shall be set up for 0,4 characters per millimetre (10 cpi). This test shall not be performed on printershaving a print line length of less than 33,5 cm (13,2 in).7.4 Test 2 - performanceThe print

43、density mode shall be set to the compressed mode, normally 0,67 characters per millimetre (17 cpi). If thisis not available then a compression in the range 0,65 characters per millimetre to 0,71 characters per millimetre(16,5 cpi to 18 cpi) shall be selected.8 Graphics test8.1 GeneralThe test patter

44、n sent to the printer shall utilize graphics mode printing (e.g. vectors, bit map) and shall not usecharacter mode printing (e.g. block graphic characters).The dimensions defined are minimum dimensions. Any minor size deviations are permitted if they yield a larger butnot a smaller image.This graphi

45、c test shall only apply to the class 2 printers.8.2 Test patternThe test pattern shall be that reproduced in annex D.8.3 Test 1 - performanceThe minimum density to be tested is 2,63 horizontal x 2,83 vertical dots per millimetre (60 horizontal and 72 verticaldots per inch).9 Test reportResults recor

46、ded from the tests specified in clauses 6 to 8 shall be presented in the tabular format specified inannex A. The configuration used for the test shall be reported.It is recommended that this presentation format be used in all technical specifications, sales leaflets and informationmade available to

47、printer users.ISO/IECISO/IEC 10561:1999(E)5Annex A(normative)Presentation of test resultsPrinter type :Configuration :Letter test pattern:MatrixusedCont.One plyCont.multiplyCut sheetLetter-Performance Lowest qualityfive pages, 0,4 cpmm(10 cpi)Highest qualityLetter-endurance 1 h,0,4 cpmm (10 cpi)High

48、est qualityGraphics, five pagesPerformanceSpreadsheet, five pagesPerformance203,2 mm (8 in)Print width0,67 cpmm(17 cpi)lowest qualitySpreadsheet, five pagesPerformance355,3 mm (13,2 in)Print width0,4 cpmm(10 cpi)lowest qualityResults are given in printed pages per hour (pph).The matrix used is indic

49、ated by the number of dots (horizontal x vertical) per millimetre (inch).Results boxes may be left empty depending on the printer type.ISO/IEC 10561:1999(E)ISO/IEC6Annex B(normative)Letter test patternsTwo test patterns are defined and represented in the following pages.If this International Standard is translated into another language, the text of the standard letters shall not betranslated in order to ensure correlation between measurements made at different locations.For convenience of the user of this International Standard and to i