ANSI ASTM F1056-2018 Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings.pdf
《ANSI ASTM F1056-2018 Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings.pdf》由会员分享,可在线阅读,更多相关《ANSI ASTM F1056-2018 Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F1056 18 An American National StandardStandard Specification forSocket Fusion Tools for Use in Socket Fusion JoiningPolyethylene Pipe or Tubing and Fittings1This standard is issued under the fixed designation F1056; the number immediately following the designation indicates the year ofo
2、riginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers socket fusion tools for use inmak
3、ing socket fusion joints between polyethylene pipe ortubing and fittings as specified by Specifications D3035,D2513, and D2683. This specification covers newly manufac-tured heater faces and used heater faces which have beenrecoated. Requirements for materials, workmanship, and di-mensions are inclu
4、ded. Where applicable on this specification,“pipe” shall mean “pipe” and “tubing.”1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3
5、 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Tr
6、ade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2513 Specification for Polyethylene (PE) Gas PressurePipe, Tubing, and FittingsD2683 Specification for Socket-Type Polyethylene Fittingsfor Outside Diameter-Controlled Polyethy
7、lene Pipe andTubingD3035 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside DiameterF412 Terminology Relating to Plastic Piping Systems3. Terminology3.1 Definitions:3.1.1 GeneralDefinitions are in accordance with Termi-nology F412 and abbreviations are in accordance
8、 with Termi-nology D1600, unless otherwise specified.3.2 Definitions of Terms Specific to This Standard:3.2.1 chamfer toola device that is used to chamfer theoutside edge of the pipe. The chamfer allows the pipe end toeasily enter the pipe heater face and easily enter the heatedfitting. Chamfering i
9、s optional for all sizes but commonly donefor 114-in. IPS and larger sizes.3.2.2 depth gagea device that is used to locate therounding clamp a prescribed distance from the end of the pipe.3.2.3 heating toola device used to heat the heater faces.3.2.4 fitting heater face or adapterA block of heat con
10、-ducting material that attaches to the heating tool and isdimensioned to melt the internal surface of the fitting socket.3.2.5 pipe heater face or adapter A block of heat con-ducting material that attaches to the heating tool and isdimensioned to melt the external surface of the pipe.NOTE 1The fitti
11、ng heater face and pipe heater face can be in one blockof heat conducting material.3.2.6 rounding clamp or cold ringa device that is clampedaround the pipe to round the pipe and limit the distance the pipeend goes into the pipe heater face and the socket fitting.4. Materials and Manufacture4.1 Heate
12、r faces may be manufactured from aluminum,steel, or other suitable heat conducting material.NOTE 2Polyethylene may stick to hot metal heating surfaces. Thissticking may be minimized by covering the heating surfaces with astick-resistant coating such as polytetrafluoroethylene (PTFE) or polyphe-nylen
13、e sulfide (PPS). Copper or copper alloys are not suitable withoutcoating because some polyolefins react with copper.5. Dimensions, Mass, and Permissible Variations5.1 Heater face dimensions and tolerances shall be as shownin Table 1. The dimensions in Table 1 are for heater faces at thecommonly used
14、 operating temperature of 500F (260C).Annex A1 contains Table A1.1 which gives dimensions tomeasure for coated aluminum faces at 73.4F (23C).1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.20 on Joining
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
2000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ANSIASTMF10562018STANDARDSPECIFICATIONFORSOCKETFUSIONTOOLSFORUSEINSOCKETFUSIONJOININGPOLYETHYLENEPIPEORTUBINGANDFITTINGSPDF
链接地址:http://www.mydoc123.com/p-432723.html