ANSI ASME A112.18.2-2011 Plumbing Fixture Waste Fittings《卫生设备排污配件》.pdf

《ANSI ASME A112.18.2-2011 Plumbing Fixture Waste Fittings《卫生设备排污配件》.pdf》由会员分享，可在线阅读，更多相关《ANSI ASME A112.18.2-2011 Plumbing Fixture Waste Fittings《卫生设备排污配件》.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、ASME A112.18.2-2011/CSA B125.2-11Plumbing waste fittingsCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Legal Notice for Harmonized Standard Jointly Developed by ASME and CSA Intellectual property

2、 rights and ownership As between American Society of Mechanical Engineers (ASME) and Canadian Standards Association (CSA) (collectively ASME and CSA) and the users of this document (whether it be in printed or electronic form), ASME and CSA are the joint owners of all works contained herein that are

3、 protected by copyright, all trade-marks (except as otherwise noted to the contrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. The unauthorized use, modificatio

4、n, copying, or disclosure of this document may violate laws that protect the intellectual property of ASME and CSA and may give rise to a right in ASME and CSA to seek legal redress for such use, modification, copying, or disclosure. ASME and CSA reserve all intellectual property rights in this docu

5、ment. Disclaimer and exclusion of liability This document is provided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchan

6、tability, or its non-infringement of any third partys intellectual property rights. ASME and CSA do not warrant the accuracy, completeness, or currency of any of the information published in this document. ASME and CSA make no representations or warranties regarding this documents compliance with an

7、y applicable statute, rule, or regulation. IN NO EVENT SHALL ASME AND CSA, THEIR RESPECTIVE VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER C

8、AUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS

9、 TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF ASME OR CSA HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES. In publishing and making this document available, ASME and CSA are not undertaking to render professional or other services for or on behalf of any p

10、erson or entity or to perform any duty owed by any person or entity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and ASME and CSA accept no responsibility whatsoever arising in any way

11、from any and all use of or reliance on the information contained in this document. ASME and CSA have no power, nor do they undertake, to enforce compliance with the contents of the standards or other documents they jointly publish. Authorized use of this document This document is being provided by A

12、SME and CSA for informational and non-commercial use only. The user of this document is authorized to do only the following: If this document is in electronic form: load this document onto a computer for the sole purpose of reviewing it; search and browse this document; and print this document. Limi

13、ted copies of this document in print or paper form may be distributed only to persons who are authorized by ASME and CSA to have such copies, and only if this Legal Notice appears on each such copy. In addition, users may not and may not permit others to alter this document in any way or remove this

14、 Legal Notice from the attached standard; sell this document without authorization from ASME and CSA; or make an electronic copy of this document. If you do not agree with any of the terms and conditions contained in this Legal Notice, you may not load or use this document or make any copies of the

15、contents hereof, and if you do make such copies, you are required to destroy them immediately. Use of this document constitutes your acceptance of the terms and conditions of this Legal Notice. Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or netw

16、orking permitted without license from IHS-,-,-CSA Standards Update ServiceASMEA112.18.2-2011/ CSAB125.2-11June 2011Title: Plumbing waste fittingsPagination: 41 pages (xv preliminary and 26 text), each dated June 2011To register for e-mail notification about any updates to this publicationgo to www.S

17、hopCSA.caclick on E-mail Services under MY ACCOUNTclick on CSA Standards Update ServiceThe List ID that you will need to register for updates to this publication is 2420763.If you require assistance, please e-mail techsupportcsa.ca or call 416-747-2233.Visit CSAs policy on privacy at www.csagroup.or

18、g/legal to find out how we protect your personal information.Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTENTIONALLY LEFT BLANKCopyright ASME International Provided by IHS under license with

19、 ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASMEA112.18.2-2011/ CSAB125.2-11Plumbing waste fittingsASME/CSA StandardCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license

20、from IHS-,-,-Published in June 2011 by Canadian Standards AssociationA not-for-profit private sector organization5060 Spectrum Way, Suite 100Mississauga, Ontario, CanadaL4W 5N61-800-463-6727 416-747-4044Visit the CSA Online Store at www.ShopCSA.caISBN 978-1-55436-981-2 Canadian Standards Association

21、 2011All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher.Commitment for AmendmentsThis Standard is issued jointly by the American Society of Mechanical Engineers (ASME) and the Canadian Standards Association (CSA). A

22、mendments to this Standard will be made only after processing according to the Standards writing procedures of both ASME and CSA.The American Society of Mechanical Engineers (ASME) Three Park AvenueNew York, NY 10016-5990USAwww.asme.orgISBN 978-0-7918-3177-9 Copyright 2011The 2011 edition of this St

23、andard is being issued with an automatic addenda subscription service. The use of addenda allows revisions made in response to public review comments or committee actions to be published as necessary.Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction o

24、r networking permitted without license from IHS-,-,-June 2011 iiiContents The American Society of Mechanical Engineers Canadian Standards AssociationPlumbing waste fittingsASME Standards Committee on Plumbing Materials and Equipment viASME Project Team 18.2 Fixture Waste Fittings viiiCSA Technical C

25、ommittee on Plumbing Fittings xASME/CSA Joint Harmonization Task Group on Plumbing Fittings xiiPreface xiv1Scope 12 Reference publications 23 Definitions and abbreviations 33.1 Definitions 33.2 Abbreviations 44 General requirements 44.1 Materials 44.1.1 General 44.1.2 All waste fittings 54.1.3 Plast

26、ic tubular waste fittings 54.1.4 Plastic pipe and pipe fittings 54.1.5 Copper alloys 54.1.6 Cast iron 54.1.7 Ductile iron 54.1.8 Stainless steel 54.1.9 Elastomeric fittings 54.2 Installation 54.2.1 Connection to waste system 54.2.2 Protection of finish 64.2.3 Fixture seal 64.3 Threads 64.3.1 DWV pla

27、stic pipe and fittings 64.3.2 Metallic pipes and fittings 64.3.3 Compression and union nuts 64.3.4 Tapped bosses 64.4 Solder connections 64.5 Replacement parts 64.5.1 Use of standard tools 64.5.2 Replacement part design 64.6 Dimensions 64.6.1 Outlet size 64.6.2 Slip joints 74.6.3 Wall thickness 74.6

28、.4 Sink strainer assemblies 74.6.5 Traps 74.6.6 Tubing stops 84.6.7 Subdrains for built-up shower pans 8Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- The American Society of Mechanical Engineer

29、sASMEA112.18.2-2011/ CSAB125.2-11 Canadian Standards Associationiv June 20114.6.8 Grey water diverters 84.7 Mechanical stoppers 95 Performance requirements and test procedures 95.1 General 95.1.1 Preconditioning 95.1.2 Installation for testing 95.1.3 Testing sequence 95.2 Corrosion 105.2.1 Performan

30、ce requirements 105.2.2 Test procedure 105.3 Thermal cycling 105.3.1 Performance requirements 105.3.2 Test procedure 115.4 Coatings 115.5 Shower drain strainers 115.5.1 Performance requirements 115.5.2 Load test procedure 115.6 Sink strainer assemblies 115.6.1 Performance requirements 115.6.2 Hot oi

31、l exposure 115.6.3 Water absorption 125.6.4 Point impact 125.7 Body and clamping rings of subdrains for built-up shower pans 135.8 Minimum flow rate 135.8.1 Performance requirements 135.8.2 Test procedure 135.8.3 Grey water diverters 135.9 Strength 135.9.1 Thread torque strength 135.9.2 Hydrostatic

32、pressure 145.10 Life cycle 145.10.1 Performance requirements 145.10.2 Test procedure 145.11 Seals leakage 145.11.1 Waste fittings for drainage flow control 145.11.2 Other waste fittings 146 Markings, packaging, and installation instructions 156.1 General 156.2 Packaging 156.3 Instructions for elasto

33、meric waste fittings 156.4 Grey water diverters 156.4.1 Markings 156.4.2 Instructions 15AnnexesA (informative) Unit conversion and rounding criteria 26Figures1 Sink and lavatory waste, trap, centre outlet, and patent overflow fittings 162 Trap wall adapter 163 Sink strainer 174 Sink strainer tailpie

34、ce 17Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- The American Society of Mechanical Engineers Canadian Standards AssociationPlumbing waste fittingsJune 2011 v5 Tee 186 Twin waste elbow 187 Ce

35、ntre outlet Continuous waste assembly 198 End outlet Continuous waste assembly 199 Typical subdrain for built-up shower pans 2010 Grey water diverter Test of water flow through the sanitary drainage system outlet 2111 Grey water diverter Test of water flow through the diversion outlet 2212 Grey wate

36、r diverter Test of water with the diversion mechanism in the diverted position and the diversion outlet blocked 2313 Typical lavatory pop-up drain 2414 Waste and overflow 25Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted with

37、out license from IHS-,-,- The American Society of Mechanical EngineersASMEA112.18.2-2011/ CSAB125.2-11 Canadian Standards Associationvi June 2011ASME Standards Committee on Plumbing Materials and EquipmentD.W. Viola IAPMO,Mokena, Illinois, USAChairS.A. Remedios Delta Faucet Company,Indianapolis, Ind

38、iana, USAVice-ChairR.H. Ackroyd Rand Technical Consulting,Newburyport, Massachusetts, USAS.F. Aridi NSF International,Ann Arbor, Michigan, USAJ.A. Ballanco JB Engineering however, they should not contain proprietary names or information.ASME procedures provide for reconsideration of any interpretati

39、on when or if additional information that might affect an interpretation is available. Further, persons aggrieved by an interpretation may appeal to the cognizant ASME Committee.Interpretations are published on the ASME Web site under the Committee Pages at http:/www.asme.org/codes/ as they are issu

40、ed.CSA Notes:(1) Use of the singular does not exclude the plural (and vice versa) when the sense allows.Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- The American Society of Mechanical Engineer

41、s Canadian Standards Association Plumbing waste fittingsJune 2011 xv(2) Although the intended primary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose.(3)

42、 This publication was developed by consensus, which is defined by CSA Policy governing standardization Code of good practice for standardization as “substantial agreement. Consensus implies much more than a simple majority, but not necessarily unanimity”. It is consistent with this definition that a

43、 member may be included in the Technical Committee list and yet not be in full agreement with all clauses of this publication.(4) To submit a request for interpretation of CSA Standards, please send the following information to inquiriescsa.ca and include “Request for interpretation” in the subject

44、line:(a) define the problem, making reference to the specific clause, and, where appropriate, include an illustrative sketch;(b) provide an explanation of circumstances surrounding the actual field condition; and(c) where possible, phrase the request in such a way that a specific “yes” or “no” answe

45、r will address the issue.Committee interpretations are processed in accordance with the CSA Directives and guidelines governing standardization and are published in CSAs periodical Info Update, which is available on the CSA website at http:/standardsactivities.csa.ca.(5) CSA Standards are subject to

46、 periodic review, and suggestions for their improvement will be referred to the appropriate committee. To submit a proposal for change to CSA Standards, please send the following information to inquiriescsa.ca and include “Proposal for change” in the subject line:(a) Standard designation (number);(b

47、) relevant clause, table, and/or figure number;(c) wording of the proposed change; and(d) rationale for the change.(6) Attention is drawn to the possibility that some of the elements of this Standard may be the subject of patent rights. CSA is not to be held responsible for identifying any or all su

48、ch patent rights. Users of this Standard are expressly advised that determination of the validity of any such patent rights is entirely their own responsibility.Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTENTIONALLY LEFT BLANKCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,