ANSI ASME A112.1.3-2000 Air Gap Fittings for Use with Plumbing Fixtures Appliances and Appurtenances《卫生设备 器具和附件的空隙配套件》.pdf

《ANSI ASME A112.1.3-2000 Air Gap Fittings for Use with Plumbing Fixtures Appliances and Appurtenances《卫生设备 器具和附件的空隙配套件》.pdf》由会员分享，可在线阅读，更多相关《ANSI ASME A112.1.3-2000 Air Gap Fittings for Use with Plumbing Fixtures Appliances and Appurtenances《卫生设备 器具和附件的空隙配套件》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、ASME A112.1.3-2000AIR GAP FITTINGS FOR USE WITH PLUMBING FIXTURES,APPLIANCES, ANDAPPURTENANCESAN AMERICAN NATIONAL STANDARDREAFFIRMED 2015FOR CURRENT COMMITTEE PERSONNELPLEASE E-MAIL CSasme.orgAN AMERICAN NATIONAL STANDARDAIR GAP FITTINGS FOR USE WITH PLUMBING FIXTURES,APPLIANCES, ANDAPPURTENANCESAS

2、ME A112.1.3-2000Date of Issuance: September 11, 2000This Standard will be revised when the Society approves the issuance ofa new edition. There will be no addenda or written interpretations of therequirements of this Standard issued to this edition.ASME is the registered trademark of The American So

3、ciety of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards. The Standards Committee that approved the code or standardwas balanced to assure that individuals from competent and concerned interests have had anop

4、portunity to participate. The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input from industry, academia,regulatory agencies, and the public-at-large.ASME does not “approve,” “rate,” or “endorse” any item, construction,

5、proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection with any items mentioned in this document, and does not undertake to insure anyoneutilizing a standard against liability for infringement of any applicable letters p

6、atent, nor assumeany such liability. Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights, and the risk of infringement of such rights, is entirely theirown responsibility.Participation by federal agency representative(s) or person(s) affiliat

7、ed with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued inaccordance with the established ASME procedures and policies, which precludes the issuanceof interpretations by

8、 individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue, New York, NY 10016-5990Copyright 2000 byTHE AMERICAN SOCIETY OF MECH

9、ANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.FOREWORDIndustry has often incorporated air gaps into commercial fittings to provide back siphonageand backflow protection for the water supply systems to which the fittings are connected.Designers of such fittings took guidance from documents such

10、 as ASME A112.1.2, butthere was not a national standard specifically directed toward fittings that included air gaps.In response to requests to modify ASME A112.1.2 to specifically cover fittings with airgaps, the ASME A112 Main Committee determined that the better course was to developa separate st

11、andard for this purpose. A Project Team was created, and this Standard is theresult of that work.Suggestions for improvement of this Standard are welcomed. They should be sent to TheAmerican Society of Mechanical Engineers; Attn: Secretary, A112 Main Committee; ThreePark Avenue, New York, NY 10016.T

12、his Standard was approved as an American National Standard on July 5, 2000.iiiASME STANDARDS COMMITTEE A112Standardization of Plumbing Materials and Equipment(The following is the roster of the Committee at the time of approval of this Standard.)OFFICERSP. J. Higgins, ChairS. A. Remedios, Vice Chair

13、C. J. Gomez, SecretaryCOMMITTEE PERSONNELR. H. Ackroyd, Rand EngineeringJ. A. Ballanco, JB Engineering 0.5 gpm (1.892 L/min) for maximumAIR GAP FITTINGS FOR USE WITH PLUMBING FIXTURES,APPLIANCES, AND APPURTENANCES ASME A112.1.3-2000rated flow between 1 and 10 gpm (3.785 and 37.85L/min); 2 gpm (7.570

14、 L/min for flow rated from greaterthan 10 gpm (37.85 L/min) up to 20 gpm (75.70 L/min); and 5 gpm (18.92 L/min) for flow rated greaterthan 20 gpm (75.70 L/min).5.3.2 Any entrance of water into the sight tube shallbe cause for rejection of the device.5.4 Back Pressure Test5.4.1 This test shall be con

15、ducted on air gap fittingswhich are rated by their manufacturer to protect againstbackflow into the outlet of the fitting. With the fittinginstalled in accordance with the manufacturers installa-tion instructions, the manufacturers maximum ratedback pressure or backflow shall be applied. The flowsha

16、ll be maintained at least 20 sec after the height ofback flowing water stabilizes. Verify that during thistest that the water does not rise above the manufacturerscritical level mark on the fitting.35.4.2 Water above the critical level mark shall because for rejection of the fitting.6 MARKINGSAir ga

17、p fittings shall be permanently marked withthe following information:(a) the manufacturers name or trademark.(b) the manufacturers model number.(c) the manufacturers critical level mark.(d) “inlet” or “outlet” or flow direction. If the fittinghas multiple inlets, all inlets shall be marked.7 INSTALL

18、ATION INSTRUCTIONSInstallation instructions that describe the proper instal-lation of the fitting with respect to the critical leveland to the orientation required for the fitting to complywith the performance tests of Section 5 shall be providedwith the fitting. Manufacturers literature shall inclu

19、dethe maximum rated flow to the inlet(s) and any backpressure or back flow rating.ASME STANDARDS RELATED TO PLUMBINGAir Gaps in Plumbing Systems A112.1.2-1991(R1998)Air Gap Fittings for Use With Plumbing Fixtures, Appliances, and AppurtenancesA112.1.3-2000Performance Standard and Installation Proced

20、ures forStainless Steel Drainage Systems for Sanitary, Storm, andChemical Applications, Above and Below Ground .A112.3.1-1993Water Heater Relief Valve Drain Tubes A112.4.1-1993(R1998)Plastic Fittings for Connecting Water Closets to theSanitary Drainage System A112.4.3-1999Floor-Affixed Supports for

21、Off-the-Floor Plumbing Fixtures forPublic UseA112.6.1M-1997Backwater Valves A112.14.1-1975(R1998)Plumbing Fixture Fittings . A112.18.1-2000Performance Requirements for Backflow Protection Devicesand Systems in Plumbing Fixture Fittings A112.18.3M-1996Flexible Water Connectors A112.18.6-1999Deck-Moun

22、ted Bath/Shower Transfer ValvesWith Integral Backflow Protection . A112.18.7-1999Enameled Cast Iron Plumbing Fixtures .A112.19.1M-1994(R1999)Vitreous China Plumbing Fixtures A112.19.2M-1998Stainless Steel Plumbing Fixtures (Designed forResidential Use) .A112.19.3M-1987(R1996)Porcelain Enameled Forme

23、d Steel Plumbing Fixtures.A112.19.4M-1994(R1999)Trim for Water-Closet Bowls, Tanks, and Urinals A112.19.5-1999Hydraulic Performance Requirements for Water Closets and Urinals . A112.19.6-1995Whirlpool Bathtub Appliances .A112.19.7M-1995Suction Fittings for Use in Swimming Pools, Wading Pools,Spas, H

24、ot Tubs, and Whirlpool Bathtub Appliances A112.19.8M-1987(R1996)Non-Vitreous Ceramic Plumbing Fixtures.A112.19.9M-1991(R1998)Dual Flush Devices for Water Closets A112.19.10-1994Wall Mounted and Pedestal Mounted, Adjustable and PivotingLavatory and Sink Carrier Systems. A112.19.12-2000Floor Drains .A

25、112.21.1M-1991(R1998)Roof DrainsA112.21.2M-1983Hydrants for Utility and Maintenance Use A112.21.3M-1985(R1995)Cleanouts .A112.36.2M-1991(R1998)The ASME Publications Catalog shows a complete list of all the Standards published bythe Society. For a complimentary catalog, or the latest information abou

26、t our publications,call 1-800-THE-ASME (1-800-843-2763).Member Services & Benefits Public InformationOther ASME Programs Self-Study CoursesCredit Card Orders Payment Inquiries Shipping InformationIMechE Publications Professional Development Subscriptions/Journals/MagazinesMeetings & Conferences Symp

27、osia VolumesMember Dues Status Technical PapersThere are four options for making inquiries* or placing orders. Simply mail, phone, fax, or E-mail us and an InformationCentral representative will handle your request.Mail Call Toll Free Fax-24 hoursUS & Canada: 800-THE-ASME 973-882-171722 Law Drive, B

28、ox 2900 (800-843-2763) 973-882-5155Fairfield, New Jersey Mexico: 95-800-THE-ASME07007-2900 (95-800-843-2763)Universal: 973-882-1167* Information Central staff are not permitted to answer inquiries about the technical content of this code or standard.Information as to whether or not technical inquiri

29、es are issued to this code or standard is shown on the copyrightpage. All technical inquiries must be submitted in writing to the staff secretary. Additional procedures for inquiriesmay be listed within.E-Mail- 24 hours Infocentralasme.orgPublicationsShort CoursesASME ServicesASMEASME is committed to developing and delivering technical information. At ASMEs Information Central, we makeevery effort to answer your questions and expedite your orders. Our representatives are ready to assist you in thefollowing areas:ASME PressCodes & StandardsHow can you reach us? Its easier than ever!J15500